TI-Jupiter User's Manual t=::;:::::==================== Please read SAFETY INSTRUCTIONS carefully before using the chair.
Titan Chair Y Introduction to the Titan Jupiter y 1. The intelligent 3D technology will deliver a consistent soothing massage from your neck to down to your hamstrings. Adopting traditional Oriental massage methods, you will come to experience a soothing kneading, pressing, tapping and shiatsu style massage 1.Thank you for selecting the highly advanced Jupiter massage chair by TItan.. 2.Please read this manual carefully before using the massage chair. 3.
·----�- Safety instructions Please read this manual carefully to make sure the installation and operation of the massage chair is correct. SafetyI nstructions are provided in in this manual with Warning and Caution to ensure the safety of the user. • • Warning and Caution are highly important so please be aware of all safety warnings. A � • Warning This sign indicates warning of possible sever injury if not handled correctly. Caution This sign indicates caution.
Safety instructions • • A Caution The chair must be placed on a flat even surface. The backrest of the chair when upright must be placed a minimum of 10 cm from the wall. • T he maximum suggested operating time is 20mins. A maximum of 5 minutes for the upper, mid and lower back is advised to avoid injury. • -o· iil ::I (S) � To make sure the back lying. Too long time massage is bad for your body.
Installation Installation Step 2. Massage chair position return Step 1. How to move the chair CDCut the straps and unpack the box to access the base of the chair. Remove all pads and cushions from the base and lift the chair from the points indicated in image below. With 2 or more people, lift carefully and move the chair to the desired location. @Be sure to keep all the cushions, remote and power cord together so that nothing is lost. 1.
Installation Installation Step 4. How to assemble the left and right armrest A + (DUnscrew the bolt designated as M6 on the seat frame with cross screwdriver. ®Insert the hole on the on the armrest into the fixed bolt. ® Insert the square tube into the side piece of the seat frame. @ Be sure the side panel holes line up in the front and back. Thread the M6 bolt and proceed to tighten.
Manual control 0 1, Press the on button on the remote. Form there you can select a pre-set program or manual setting. In the manual setting you can select the duration of the massage. Prior to selecting a massage program you can sync your mobile or tablet device. �II 2, This button allows youto pause the massage and turn back on at your convenience.
Manual control After power is on, press on/off key, the buzzer gives a short ring, the LCD screen will turn on, showing the display as shown on the left. The screen will show the massage method, time and current working status, etc., all of the information will in be real-time. Main interface Width: 111 heat: 111 J lnten�ty: 111II I] bluetooth s:: *? - D) G!- Tapping Knocking D) en en CD Zero 2' 5· Set function by pressing Menu key. �- 3D .
imstrtrnction and function illustration Function Illustration ON/OFF • Legrest up and backrest down On/Off@t Press this buttorlll controller, backrest will go down and legrest go up. Release this button, backrest and legrest will stop moving and the angle will be maitained. • .... • Legrest extend and retract Legrest can extend or retract within a range of 15CM. • Backrest up and Legrest down Step1. Power on CD Put one end plug of power line in location "a" as shown.
Synthetic leather 8 Make sure there is no people or pet or anything within the range of backrest and legrest. 0 Switch off the power. • Plastic parts General cleaning Clean with a clean soft and dry cloth. O Dip cloth into neutral detergent, squeeze it and clean. @ Wipe with water-dipped but squeezed cloth. (Chemical or medical cleaning products are forbidden) 8 Be sure to return the backrest and legrest to the default position by using controller.
Technical data Trouble The massage chair does not work after being powered on. Possible reason Check if the control is on or not. Open control switch A massage function was not selected Choose massage function check if the power cord is firmly inserted into the outlet and the chair. Make sure plug and socket are connected. Wire or plug has been damaged. The fuse burned out. Something wrong with inner circuit There is beep sound from the Sound is originating from air pump or inside while working.