User's Manual
Table Of Contents
- 1 Safety and Compliance
- 1.1 Safety and Usage
- 1.1.1 Usage Warning
- 1.1.2 Emergency Warning
- 1.1.3 Child Safety
- 1.1.4 Infrared Warning
- 1.1.5 Epilepsy Warning
- 1.1.6 Mechanical Shock Warning
- 1.1.7 Bending Warning
- 1.1.8 Do not open the devices
- 1.1.9 Connectors
- 1.1.10 HDMI Cable Warning
- 1.1.11 Environment
- 1.1.12 Battery Warning
- 1.1.13 Wireless Warning
- 1.1.14 Transportation
- 1.1.15 Accessories
- 1.1.16 Cleaning
- 1.1.17 Disposal
- 1.2 Compliance Information
- 1.3 Other limitations and considerations
- 1.3.1 Intended use
- 1.3.2 SD memory cards
- 1.3.3 Multiple connections between Glasses Controller Software and Recording Unit
- 1.3.4 Eye movement classification
- 1.3.5 Light conditions
- 1.3.6 Eyelashes
- 1.3.7 Droopy eyelids
- 1.3.8 Eye glasses and contact lenses
- 1.3.9 WLAN connectivity
- 1.3.10 Power
- 1.3.11 Keeping Tobii Glasses Controller Software and the Recording Unit firmware up to date
- 1.1 Safety and Usage
- 2 Introduction
- 3 Installing and Updating Tobii Glasses Controller Software
- 4 Updating the Tobii Glasses Recording Unit firmware
- 5 Getting to know Tobii Glasses 2
- 6 Workflow Quick Guide
- 7 Basic Operations with Tobii Glasses 2
- 7.1 Setting up Tobii Glasses 2 hardware
- 7.1.1 Charging Recording Unit batteries
- 7.1.2 Inserting/removing the battery – Glasses Recording Unit
- 7.1.3 Inserting/removing an SD memory card in the Recording Unit
- 7.1.4 Connecting the HDMI cable
- 7.1.5 Changing nose pads (remove and mount new):
- 7.1.6 Changing the lenses on the Head Unit
- 7.1.7 Turning Tobii Glasses 2 on and off
- 7.2 Managing study data in Tobii Glasses Controller Software
- 7.3 Connecting the Tablet running Tobii Glasses Controller Software to a Recording Unit
- 7.4 Fitting the Tobii Glasses 2 Eye Tracker onto a participant for recording
- 7.5 Recording with Tobii Glasses 2
- 7.6 Watching a recording live with the Live Viewer
- 7.7 Locating recordings
- 7.8 Replaying a recording
- 7.9 Exporting a gaze replay video
- 7.10 Deleting a recording
- 7.11 Backing up recorded data
- 7.12 Other operations and information
- 7.13 Tobii Glasses Controller Software considerations and limitations
- 7.1 Setting up Tobii Glasses 2 hardware
- 8 Advanced Usage with Multiple Units
- 9 Accessories
- Appendix A Technical Specifications
- Appendix B Calibration target
7.1.6 Changing the lenses on the Head Unit
Glasses 2 comes with two different protective lenses, one clear and one tinted. The tinted lens is intended to be used in bright
or sunny environments, while the clear lens is intended for general use. Glasses 2 will function even though no lens is attached
to the Head Unit.
1. Locate the small hook that keeps the lens in place, located between the scene camera and the nose pad at the front of
the Tobii Glasses Head Unit.
2. To remove the existing lens: Gently push the hook downwards while gently turning the lens past the retaining clip.
3. To mount a lens: Fit the position guides into the indentations, and then gently press the lens past the retaining clip so
that it locks in place.
7.1.7 Turning Tobii Glasses 2 on and off
To turn on the Tobii Glasses 2 Eye Tracker (implies
that the Recording Unit is turned off):
1. Make sure the eye tracker is fully assembled according
to the instructions above.
2. On the Recording Unit, press and hold the power button
for approximately 3 seconds (until the Connection Sta-
tus LED and the SD card Activity LED flash green to in-
dicate startup.)
To turn off the Tobii Glasses 2 Eye Tracker (Implies
that Recording Unit is turned on):
• On the Recording Unit, press and hold the power button
for at least 4 seconds.
• During these 4 seconds, before the actual shutdown
process begins, the Connection Status LED and the SD
card Activity LED flash yellow to indicate that the Re-
cording Unit is about to start the shutdown process.
• When the Connection Status LED and the SD card Ac-
tivity LED turn bright yellow, the shutdown process be-
gins and the button can be released.
7.2 Managing study data in Tobii Glasses Controller Software
7.2.1 Creating a new study
When a new study is created, a new file container for participants and recordings is created automatically. Participants and re-
cordings are not shared among studies.
To create a new study:
1. Tap Studies.
2. Tap Create New Study in the lower right hand corner.
3. Type a name for your study in the Create New Study dialog box.
4. Tap Create.
7.2.2 Adding participants to a study
Participants can be added to a study in two different ways — either as a part of creating a recording (see section 7.5 Recording
with Tobii Glasses 2, page 27), or through the Participants List (see below). If participants' names or identification codes are
22
7 Basic Operations with Tobii Glasses 2
Tobii Glasses 2 Eye Tracker User’s manual v.1.0.2 - en-US