Installation Guide

ManualsBrandsTITAN ManualsSecurity Doors1S2001EN1RHP3A

Premium Security Screen Door

Installation Instructions

Recessed Mount

• Read completely through the installation instructions before proceeding with installation

• Installation requires two people

• Use appropriate protective equipment, including safety glasses

• Children should not be allowed in work area

• Failure to install door correctly could result in injury

Above average degree of difculty. Requires

installation experience.

PROFESSIONAL INSTALLATION RECOMMENDED

Even professional installers will benet from watching.

REVIEW INSTALLATION VIDEO

Customer service and technical support are available.

Monday - Friday: 7:00am - 5:00pm PT

1-866-317-8867

support@uhdco.com

NEED HELP?

RETAIN PACKAGING DURING INSTALLATION

Do NOT discard packaging materials until

installation is complete

RECOMMENDED TOOLS

Safety Glasses Measuring Tape

Level

1/8" Drill Bit

minimum length: 4"

Phillips-head

screwdriver

HacksawBox Cutter

Wood Blocks (2"x4"x6")

Shims

Paintable Caulk &

Caulk Gun

Tin Snips

Drill

INSTALLATION

EASY HARD

INSTALLATION

EASY HARD

INSTALLATION

EASY HARD

INSTALLATION

EASY HARD

INSTALLATION

EASY HARD

INSTALLATION

EASY HARD

Pencil

MK1229 04062020

1/2" Spade Drill Bit

Summary of content (14 pages)

PAGE 1
Recessed Mount Premium Security Screen Door Installation Instructions • • • • • Read completely through the installation instructions before proceeding with installation Installation requires two people Use appropriate protective equipment, including safety glasses Children should not be allowed in work area Failure to install door correctly could result in injury RETAIN PACKAGING DURING INSTALLATION Do NOT discard packaging materials until installation is complete PROFESSIONAL INSTALLATION RECOMMENDED
PAGE 2
DOOR PARTS A) Hinge-side jamb B) Door slab C) Lock-side jamb D) Top header jamb E) Mulit-blade bug sweep HARDWARE & FASTENERS F) Weatherstripping G) Touch-up paint H) #8 x 1-1/4" self-tapping mounting screws (12) I) #8 x 5/8" self-tapping screws (2) F D G B A 3-1/2” flathead E 3-1/2”flathead flathead 2-1/2” C H 2-1/2” flathead1” flathead 2” drywall 1” flathead 2” drywall 1/2” flathead 1/2” panhead I self drilling 1/2” flathead 1/2” self 5/8” panh
PAGE 3
1 Determining Remove glass Your panel Build (optional) Out Area (continued) If your door includes glass, remove it before you start the installation procedure. Loosen (do not remove) each screw. Carefully hold the glass panel in place and rotate each clip 90°. Carefully remove the glass panel and store it in a safe place during installation. Rotate 90° clips 2 Determining Install top jamb Your and Build measure Out Area length (continued) of side jambs 1.
PAGE 4
3 Determining Trim the jambYour Build Out Area (continued) Use the measurement taken in step 2, mark each jamb (A,C) down from the top (see diagram, hinge pins face the top of the jamb). Using a hacksaw and a metal cutting blade, trim the bottom of each jamb at the mark you made. Top of hinge-side jamb (A) (Warning: do NOT cut at top) Top of latch-side jamb (C) (Warning: do NOT cut at top) Note: verify that direction of hinge pins match illustration before cutting bottom of jamb.
PAGE 5
Determining Install the door Your Build Out Area (continued) Hang the security door (B) on the hinges, holding the door open to a 90o angle and starting with the bottom pin first. Applied to door panel Reminder: Maintain annually. Apply white grease to hinge pins. (Hinge pins come pre-lubricated from factory).
PAGE 6
8 Determining Install the latch-side Your Build jamb Out Area (continued) Re-insert lock-side jamb (C). Check reveal by closing door. Gap should be about 5/32". Use shims or spacers to set reveal. Drill 1/8" holes 3/4" deep through the mounting hole marks at E, F, G & H holes. Attach the latch-side jamb using 4 of the #8 x 1-1/4" mounting screws (H) provided, being sure to maintain the 5/32" reveal throughout the mounting process. Push jamb up into corner tight against the top jamb.
PAGE 7
10 Re-install Determining glass Your panel Build and Out install Areaweatherstripping (continued) Re-install glass panel if removed prior to door installation. Install foam weatherstripping (F) around top and both sides of door. Final Determining touch-up suggestions Your Build Out Area (continued) Caulk (not included) Caulk around the outside of the security door jamb frame, using paintable caulk, and paint to the desired color.
PAGE 8
Montaje empotrado Instalación de puertas premium de seguridad • • • • • Lee todas las instrucciones de instalación del kit antes de la instalación La instalación requiere de dos personas Usa el equipo de protección apropiado, incluyendo gafas de seguridad Mantén los niños alejados del área de trabajo Instalar incorrectamente la puerta puede causar lesiones CONSERVA EL EMPAQUE DURANTE LA INSTALACIÓN NO deseches los materiales del empaque hasta que la instalación haya terminado.
PAGE 9
PIEZAS DE LA PUERTA A) Jamba del lado de las bisagras B) Hoja de la Puerta C) Jamba del Lado de la cerradura D) Jamba del travesaño superior E) Guardapolvo contra insectos, de aletas múltiples HERRAJES Y SUJETADORES F) Weatherstripping G) Pintura para retoques H) Montar tornillo que auto utilizando, núm. 8 x 1-1/4" (12) I) Tornillos autorroscantes de montaje, núm.
PAGE 10
1 Remove Determining Retire el panel glass Your panel de Build vidrio (optional) Out (opcional) Area (continued) Si tu puerta tiene un panel de vidrio, quítalo antes de empezar a instalar. Afloja (sin quitar) cada tornillo. Con cuidado sostén el panel de vidrio en su sitio y rota cada presilla 90°. Quita el panel de vidrio delicadamente y guárdalo en un lugar seguro durante la instalación.
PAGE 11
3 Determining Cómo cortar Your la jamba Build Out Area (continued) Usa las medidas que tomaste en el paso 2; marca cada jamba (A,C) desde arriba hacia abajo (ver diagrama: los pasadores de la bisagra deben quedar hacia la parte superior de la jamba). Con una sierra para metales y una cuchilla para metales, corta la parte inferior de cada jamba donde marcaste.
PAGE 12
5 Determining Colgar la puerta Yourde Build seguridad Out Area (continued) Cuelga la puerta de seguridad (B) en las bisagras sosteniendo la puerta abierta en un ángulo de 90 grados. Comienza por los pasadores de abajo. Aplicar al panel de la puerta Recuerda: Dale mantenimiento una vez al año. Aplica grasa blanca a los pasadores de las bisagras. (Los pasadores de las bisagras vienen prelubricados de fábrica).
PAGE 13
8 Determining Instala la jamba Yourdel Build ladoOut delArea pestillo (continued) Vuelve a insertar la jamba del lado del pestillo (C). Cierra la puerta para verificar que hay un espacio de reborde. El espacio debe ser de aproximadamente 5/32". Usa cuñas o espaciadores para marcar el espacio. Taladra orificios de 1/8" y 3/4" de profundidad a través las marcas para los tornillos de montaje E, F, G, y H. Instala la jamba del lado del pestillo con 4 de los tornillos montaje, de acero inoxidable Núm.
PAGE 14
10 Vuelva Determining a instalar YourelBuild panelOut de Area vidrio(continued) e instale el burlete Vuelva a instalar el panel de vidrio si se quitó antes de la instalación de la puerta Instale burletes de espuma (F) alrededor de la parte superior y ambos lados de la puerta. Sugerencias Determining finales Yourde Build retoque Out Area (continued) Pasta selladora (no incluido) Aplica pasta selladora pintable por el exterior del marco de la jamba de tu puerta de seguridad y pinta del color deseado.