Titoe CNC 3018 Router User Manual
Contents We l c o m e - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1 Part 1: Parts list---------------------------------------------------------------3 Part 2: Machine Installation-------------------------------------------------8 Part 3: Grblcontrol-----------------------------------------------------------24 Part 4: Getting Started ------------------------------------------------------31 Part 5: Lasergrbl --
Welcome ☛ T h a n k s f o r p u r c h a s i n g Ti t o e C N C 3 0 1 8 p r o M a c h i n e Ti t o e i s a p r o d u c t i o n p l a n t o f 3 0 1 8 p r o s e r i e s p r o d u c t s a n d h a s b e e n s e r v i n g t h e m a n u f a c t u r e r c o m m u n i t y f o r m a n y y e a r s . We l o v e m a n u f a c t u r i n g , l o v e t o create, and provide our customers with excellent, high-performance, highq u a l i t y p r o d u c t s .
☛Software download: https://shimom.s3.us-east2 . a m a z o n a w s . c o m / Ti t o e / Ti t o e + C N C 3 0 1 8 p r o + E n g r a v e r + M a c h i n e . z i p ☛ S e a r c h " T i t o e " o n Yo u t u b e , y o u c a n w a t c h t h e v i d e o s a b o u t h o w t o assembly and how to use the GRBL software. Thank you so much for your recent order of our CNC 3018 pro machine. We h o p e y o u w i l l b e p l e a s e d w i t h b o t h t h e p r o d u c t a n d s e r v i c e y o u received.
Part 1: Parts list Serial number Name Type Qty Picture 1 Aluminum 20*40*290mm 2 2 Aluminum 20*20*360mm 2 3 working desk 15*180*300mm 1 4 X Linear guide Φ10*360mm 2 5 Y Linear guide Φ10*290mm 2 6 X screw T8(365mm) 2 3
4 7 Y screw T8(295mm) 2 8 Bakelite 9 Stepper motor 42*34mm 2 10 Spindle 775ER\100w\8000r mp 1 11 X Z-Parts 12 Y-Axis slider 10mm 4 13 Y-Axis nut seat T8-4 1 14 Milling Cutter Φ3.175mm\20°\0.
15 Spindle wires 60mm 1 16 Stepper wires 60mm 3 17 Offline controller(Optional) 18 Power Supply 19 Control Board 20 USB Cable 21 Plate Clamp 22 Winding Tube 1 24V\5A 1 1 1.
6 23 U Disk 4g 1 24 Allen Wrench 2mm 1 25 Allen Wrench 2.
31 Copper Nut 2 32 T Nut M5*20 16 33 Slider Nut M5*30 10 34 Spring 0.
Part 2:Machine Installation Bakelite： 8
STEP 1 Base Installation Note:Please prepare the required materials according to the serial n u m b e r.
STEP 1 10 Base Installation 1) Assemble PlateA.B and 2 aluminum profiles into a rectangle. 2) Pass the Yaxis through 2 sliders. 3) Fix two Yaxis inside the rectangle .
Step2 Table Installation 11
12
1) Fix the coupling on the motor with a small wrench. 2) Fix the motor on the Plat b board (the socket is upward) 3) Brass nuts and springs are inlaid in Nut Seat. Use the screw to pass through Plate A and Nut Seat. 4) Rotate the screw rod to the coupling, and fix the coupling with a small wrench. 5) Install bolts and nuts on 4 slides and a nut seat. (It doesn’t need to be too tight) 6) Slowly insert the nut into the groove of the aluminum plate.
Completed 14
Step3 Base & Bakelite-C Installation 1) Fix six bolts and nuts on the plate C. 2) Arrange the six nuts neatly h o r i z o n t a l l y. 3) Insert six nuts into the grooves of the aluminum plate and tighten the bolts.
Completed 16 Note: (1)The distance between Bakelite-C and 2040 aluminum profile is 46.5mm, and Bakelite-C should be kept at 90° from the bottom ( 2 ) Ti p s : F i r s t p u t t h e T- n u t i n t h e g a p o f 4 0 4 0 a l u m i n u m p r o f i l e , corresponding to the hole, and then tighten the bolts.
Step4 X-Z Axis Assembly Installation Note:Please prepare the required materials according to the serial number 17
18
1) Fix the coupling on the motor with a small wrench. 2) Fix the motor on the Plat C board (the socket is facing upwards) 3) Install two X-axis and two aluminum profiles on PlateC board 4 ) I n s e r t t h e b r a s s n u t a n d s p r i n g i n t o t h e X - Z a s s e m b l y, a n d u s e t h e screw rod to pass through the assembly to the coupling. 5) Fix the coupling and screw rod with a small wrench.
Step5 Bakelite-D Installation 1) Fix six bolts and nuts on the plate D. 2) Arrange the six nuts neatly h o r i z o n t a l l y. 3) Insert six nuts into the grooves of the aluminum plate and tighten the bolt.
Step6 Spindle Installation Note: If the spindle cannot be put in, you can gently pry it open w i t h a small wrench. Don't worry about being 21 damaged.
Step7 Control Board Installation Step7 22 1) Fix four bolts and nuts on the control board. 2) Arrange the four nuts neatly h o r i z o n t a l l y. 3) Insert four nuts into the grooves of the aluminum plate and tighten the bolts.
Step8 Wiring Diagram Step7 Note: The red dot on the spindle represents the positive pole, which is connected to the red wire. If there is no red dot , Please observe the rotation of the spindle. Clockwise means the connection i s c o r r e c t , a n d counterclockwise means that is wrong.
Part 3: Grblcontrol 1.Install the driver(software->Drive->CH340SER.exe) The Candle software can be recognized by the computer after the d r i v e r i n s t a l l e d s u c c e s s f u l l y. I f n o t , y o u c a n e x i t a n d r e i n s t a l l o r c o n t a c t c u s t o m e r s e r v i c e t o d o w n l o a d a n e w d r i v e r.
2.Open GrblControl software(software -> Grblcontrol -> grblControl.
Note:Choosing the right port is very important, it is related to whether your Candle software can be installed successfully To D e t e r m i n e y o u r M a c h i n e ' s C O M p o r t : • Wi n d o w s X P : R i g h t c l i c k o n " M y Computer", select "Manage", select "Device Manager". • Wi n d o w s 7 : C l i c k " S t a r t " R i g h t c l i c k "Computer" Select "Manage" Select "Device Manager" from left pane.
3.Check if the software is installed successfully • Console window print ” [CTRL+X] < Grbl 1.1f ['$' for help]” If the connection is successful. • Console window print ” Serial port error 1: No such file or directory “ indicate that the connection is failed.
What should I do if the connection fails? Reason: (1) The USB is not connected successfully. (2) The port is not selected correctly. (3) The port of the computer is broken. (4) The firmware of the control board is broken. Solution: (1) Check the wiring again to make sure that the USB connection is correct. (2) According to the previous method, check whether the port is correct. (3) Change a port or change a computer to operate.
Grblcontrol Use 29
Toll setting 30
Part 4:Getting Started After the machine is assembled, you can perform basic machine tests. The following is the recommended start up sequence for the system: 1. Make sure all the wires are connected.（ The control board is connected to the spindle, motor and computer respectively） 2 .Press the white button on the control panel, the Led light flashes and the fan rotates. 3 . S u c c e s s f u l l y i n s t a l l e d t h e d r i v e r a n d s t a r t t h e C a n d l e p r o g r a m .
5 . S e t t h e “ F e e d : ” t o a v a l u e i n t h e 2 0 0 t o 5 0 0 r a n g e . Wi t h t h e m o u s e , click on the left set of direction buttons to verify that the X and Y a x e s a r e m o v i n g . I n a l i k e m a n n e r, c l i c k o n t h e r i g h t m o s t u p a n d d o w n buttons to verify that the Z axis is moving. If all of these tests complete without any issues, you can be assured that your CNC machine i s w o r k i n g c o r r e c t l y. .
Note:One of the axis doesn’t move T h e X - a x i s a n d Z - a x i s a r e O k b u t t h e Y- a x i s d o e s n o t m o v e ? A:1.Check the connections; make sure it is plugged in correctly. 2.Check that the axis is not bending by turning the screw by hand (disconnect the router first). 3.Check that the grub screws on the coupler connecting the threaded rod to the stepper motor are tight and the coupler is not slipping. 4.If this doesn’t work Please swap the X axis motor and Y axis motor cables.
34 Note: All parameters(Size, depth, etc) have been completed when making the G file. Use Artcam, Inskcape, Fusion360, CopperCAM a n d o t h e r s o f t w a r e t o m a k e G f i l e s . L e a r n b y y o u r s e l f o n Yo u t u b e .
Part 5:LaserGRBL 1.Install lasergrbl software: (laser->Lasergrbl) Note: Make sure the dirver have install. ●Console window print ” Grbl 1.1f ['$' for help]” If the connection is successful. ●If the port selection is wrong, no information will be returned.
2. Click the jog to check if the machine move.(Make sure the wite buttons are press). If the jog does not turn green or Status is alarm, please click the lock button.
3.Raster image import Raster import allows you to load an image of any kind in LaserGRBL and turn it GCode instructions without the need of other software. LaserGRBL supports photos, clip art, pencil drawings, logos, icons and try to do the best with any kind of image. It can be recalled from “File, Open File” menu by selecting an image of type jpg, png or bmp.
How to adjust the power of the Module? Just adjust the speed and S-max value. Speed(take 3000mW as a example) 0-300 Cutting speed, suitable for cutting thin paper and wood chips. 500-800 ideal speed for engraving. Can carver craft paper, wood, leather(wallet), bamboo.
4.Start carving. (Please use a test board) Step 1: Click jog to move the moudle to the position you want to engrave. Step 2: Click on the zero-setting sign. Step 3: Click on the green triangle to start carving.
Note:If the carved picture is to the right than I expected There are two situations for the initially imported picture: 1. Have a distance from 0 point. 2. No distance from 0 point. Just reopen the picture and adjust the Offset parameter.
Note:If the focus is too scattered or the engraving effect is not ideal, you need to adjust the focus. Enter "M03 S50" in the input box to turn on the module, and rotate the Module head to adjust the focus to the minimum. After adjustment, enter M05 to turn off the module.
5.
1.Custom button Custom button is an additional function of lasergrbl, it is more convenient to operate.
Download path: Others---Online help---Lasergrbl official website--Custom Buttom---Download the installation package---Right-click on the blank space---Import the installation package 44 (1)The first is the role of reset (2)The third is that the current postion is the start pointing.
2. Default configuration Note:The system parameters are all default, please don't change them at will.
Part 6:Offline controller N o t e : W h e n u s i n g o f f l i n e c o n t r o l l e r, y o u n e e d t o u n p l u g t h e u s b c a b l e f r o m t h e c o m p u t e r, b e c a u s e o f f l i n e a n d c o m p u t e r c a n n o t b e u s e d t o g e t h e r. 1 .
2.Copy the NC file to offline controller Note: Using offline manual control to use the machine is equivalent to a p r i n t e r. I t i s o n l y c o m p a t i b l e w i t h G f i l e s .
3.Offline control connected to the control board 48 4 .
5.Interface introduction A.
B.
C.File Page A. File Page Note: Long press Exit/ Step for 3 seconds to exit the selection or stop the machine.
Part 7:Precautions Before operating your Desktop CNC Machine, please read the manual. Failure to do so may lead to damage to the CNC M a c h i n e o r p e r s o n a l i n j u r y. 52 ● Yo u m u s t b e 1 8 y e a r s o r o l d e r t o o p e r a t e t h i s m a c h i n e , u n l e s s s u p e r v i s e d b y a knowledgeable adult familiar with the machine. ● We a r t h e p r o p e r P e r s o n a l P r o t e c t i o n E q u i p m e n t ( S a f e t y G l a s s e s e t c . ) .
How to make a G-file How to install the limit switch If there are any problems when using our product, please contact our support team via xiaohua2018815@outlook.com.
