Programs and Operation Controller 1. Power 2. Timer 3. Pause 4-8. Auto Programs 1 3 2 9. Manual Air 10-11. Width 12-13. Position 14. 9iEration 15. Heat 16. Spot/Partial 17. Intensity 18. Speed 19. =ero *raYity 20. )oot Air 21. )ootrest /iIt 22. )ootrest 'rop 23. Recline 24. Incline 25. Kneading 26. Tapping 27. Shiatsu 28.
Programs and Operation "VUPNBUJD NBTTBHF QSPHSBNT The OS-4000CS features 5 automatic massage program to help you enjoy the benefits of a relaxing and inYigorating massage. Press the [ ] button to switch on. The chair will recline into ready position. Ready position /eg rest will raise slightly and bacNrest will recline slightly. Select any of the 5 automatic massage programs '((P TISS8(, STR(TCH, (1(R*<, R(/A; and )8// AIR refer to page 14-15 for details and press the button.
Programs and Operation .BOVBM NBTTBHF QSPHSBNT Press the [ ] button to switch on. The chair will recline into ready position. Ready position /eg rest will raise slightly and bacNrest will recline slightly. Press the [ position or [ position. VIBRATION HEAT ] button to recline to zero graYity ] [ ] button to your desired Select any of the 4 manual massage programs K1(ADI1*, TAPPI1*, SHIATS8 or RO//I1* refer to page 17 for details and press the button.
Programs and Operation Manual massage mode Action Speed Intensity Width S/P Timer Button Kneading Tapping Shiatsu Rolling Manual Air MANUAL AIR Combination of manual massage Action %utton Heat 9ibration )oot Air Manual Air Kneading Tapping Shiatsu Rolling Stopping a massage session Press the [ ] button to stop the massage functions. The rollers will moYe bacN to the storage position and all airbags will deflate, ending the massage.
Programs and Operation Programs Description 1.Power Starts and stops all functions of the massage chair. Press once. Remote control will light up and chair will be in idle mode.
Programs and Operation 7.Relax (ngages the full body relax auto program. This program will start with slow kneading and heaYy tapping massage, progressing to in-depth massage targeting the neck and lower back. 8.Full Air (ngages the the full body air pressure auto program. This program applies full body air pressure massage to shoulder, arm, palm, lower back, buttocks, thighs, calYes and feet.
Programs and Operation 15. Heat Heat function is set to O)) by default. Press this button once to actiYate the waist heating function. Press the button again to stop the waist heating function. It is applicable during any Automatic Program, /ocalised Area Program or Manual Program. 16. Spot/Partial (S/P) Press once to localize the massage to a particular point. Press again to shift massage to a particular area of body. This will keep the original massage node working on a range of 8cm.
Programs and Operation 23/24. Recline / Incline Control the recline / incline angle of the chair. Press once and the backrest will moYe to a horizontal reclining position or an upright sitting position. Press again to stop at your preferred angle. 25. Kneading Press this button once to actiYate the kneading function for a full back massage. Press again to stop the kneading function. Kneading function strength can be adjusted by pressing ³Speed´ button after actiYating kneading function.
Troubleshooting This page summarizes the most common problems you could encounter with the product. If you are unable to solYe the problem with the information below, contact serYice center immediately. If the problem encountered is not listed, please try the following suggestions: 1. Turn off the product and unplug it. 2. Wait for 60 minutes. 3. Plug the product back to the recommended outlet and restart. 4. If the problem persists, contact the authorized serYice center.
Care and Storage 1. Cleaning 1eYer use scouring pads, abrasiYe cleaning agents or aggressiYe liTuids such as petrol or acetone to clean the appliance. When wiping down the chair use non toxic cleaners and be sure the cloth is moist and 1OT wet. Do not immerse to appliance in water. 1 2 3 RemoYe the main plug from the wall socket. Clean the control panel and cords with a dry cloth. Do not use a moist cloth or a cleaning agent. 2. Storing 1 Disconnect the product from the power source after use.
