OS 4000CS Instruction Manual
Thank you for purchasing the OS 4000CS Massage Chair. Before using your massage chair, please read the contents of this instruction manual and refer to it when needed. Contents Safety Precautions ………………………..……............................. 1-2 Chair Components ………………………..……............................. 3-4 Chair Installation ……………………………………...................... 5-7 Preparation before Use……………………………………..……..... 8-9 Controller Diagram……………………………………...….............. 10 Programs and Operation………………………………...
Safety Precautions When using the massage chair, basic precautions should always be followed to reduce the risk of electric shock, burns, fire or injury to persons. Please read the following precautions before using the massage chair. ● Make sure the power plug is securely inserted into a proper electrical outlet to reduce the risk of short-circuit and fire. ● It is highly recommended that a surge protector is used to prevent from damage.
Safety Precautions ● Please consult your doctor if you are in doubt as to whether or not you should use this massage chair. ● Please consult a doctor before using the massage chair if you are pregnant, undergoing any medical treatment, using a medical electronic device such as a pacemaker, or are experiencing any of the following: Malignant tumor, heart disease, back pain, abnormal or curved back bone, osteoporosis or acute illness.
Chair Components 8 1 9 2 3 10 4 5 11 6 12 7 1 Pillow Pad 2 Backrest Pad 3 Controller 4 USB 5 Seat Pad 6 Calvesrest 7 Footrest 8 Backrest 9 Shoulder 10 Armrest 11 Side Panel 3 12 Legrest
Chair Components Massage Position 2 Air bags 8 Air bags 2 Heat 1 Vibration 8 Air bags 8 Air bags Air bag Heat 4 Vibration
Chair Installation 1. Take out the main unit and accessories from two boxes. Main unit Accessories Bolt A x2 Bolt B x1 Base Legrest Split Pin x3 2. Connect the wires and air pipes from the footrest and seat part respectively.
Chair Installation 3. Align the connecting holes from the footrest and seat part. Insert bolt A and secure with split pin as demonstrated.
Chair Installation 4. Lift the legrest to a horizontal position and align the connecting hole. Insert bolt B and secure with split pin as demonstrated. 5. Attach the seat cover and footrest cover with the zipper.
Preparation before Use 1. Placing the chair Ensure sufficient spaces around massage chair, please leave 4.7” of spaces behind the backrest and 7.1” of spaces at the front of massage chair. at least 4.7” at least 7.1” 2.Moving the chair Lift up the footrest then recline the chair to approximate 45°to easily move the chair around the house with a slight pull or push ! Caution 1. Before moving the chair, please adjust the legrest back into the original position. 2.
Preparation before Use 3. Placing the cushion pad Note: The back pad is installed with an additional pad to soften the massage.If you desire a stronger massage simply remove the extra pad and proceed to zippering the pad to the top of the backrest. 4. Switching the power on 1 2 3 Connect the wire plug . Connect to the power supply. Turn the switch to “I” position.
Programs and Operation Controller 1. Power 2. Timer 3. Pause 4-8. Auto Programs 9. Manual Air 10-11. Width 12-13. Position 14. Vibration 15. Heat 16. Spot/Partial 17. Intensity 18. Speed 19. Zero Gravity 20. Foot Air 21. Footrest Lift 22. Footrest Drop 23. Recline 24. Incline 25. Kneading 26. Tapping 27. Shiatsu 28.
Programs and Operation Automatic massage programs The OS-4000CS features 5 automatic massage program to help you enjoy the benefits of a relaxing and invigorating massage. Press the [ ] button to switch on. The chair will 1 recline into ready position. (Ready position: Leg rest will raise slightly and backrest will recline slightly.) Select any of the 5 automatic massage programs DEEP TISSUE, STRETCH, ENERGY, RELAX and 2 FULL AIR (refer to page 14-15 for details) and press the button.
Programs and Operation Manual massage programs Press the [ ] button to switch on. The chair will 1 recline into ready position. (Ready position: Leg rest will raise slightly and backrest will recline slightly.) Press the [ 2 position or [ position. ] button to recline to zero gravity ] [ ] button to your desired Select any of the 4 manual massage programs VIBRATION HEAT 3 KNEADING, TAPPING, SHIATSU or ROLLING (refer to page 17 for details)and press the button.
Programs and Operation Manual massage mode Action Speed Intensity Width S/P Timer Button Kneading Tapping Shiatsu Rolling Manual Air MANUAL AIR Combination of manual massage Action Button Heat Vibration Foot Air Manual Air Kneading Tapping Shiatsu Rolling Stopping a massage session Press the [ ] button to stop the massage functions. The rollers will move back to the storage position and all airbags will deflate, ending the massage.
Programs and Operation Programs Description 1.Power • Starts and stops all functions of the massage chair. • Press once. Remote control will light up and chair will be in idle mode. • You can press any massage function buttons to begin your massage session, at a default time of 15 minutes. • Press again, all functions will stop and massage rollers will return to original position. 2.Timer • Controls the duration of the massage session. • The default time for all massage functions is 15 minutes.
Programs and Operation 7.Relax • Engages the full body relax auto program. • This program will start with slow kneading and heavy tapping massage, progressing to in-depth massage targeting the neck and lower back. 8.Full Air • Engages the the full body air pressure auto program. • This program applies full body air pressure massage to shoulder, arm, palm, lower back, buttocks, thighs, calves and feet.
Programs and Operation 15. Heat • Heat function is set to OFF by default. • Press this button once to activate the waist heating function. Press the button again to stop the waist heating function. • It is applicable during any Automatic Program, Localised Area Program or Manual Program. 16. Spot/Partial (S/P) • Press once to localize the massage to a particular point. • Press again to shift massage to a particular area of body. • This will keep the original massage node working on a range of 8cm.
Programs and Operation 23/24. Recline / Incline • Control the recline / incline angle of the chair. • Press once and the backrest will move to a horizontal reclining position or an upright sitting position. Press again to stop at your preferred angle. 25. Kneading • Press this button once to activate the kneading function for a full back massage. Press again to stop the kneading function. • Kneading function strength can be adjusted by pressing “Speed” button after activating kneading function.
Troubleshooting This page summarizes the most common problems you could encounter with the product. If you are unable to solve the problem with the information below, contact service center immediately. If the problem encountered is not listed, please try the following suggestions: 1. Turn off the product and unplug it. 2. Wait for 60 minutes. 3. Plug the product back to the recommended outlet and restart. 4. If the problem persists, contact the authorized service center.
Care and Storage 1. Cleaning Never use scouring pads, abrasive cleaning agents or aggressive liquids such as petrol or acetone to clean the appliance. When wiping down the chair use non toxic cleaners and be sure the cloth is moist and NOT wet. Do not immerse to appliance in water. 1 2 3 Remove the main plug from the wall socket. Clean the control panel and cords with a dry cloth. Do not use a moist cloth or a cleaning agent. 2. Storing 1 Disconnect the product from the power source after use.
Grounding Instructions This product must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for the electric current to reduce the risk of electric shock. This product is equipped with a cord with an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
Chair Specifications Description Specifications Model No. OS 4000CS Rated Voltage 110V~120V Rated Frequency 50/60Hz Rated Power Consumption 200W Timer 5/10/15/20/25/30 minutes Max Time Rate 30 minutes Upright:63.4”x30.7”x47.2” Dimensions(L x W x H) Reclined:78.0”x30.7”x33.9” Carton 1 : 62.0"x32.5"x33.9" Carton 2 : 22.8"x19.7"x20.9" Weight Length of Wire Usage Condition Storage Condition Safety Feature Gross Weight: 271.7 lbs Net Weight: 226.6 lbs Controller wire: 59.