User's Manual
Table Of Contents
- 1 Safety and Compliance
- 1.1 Safety and Usage
- 1.1.1 Usage Warning
- 1.1.2 Emergency Warning
- 1.1.3 Child Safety
- 1.1.4 Infrared Warning
- 1.1.5 Epilepsy Warning
- 1.1.6 Mechanical Shock Warning
- 1.1.7 Bending Warning
- 1.1.8 Do not open the devices
- 1.1.9 Connectors
- 1.1.10 HDMI Cable Warning
- 1.1.11 Environment
- 1.1.12 Battery Warning
- 1.1.13 Wireless Warning
- 1.1.14 Transportation
- 1.1.15 Accessories
- 1.1.16 Cleaning
- 1.1.17 Disposal
- 1.2 Compliance Information
- 1.3 Other limitations and considerations
- 1.3.1 Intended use
- 1.3.2 SD memory cards
- 1.3.3 Multiple connections between Glasses Controller Software and Recording Unit
- 1.3.4 Eye movement classification
- 1.3.5 Light conditions
- 1.3.6 Eyelashes
- 1.3.7 Droopy eyelids
- 1.3.8 Eye glasses and contact lenses
- 1.3.9 WLAN connectivity
- 1.3.10 Power
- 1.3.11 Keeping Tobii Glasses Controller Software and the Recording Unit firmware up to date
- 1.1 Safety and Usage
- 2 Introduction
- 3 Installing and Updating Tobii Glasses Controller Software
- 4 Updating the Tobii Glasses Recording Unit firmware
- 5 Getting to know Tobii Glasses 2
- 6 Workflow Quick Guide
- 7 Basic Operations with Tobii Glasses 2
- 7.1 Setting up Tobii Glasses 2 hardware
- 7.1.1 Charging Recording Unit batteries
- 7.1.2 Inserting/removing the battery – Glasses Recording Unit
- 7.1.3 Inserting/removing an SD memory card in the Recording Unit
- 7.1.4 Connecting the HDMI cable
- 7.1.5 Changing nose pads (remove and mount new):
- 7.1.6 Changing the lenses on the Head Unit
- 7.1.7 Turning Tobii Glasses 2 on and off
- 7.2 Managing study data in Tobii Glasses Controller Software
- 7.3 Connecting the Tablet running Tobii Glasses Controller Software to a Recording Unit
- 7.4 Fitting the Tobii Glasses 2 Eye Tracker onto a participant for recording
- 7.5 Recording with Tobii Glasses 2
- 7.6 Watching a recording live with the Live Viewer
- 7.7 Locating recordings
- 7.8 Replaying a recording
- 7.9 Exporting a gaze replay video
- 7.10 Deleting a recording
- 7.11 Backing up recorded data
- 7.12 Other operations and information
- 7.13 Tobii Glasses Controller Software considerations and limitations
- 7.1 Setting up Tobii Glasses 2 hardware
- 8 Advanced Usage with Multiple Units
- 9 Accessories
- Appendix A Technical Specifications
- Appendix B Calibration target
7.1.2 Inserting/removing the battery – Glasses Recording Unit
Only use the supplied rechargeable Li–ion batteries (type
18650, 4.2 Volts) in the Recording Unit.
To insert a battery into the Tobii Glasses Recording
Unit (See illustration to the right):
1. Turn off the Recording Unit.
2. Push and turn the bottom of the Recording Unit and then
lift the battery compartment lid.
3. Remove any old battery and insert a new one. When in-
serting a new battery, make sure to turn the battery so
that the positive end (+) is at the top of the Recording
Unit and the negative end (-) is against the bottom.
4. Put the battery container lid back on and lock it by push-
turning it.
Never insert batteries the wrong way in the Recording Unit as this may damage the device. The battery should be in-
serted with the positive end (+) at the top of the Recording Unit and the negative end (-) against the bottom.
Never insert any other type of batteries than the supplied Li–ion batteries (type 18650, 4.2 Volts) in the Recording
Unit as this may damage the device permanently.
7.1.3 Inserting/removing an SD memory card in the Recording Unit
To insert an SD memory card into the Tobii Glasses Recording Unit (See illustration above):
1. Tap the Eject symbol on Tobii Glasses Controller Software Dashboard for the relevant Recording Unit.
2. Tap Yes in the dialog box to confirm.
3. Open the SD memory card lid of the Recording Unit.
4. To release the SD memory card gently press the SD memory card inside the Recording Unit. Remove the SD memory
card.
5. Gently insert a new SD memory card into the SD memory card slot with the contacts facing upward (towards the same
side as the Tobii logo on the side of the Recording Unit).
6. Close the SD memory card lid.
Never remove the SD card from the Glasses 2 Recording Unit while a recording is ongoing as doing so will corrupt
any data being recorded.
The Recording Unit only supports SD memory cards formatted as FAT32. Make sure to format any new SD memory
cards as FAT32 before inserting them in the Recording Unit. New SDXC SD memory cards must always be formatted
as FAT32 before they will work with the Recording Unit.
20
7 Basic Operations with Tobii Glasses 2
Tobii Glasses 2 Eye Tracker User’s manual v.1.0.2 - en-US