ENGLISH QUICK MANUAL COMBINATION CAMERA OUTDOOR COMBINATION CAMERA TABLE OF CONTENTS MENU SCREEN CONFIGURATION·························2 FUNCTION TABLE Preset C-CC514, C-CC564 C-CC574, C-CC714 C-CC764, C-CC774 Manual ······································································12 Maintenance ····························································12 HOW TO SETTING ···································································4 1.
MENU SCREEN CONFIGURATION CAMERA MENU →PRESET ID SETTING CAMERA SETTING CAM AUTO MODE ALARM AUX TIMER MANUAL MAINTENANCE LANGUAGE ENGLISH *PRESET* →MEMORY READJUST ALL POS ***POS MEMORY RESET MEMORY ALL RESET NO AUTO RETURN OFF HOME 1POS PRESET FREEZE OFF *ID SETTING* →DISPLAY ID SETTING LOCATION FRAME ADJUST ZERO POINT *CAMERA SETTING* →WHITE BALANCE ATW R---*---B BACKLIGHT OFF BRIGHTNESS ----*---DAY/NIGHT NORMAL AUTO FOCUS ONE PUSH AGC AUTO SLOW SHUTTER x32 SHUTTER SPEED NORMAL NEXT PAGE *AUTO MODE* →AU
FRONT PAGE *ALARM* →INPUT REPORT ACTIVE STATE PRIORITY ACTION INTERVAL RESET ACTION ALARM DATA *AUX* ----------------------------------------→AUX1 AUX2 *TIMER* →PROGRAM TIME DISPLAY DATE DISPLAY ENTER TIME ENTER DATE SUMMER TIME 12H MM/DD/YY *MANUAL* →ZOOM SCALABLE P/T P/T LIMIT P/T LIMIT SETTING MAX P/T SPEED FLIP UP LIMIT *MAINTENANCE* PASSWORD 1111 ↑ OFF ON OFF LEFT 120 OFF ON *MAINTENANCE* →INITIALIZE REFRESH PASSWORD MOTOR POWER FACTORY PRESET AUTO ADJUST DATA BACKUP NEXT PAGE NO ON OFF NO OF
FUNCTION TABLE Commands Keystrokes Description PRESET MEMORY POS 1-255 - FINE SETTING Settings such as camera direction, lens angular field of view, and focus can be preset in advance. Up to 255 positions can be set. This function simultaneously resets all preset camera panning positions. READJUST ALL POS POS 1-255 The deviation of one camera position is measured, based on which all other positions are globally corrected.
ANGLE OFF/ON/1s/3s/5s/10s ZOOM OFF/ON/1s/3s/5s/10s DATE OFF/ON/1s/3s/5s/10s TIME OFF/ON/1s/3s/5s/10s Displays the coordinate. Pan (0 to 359°)/ Tilt (5 to -185°) fixed 8 characters. [ ***/-*** ] Pan angle (0 to 359°)/ ±Tilt (5 to 185°) Displays the Electronic Zoom. Fixed 3-charactors. Displays the date in accordance with the date setting (timer setting) format. Fixed 8-charactors. Displays the time in accordance with the time (hour, minute) setting (timer setting) format.
The Backlight Compensation function makes the image displayed on the screen easier to see when there is strong light behind the subject. (factory default: OFF) OFF : Turns the Backlight Compensation function off. This is the setting usually used. WIDE DYNAMIC : Allows backlight compensation that prevents the subject from becoming too dark or the surrounding background from becoming too white. Try using WIDE DYNAMIC as the initial setting to compensate for BACKLIGHT OFF/WIDE DYNAMIC (*1)/ backlighting.
(Factory default: ONE PUSH) ONE PUSH: Auto focusing is operated when the Auto-focus key is pressed. STOP AF : Auto focusing is automatically operated after the camera scene or angle of view has been changed. The STOP AF function does not work AUTO FOCUS ONE PUSH/STOP AF/ when the Focus key is used. Pressing the Auto-focus key again will put the CONTINUOUS camera in the STOP AF mode. CONTINUOUS: The Auto-focus function is always operated.
The camera’s sync system can be switched to the system that uses the power frequency. It is also possible to adjust the phase. (Factory default: INT.) INT: Represents the internal sync system. Select this setting when only a single camera is used and it is not necessary to synchronize it with other SYNC INT/LL – NT60Hz:00-82/PL50Hz:00-99 camera. LL : Represent the power sync system. Select this setting when synchronizing 2 or more cameras using the power frequency.
AUTO MODE One of the following 5 automatic functions can be assigned to the Auto key: (factory default: AUTO PAN) AUTO PAN: Auto Pan operation begins when the Auto key (or Auto Pan key) is pressed. AUTO KEY AUTO PAN/SEQUENCE/ TRACE1-2/TOUR1-16 SEQ : Sequence operation begins when the Auto key (or Auto Pan key) is pressed. TRACE1 : Trace 1 operation begins when the Auto key (or Auto Pan key) is pressed. TRACE2 : Trace 2 operation begins when the Auto key (or Auto Pan key) is pressed.
The Preset Sequence function displays set positions of one same camera SEQUENCE on the monitor in predetermined sequential order. Sets the sequence order. (factory default: Normal) NORMAL: Playbacks preset-memory stored camera positions in numerical order. MODE NORMAL/RANDOM/TEST RANDOM: Playbacks preset memory store camera positions in random order. The stop duration for each position is determined in random order. TEST : Playbacks preset-memory stored camera positions in numerical order.
Specify whether to display the set alarm ID on the screen and forcibly execute alarm operation or give priority to operation when an alarm signal is number 1-8: PRIORITY ALARM/MANUAL/TIMER – 3s/5s/10s/15s/20s/30s/ 45s/1min received. ALARM : Ignores commands from the controller and starts alarm operation. MANUAL : Initiates alarm operation only while operating the initial program. TIMER : Initiates alarm operation after the preset time elapses.
Enables summer time between 2:00 AM on the set first day of summer time and 2:00 AM on the last day. SUMMER TIME OFF/ON/SET - FIRST DAY/LAST DAY OFF: Disables summer time. ON : Enables summer time. SET: Performs summer time setting. MANUAL ZOOM SCALABLE ON/OFF P/T Rotation speed relative to zoom ratio can be set to OFF. Select OFF when the function of reducing the rotation speed during telescopic operation is not needed. Designate the pan and tilt rotation range limits.
If the camera is used for long uninterrupted periods of time, the camera position may deviate when the position is played back. In such cases, deviation can be corrected using the auto-refresh function. Also, if the camera’s horizontal rotation contacts get dirty, the displayed image may REFRESH OFF/EVERY/SUN-SAT become distorted or manual horizontal rotation interrupted. In such cases, the auto-refresh function cleans horizontal rotation contacts periodically. OFF : Not refreshed.
Set locations for motion detection sensors. FUNCTION AREA1-8 OFF : No movement detected. OFF/ON-L/ON-M/ON-H ON–L: Detects movement at low sensitivity. ON–M: Detects movement at intermediate sensitivity. ON–H: Detects movement at high sensitivity. Set operations that will take place when sensors are activated. AREA1-8 OFF/***POS/TOUR1-16/ ACTION TRACE1-2/ALARM1-8/ AUX1 ON/AUX1 OFF/ AUX2 ON/AUX2 OFF OFF : No operation. ***POS : Presets to the designated position.
HOW TO SETTING 1. BEFORE SETTING 1.1. Address Display When Turning Power On When the camera’s power is turned on, the camera performs the initial operation (initializing operation) and simultaneously the camera address appears on the monitor. After the completion of initial operation and peripheral device connections, the camera can be controlled and the camera address screen will disappear. CAMERA ADDRESS*** Notes • In the place of “***”, a camera address such as “001” will be displayed.
1.3. Setting Basic Operation Menu screen to be displayed and the operation slightly differ depending on the connected equipment, however there is no difference in basic operation. More particularly, refer to the instruction manual, operation manual or set up manual enclosed with each equipment. Menu key • Use the Menu Start switch to enter the menu screen or exit the menu screen. • Press the Menu Start switch to exit the menu screen in any screen status.
2. ENTERING CAMERA MENU SCREEN 1. Press the Menu key. (When a password is required, enter it with the numerical keypad.) The menu screen is displayed on the remote controller’s liquid crystal display. 2. With the joystick, select “CAMERA MENU” and press the Set key. The display is placed in the standby mode for the entry of a camera number to call up the camera menu. Menu OPERATION MODE CAMERA MENU * * *CH 3. Enter the camera number with the numerical keypad, and press the Set key.
3. SELECTING THE LANGUAGE The language to be displayed on the screen can be selected among English, German, French and Italian. (Factory default: English) 1. Select "LANGUAGE" on the Camera Menu screen with the joystick, then press the Set key. he arrow (→) moves to “ENGLISH” (factory default). 2. Select "ENGLISH," "DEUTSCH," "FRANÇAIS," or "ITALIANO" with the joystick, then press the SET key. The screen switches to the Menu screen of the selected language.
4. SETTING PRESETS Settings such as camera direction, lens angular field of view, and focus can be preset in advance. Up to 255 positions can be set. 4.1. Entering Presets into the Memory Note Positions cannot be preset in the electronic zoom range or in flip mode. Presetting is possible only for parts other than the electronic zoom or when the Flip function has been disabled.
4. Press the Set key. The position setting screen (the selected camera image) is displayed. ***-*** SETTING Note “*** – ***” on the first line of the Setting screen indicates the camera number on the left and the position number on the right. 5. Operating the joystick, Zoom key, and Focus key, move the camera to the desired position, then press the Set key. 6. Operate the joystick, Zoom key, and Focus key further more to fine adjust, then press the Set key.
5. MAINTENANCE SETTINGS This menu is used to control functions as well as to display information required during installation or maintenance. 1. Select “MAINTENANCE” on the Camera Menu screen, then press the Set key. 2. Change the portion pointed by the arrow (↑) with the password ( figures) with the joystick, then press the Set key. The arrow (↑) moves to place to the right.
Ver. 1.