Installation Guide

11-01768-AB / 2017-02-01
Fixtures may contain one or more lamps. See the table
below about intended retrofit fixtures and quantities
(E416, E312, E208)
INSTALLATION
INSTRUCTIONS
Conversion from ballast
to direct AC power
INSTRUCCIONES
DE INSTALACIÓN
Conversión de balasto a
alimentación de CA directa
DIRECTIVES
D’INSTALLATION
Passage du ballast à
l’alimentation CA directe
164 Indusco Court
Troy, Michigan 48083-4641 USA
1-844-toggled
[e-mail]
toggled.com
IMPORTANT! Installation of toggled LED tubes requires modication of the wiring
within the existing uorescent xture. Please follow the specic instructions below.
If you have any questions or comments, please feel free to contact 1-844-toggled.
THIS KIT INCLUDES:
(1) Installation Instruction Booklet
(1) toggled LED lamp (E416, E312, E208)
(2) UL listed wire nuts (optional)
(2) UL listed G13 lampholders (optional)
(1) Fixture modication label
toggled is an company
En
If you have any problems
or questions, contact our
tech support team at
1-844-864-4533 Monday-
Friday, 8-5pm EST or email
[e-mail]
Si tiene algún problema o
desea realizar una pregunta,
comuníquese con nuestro
equipo de asistencia técnica
llamando al teléfono
1-844-864-4533, de lunes a
viernes, de 8 a. m. a 5 p. m.
(hora estándar del este), o
envíenos un correo electrónico
a [e-mail]
Si vous avez des problèmes
ou des questions, veuillez
communiquer avec notre équipe
de soutien technique par
téléphone au 1 844 864 4533,
du lundi au vendredi, de 8 h à
17 h (HNE), ou par courriel au
[e-mail]
• WARNING – Risk of re or electric shock. LED Retrot Kit installation requires
knowledge of luminaires electrical systems. If not qualied, do not attempt
installation. Contact a qualied electrician.
• WARNING – Risk of re or electric shock. Install this kit only in the luminaires
that have the construction features and dimensions shown in the photographs
and/or drawings.
• Do not make or alter any open holes in an enclosure of wiring or electrical
components during kit installation.
• WARNING – To prevent wire abrasion, do not expose wiring to edges of
sheet metal or other sharp objects.
• WARNING – To avoid potential re or shock hazard, do not use this retrot kit
in luminaires employing shunted bi-pin lampholders.
• WARNING – This xture must be grounded and installed in accordance with
local and national electrical codes, by a person familiar with the construction
and operation of the product and the hazards involved.
• Note: Shunted lampholders are found only in uorescent luminaires with
Instant-Start ballasts. Instant-Start ballasts can be identied by the words
“Instant Start” or “I.S.” marked on the ballast. This designation may be in the
form of a statement pertaining to the ballast itself or may be combined with
the marking for the lamps with which the ballast is intended to be used, for
example F40T12/IS. For more information, contact toggled.
• Installers should not disconnect existing wires from lampholder terminals to
make new connections at lampholder terminals. Instead installers should cut
existing lampholder leads away from the lampholder and make new electrical
connections to lampholder lead wires by employing applicable connectors.
• This device is not intended for use with emergency exits.
• This device is not intended for use with dimmers.
toggled.com/installation
FIXTURE RETROFIT INSTRUCTIONS
WARNING - To avoid shock or re hazard, turn off power to the xture at the
appropriate breaker or fuse panel.
STEP 1: Verify the voltage rating of the lamp (120-277VAC) matches the voltage of the
xture circuit.
STEP 2: Remove old uorescent lamps and remove the ballast cover.
STEP 3: Cut all wires attached to the ballast(s) as close to the ballast(s) as possible. Leave
the ballast(s) in place.
Note: toggled lamps are powered from a single-end (designated with the product label or
markings) and require the use of non-shunted lampholders.
If the lampholders are shunted, replace them with non-shunted lampholders. See
“Shunted Lampholder Replacement” below. Non-shunted lampholders are an optional
accessory. If the lamp was not supplied with replacement lampholders they may be
purchased separately.
STEP 4: Connect one wire from each lampholder at one end of the xture to line (black)
and separately connect the other wire to neutral (white). At the opposite end of the xture,
cut all wires from the lampholders.
Note: Ensure the xture is and remains grounded after the retrot process.
STEP 5: Reinstall any removed wiring covers and ballast covers.
STEP 6: Afx the included xture-modication label to the newly retrotted xture. To indi-
cate which end is powered, place the label on the ballast cover nearest the powered end.
STEP 7: Install the new toggled lamp(s). Be sure to install the lamp in the proper
orientation (the end with the product labels/markings should be connected
to the AC wired lampholders).