Installation Guide

Important Informaton - Read before beginning installation
Warning - Risk of re or electric shock. LED Retrot Kit installation requires knowledge of
luminaires electrical systems. If not qualied, do not attempt installation.
Warning - Risk of re or electric shock. Install this kit only in the luminaires that have the
construction features and dimensions shown in the photographs and/or drawings.
Warning - To prevent wire abrasion, do not expose wiring to edges of sheet metal or other
sharp objects.
Warning - To avoid potential re or shock hazard, do not use this retrot kit in luminaires
employing shunted bi-pin lampholders.
Warning - This xture must be grounded and installed in accordance with local and national
electrical codes, by a person familiar with the construction and operation of the product and
the hazards involved.
Do not make or alter any open holes in an enclosure of wiring or electrical components
during kit installation. Installers should not disconnect existing wires from lampholder
terminals to make new connections at lampholder terminals. Instead installers should cut
existing lampholder leads away from the lampholder and make new electrical connections
to lampholder lead wires by employing applicable connectors.
This retrot process does not change the environmental rating of the xture being
retrotted. For damp or wet location placements, the xture needs to be rated as such.
This device is intended for indoor use or weather protected xtures only. Do not use where
directly exposed to water or water spray.
This devices is not intended for use with emergency exits.
Installation
IMPORTANT - Installation of toggled LED tubes requires modication of the wiring within the existing uorescent xture. Please read
the entire installation instructions before beginning your installation.
Please examine all parts that are not intended to be replaced by the retrot kit for damage and replace any damaged parts prior to
installation of the retrot kit.
Before Retrot: After Retrot:
2. Remove existing uorescent tubes and ballast cover.
3. Cut all wires attached to the ballast(s).
Wires should be cut as close to the ballast as
possible as you will be reusing them later.
1. Turn off power to the uorescent xture(s) at the circuit breaker.
Included:
(1) toggled LED tube (Model: D416-XX311, D416-XX321, D312-XX321, D208-XX321)
(1) Fixture Modication Label
(2) Wire nuts
(2) Non-shunted lampholders
FCC Notice
This device complies with Part 15 of the FCC Rules and with Industry
Canada license-exempt RSS Standards. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in an installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for
help.
Changes or modications not expressly approved by toggled could
avoid the user’s authority to operate the equipment.
This equipment complies with FCC radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed
and operated with minimum distance 20cm between the radiator
and your body.
toggled LED tubeFluorescent Tube
Line (Hot) Line (Hot)
Neutral
BALLAST BALLAST
Neutral
toggled LED tubeFluorescent Tube
toggled LED tubeFluorescent Tube
toggled LED tubeFluorescent Tube
1.844.864.4533 [e-mail] See toggled.com/warranty for details. Installation video: www.toggled.com/installation
BALLAST
D Series Installation Instructions
11-01718-AG
Watch installation video
www.toggled.com/installation