OWNER’S MANUAL ●Four suspension ●Swing function ( optional) ●USB, MP3, TF card Jack ●Two opening doors ● Leather seat cover ( optional) ●Rubber wheels ( optional) ●Maximum user weight:30 KGS WARNING ●Must be assembled by an adult! ●Read and understand this entire manual before using! ●Before first time use, charge the battery for at least 4-6 hours. ●Please keep this manual well for reference in the future.
Table of Contents 1.Specification 2.Structure chart 3.Assembly steps 4.How to operate your “Ride on” 5.How to use Controller 6.Charging the battery 7.Trouble shooting guide 8.Maintaining your “ride on” 9.Wiring diagram 10.Disclaimer Specification Thanks for purchasing our products, we hope your children enjoy this product for years to come. Keep these points in mind as you read this guide: Suitable age: 3-8 years Power way: Rechargeable Load capacity: 30KGS Battery:6V 4.5Ah, 12V 4.
Structure chart Item Name Picture Qty.
7 Wheels cover 8 motors 4 6V 4.5Ah battery one motor 12V 4.
Assembly steps car bodymotorsaxle sleeve④wheel ⑤gasket⑥nut⑦wheels cover 9 seat ○ 10 windshield ○ 11 M10 nut, M5*35 round screw ○ 12 steering wheel ⑧mirror ○ Warning The toy should be used with caution since skill is required to avoid falls or collisions causing injury to the user or third parties. ●The vehicle must be assembled by adults, which needs about 10 minutes.
(2pieces check in the spare bags) ●Don’t let children touch or play the small components so as to avoid children being chocked. ●Please check the packing list before assembling. Deal with the plastic bags properly and don’t let children play the bags so as to avoid them being choked. Driving wheel installation: ●Turn the bottom of the toy car up as above picture show. ●Put a axle sleeve and a gasket into the wheel. ●Push the wheel to the back axle and make the wheel connect well with the motor.
●Turn the bottom of the toy car up as above picture show. ●First put a axle sleeve and a gasket into the wheel. ●Push the wheel to the front axle. ●Put a axle sleeve and a gasket, then tighten them with a nut. ● Insert the Wheels cover. ●The other wheel to be installed as the same way. Driving wheel installation ●Connect the terminal of the steering wheel to terminal of the instrument panel , put the wire back to instrument panel if they are too long.
● Make the slots in the mirror in the same line with the slots in car boy and press the mirrors into the gaps. Windshield installation ●Check the slot and press the windshield according the slot location to the gap end.
● Put the seat onto the car body according to above picture, and tight the seat with slots well using Ø4*20 self tapping screw.
● Take off the black plastic protective jacket. Connect the red line on the car body connect with the red line of battery. Note： Pay attention to the positive and negative positions to prevent short circuit of the power supply. How to operate your“Ride on” ●Please tell your children and his playmates with the following safety rules and make sure they all understand. ●The car should be driven under the supervision of adults ●When driving, must wear a helmet and wear shoes and must sit on the seat.
●Check the vehicle’s wires and connections, do not change the original design. Player: with USB, MP3, TF card Jack, powder quantity display. Light switch: Turn on or off the light. Powder button: to turn on or off the powder. ④Forward/backward switch:Operate it together with the accelerator to make the vehicle to go forward/backward. When the ride on toy car is out of powder, you can push it home with the help of small wheels and handle.
How to use Controller WARNING Non-rechargeable batteries are not to be recharged; Different type of batteries or new and used batteries are not to be mixed; Batteries are to be inserted with the correct polarity; Exhausted batteries are to be removed from the toy; The supply terminals are not to be short-circuited. Rechargeable batteries are only to be charged under adult supervision; ●Open the battery cover on the back of the remote control and load two 1.
●Press the code button for about 10 seconds and open the vehicle powder to make the controller connect with the vehicle. ●Just first time need this step, in the future using no need. ●Turn the “remote control/ foot switch” on the vehicle to “remote: position. ●Press the remote control “forward” button, make the vehicle go forward. Without operation the remote control, the car will stop moving.
3. Are the wires welded well on the ends If no, weld well. of motor If yes, check the next. 4. Take apart the plug-in of the motor If still not work, change the and connect with the battery directly motor. If work, driving circuit board need professional repair, please contact with your supplier. The vehicle cannot move forward or backward 1. Check the forward/backward switch If no, change the switch. with a muti meter and see if it is normal If yes, check the next. The vehicle moves slowly 1.
Maintaining your “ride on” ●Parents should check the vehicle’s main parts are all in good condition before each time your kids driving. To check whether the charger, plug, vehicle shell are broken or not and whether the bolts are loose or not. If there are something wrong please repair it before using. ●After driving for a while, please wipe some lube on the iron parts to prevent getting rusty. Keep away from fire and the sun for a long time.
●In order to improve the quality, we may change some parts of the structure or its appearance without notice in advance, hope you understand and support. ●This manual is very important, please take care of.
