OPERATING INSTRUCTIONS SPEAKER SYSTEMS HS-1200BT, HS-1200WT, HS-1500BT, HS-1500WT

ManualsBrandsTOA Electronics ManualsPortable SpeakersHS-1500WT

OPERATING INSTRUCTIONS

SPEAKER SYSTEMS

1. SAFETY PRECAUTIONS ........................... 2

2. GENERAL DESCRIPTION ......................... 3

3. FEATURES ................................................. 3

4. DIMENSIONAL DIAGRAM ......................... 3

5. INPUT TERMINAL SECTION ..................... 4

6. IMPEDANCE CHANGE .............................. 4

7. ABOUT THE INPUT OVERLOAD

PROTECTION CIRCUIT ............................. 4

8. INSTALLATION .......................................... 5

9. EQUALIZING BY THE

DIGITAL SIGNAL PROCESSOR ............... 7

10. SPECIFICATIONS ...................................... 8

Accessories ................................................. 8

Optional products ........................................ 8

Thank you for purchasing TOA's Speaker System.

Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.

TABLE OF CONTENTS

日本語の取扱説明書は本書の裏面をご覧ください。

HS-1200BT

HS-1200WT

HS-1500BT

HS-1500WT

Summary of content (8 pages)

PAGE 1
日本語の取扱説明書は本書の裏面をご覧ください。 OPERATING INSTRUCTIONS SPEAKER SYSTEMS HS-1200BT HS-1200WT HS-1500BT HS-1500WT TABLE OF CONTENTS 1. SAFETY PRECAUTIONS ........................... 2 8. INSTALLATION .......................................... 5 2. GENERAL DESCRIPTION ......................... 3 9. EQUALIZING BY THE DIGITAL SIGNAL PROCESSOR ............... 7 3. FEATURES ................................................. 3 4. DIMENSIONAL DIAGRAM ......................... 3 5. INPUT TERMINAL SECTION ..............
PAGE 2
1. SAFETY PRECAUTIONS • Before installation or use, be sure to carefully read all the instructions in this section for correct and safe operation. • Be sure to follow all the precautionary instructions in this section, which contain important warnings and/or cautions regarding safety. • After reading, keep this manual handy for future reference.
PAGE 3
CAUTION Indicates a potentially hazardous situation which, if mishandled, could result in moderate or minor personal injury, and/or property damage. When the Unit is in Use • Do not place heavy objects on the unit as this may cause it to fall or break which may result in personal injury and/or property damage. In addition, the object itself may fall off and cause injury and/or damage. • Make sure that the volume control is set to minimum position before power is switched on.
PAGE 4
5. INPUT TERMINAL SECTION • As the Speakon connector is internally connected in parallel to the screw terminal as shown below, you can use either of the two. • The usable connector (on the cable end) that matches the NEUTRIK NL4MP Speakon is NEUTRIK NL4FX Speakon. • Input terminal connection diagram is as shown below. [Input terminal connection diagram] [Rear] Speaker Speaker Screw terminal Speakon Screw terminal 6.
PAGE 5
8. INSTALLATION 8.1. Installing to a Ceiling or Wall Install the speaker system to a ceiling or wall using the optional mounting brackets shown below. Note Refer to the instruction manual enclosed with the HY-1200 series or HY-1500 series Mounting Bracket for its mounting details. 8.1.1. HY-1200VB, HY-1200VW, HY-1500VB and HY-1500VW Mounting Brackets (For vertical speaker mounting) • These brackets are designed to mount HS series speakers to ceilings or walls vertically.
PAGE 6
8.1.4. HY-W0801 and HY-W0801W Wall Mount Brackets (For wall installation, horizontal angle adjustable) Wall Mount Bracket Installing the HS series speaker to a wall in conjunction with the HY-1200 series or HY-1500 series Mounting Bracket permits the speaker's horizontal angle to be adjusted. Mounting Bracket The figure at right shows an example of vertical speaker installation. 8.1.5.
PAGE 7
8.3. Using as a Floor Monitor Notes • When installing the speaker system on slippery floor, put a non-slip mat under the speaker. • Do not kick or stand on the speaker system, as this will damage the speaker. The figure shows the HS-1200 series. 8.4. Attaching the Supplied Rubber Feet Attach the rubber feet in the case of speaker storage or on-floor speaker installation. Datum line Note The rubber foot has a direction (back and forth).
PAGE 8
10. SPECIFICATIONS Model No. Enclosure Rated Power Rated impedance Sensitivity Frequency Response Crossover Frequency Directivity Angle Speaker Component Input Terminal Enclosure Finish Punched net Operating Temperature Dimensions Weight HS-1200BT HS-1200WT HS-1500BT HS-1500WT Sealed type Continuous pink noise: 100 W, Continuous program: 300 W 8Ω 100 V line: 170 Ω (60 W), 330 Ω (30 W), 670 Ω (15 W) 70 V line: 83 Ω (60 W), 170 Ω (30 W), 330 Ω (15 W), 670 Ω (7.