Owner's manual

ManualsBrandsToa ManualsAcousticsSR-L05

OPERATING INSTRUCTIONS

SPEAKER SYSTEM

SR-F09, SR-F09-V1

SR-F09-V2, SR-F09-V3

SR-L09, SR-L05

Thank you for purchasing TOA's Speaker System.

Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.

TABLE OF CONTENTS

1. SAFETY PRECAUTIONS ................................................................................. 2

2. GENERAL DESCRIPTION .............................................................................. 3

3. FEATURES ........................................................................................................... 3

4. DIMENSIONAL DIAGRAM .............................................................................. 4

5. WIRING DIAGRAMS ......................................................................................... 4

6. INPUT CONNECTORS ..................................................................................... 5

7. CONNECTIONS .................................................................................................. 5

8. FLYING ................................................................................................................... 6

9. DIGITAL PROCESSOR SETTINGS ............................................................. 7

10. SPEAKER STAND FOR SR-F09 AND SR-F09-V1 .................................. 8

11. CHANGE FROM SINGLE- TO BI-AMPLIFIER DRIVE ........................... 9

12. SPECIFICATIONS ............................................................................................ 12

Accessory ................................................................................................................ 12

Summary of content (12 pages)

PAGE 1
OPERATING INSTRUCTIONS SPEAKER SYSTEM SR-F09, SR-F09-V1 SR-F09-V2, SR-F09-V3 SR-L09, SR-L05 TABLE OF CONTENTS 1. SAFETY PRECAUTIONS ................................................................................. 2 2. GENERAL DESCRIPTION .............................................................................. 3 3. FEATURES ........................................................................................................... 3 4. DIMENSIONAL DIAGRAM ............................................
PAGE 2
1. SAFETY PRECAUTIONS • Before installation or use, be sure to carefully read all the instructions in this section for correct and safe operation. • Be sure to follow all the precautionary instructions in this section, which contain important warnings and/or cautions regarding safety. • After reading, keep this manual handy for future reference.
PAGE 3
2. GENERAL DESCRIPTION The SR-F09, SR-F09-V1, SR-L05, and SR-L09 are designed for on-the-road applications, while the SR-F09V2 and SR-F09-V3 are designed for permanent installation. They are all high-power, high quality speaker systems that can stand up. 3. FEATURES • The SR-F9, SR-F09-V1, SR-F09-V2, and SR-F9-V3 have an internal passive network and are driven by a single amplifier. (This can be changed to bi-amplifier drive by changing their internal connector connections.
PAGE 4
. DIMENSIONAL DIAGRAMS [SR-F09-V2, SR-F09-V3] [SR-F09, SR-F09-V1] 221 195 195 46 390 364 16-W3/8'' Nut 364 315 315 619 619 390 A 160 30° 155 120 Center of gravity Center of gravity 155 224 The side as viewed from the direction of arrow A 161 160 46 221 ° 161 30 2-M8 Nut Flying fitting (4 places) [SR-L09] [SR-L05] 606 502 452 629 629 829 Unit: mm 5.
PAGE 5
6. INPUT CONNECTORS • The figures below show each speaker's input configuration. Because the connector is internally connected in parallel to the screw terminal, you can use either of the two. [SR-F09, SR-F09-V1, SR-F09-V2, SR-F09-V3] [SR-L09] [SR-L05] • Pins of the Neutrik connector are connected as shown in the table below. Pin No.
PAGE 6
8. FLYING WARNING Be sure to refer flying construction work to the dealer from whom the speaker was purchased. 8.1. SR-F09 and SR-F09-V1 Shown below are the general flying methods: Never suspend as illustrated below: • Flying through only one suspension point on the top panel. • Vertical suspension of more than 3 speakers. • Flying with a single looped wire • Flying through handles. [Precautions] • Two flying fittings are provided on each of the top and bottom panels.
PAGE 7
9. DIGITAL PROCESSOR SETTINGS [Bi-amplifier drive for SR-F09+SR-L09/L05] Channel SR-L09 SR-F09 LOW Gain (dB) Polarity +5.0 NORMAL 0 X-over Combination Filter HPF/LPF TYPE Freq. (Hz) HPF (24dB) LinkwitzRiley 20 LPF (24dB) LinkwitzRiley 80 HPF (24dB) LinkwitzRiley 100 LPF (24dB) LinkwitzRiley 1.0k NORMAL HPF (24dB) LinkwitzRiley TYPE Freq. (Hz) Gain (dB) Q Delay (msec) 0.667 PEQ 40 +2.5 4.318 PEQ 160 +5.0 1.414 PEQ 580 −3.5 2.079 PEQ 3.15k −4.0 3.633 PEQ 11.
PAGE 8
10. SPEAKER STAND FOR SR-F09 AND SR-F09-V1 The speaker stand manufactured by Köning & Meyer GmbH (K & M) of Germany is made available for use with TOA's SR-F09 and SR-F09-V1 speakers. The speaker stand consists of a Stand and a Stand Bracket, which are sold separately. In addition, separately prepare 2 speaker mounting screws to secure the bracket to the speaker. Stand: Model 213 Bracket: Model 19580 Speaker mounting screw: M8 x 20 10.1. USAGE (Refer to Fig. 1.) (Fig. 1) 1.
PAGE 9
CAUTION • Only use the stand on the flat, hard ground or floor surfaces. • Avoid installing the stand in the passage where people could trip over the tripod legs. • When using the stand outdoors, avoid locations exposed to strong winds. • To minimize the chance of the stand toppling over, avoid extending the stand too high. • When the stand could fall down, be sure to secure it with guy wires or other devices. 11.
PAGE 10
11.1.2. SR-L09 1. Remove front grille fixing screws (12 places) to remove the front grille. 2. Remove the woofer located on the right hand side as viewed from the front by removing eight screws. 3. Disconnect connectors inside an enclosure. Front grille fixing screw Connector 4. Connect a connector having a marker on it to a similarly-marked connector. Front grille Marker 5. Replace the woofer using screws. 6. Replace the front grille using the front grille fixing screws. Connector Woofer removed.
PAGE 11
• Pins of the Neutrik connector are connected as shown in the table below. Pin No. 1 + 1 2 + 2 - SR-F09, SR-F09-V1, SR-F09-V2, SR-F09-V3 LOW + LOW HIGH + HIGH - SR-L09 Left* + Left Right + Right - * The "left" and the "right" are the directions as viewed from the front. • Because the connector is internally connected in parallel to the screw terminal, you can use either of the two. 11.3.
PAGE 12
. SPECIFICATIONS Model No.