Instructions / Assembly

Tube Installation Instructions
E416-##310, E312-XX310, E208-XX310, E425-XX320,
E425-G#320, E213-XX320, E213-G#320
Included:
Installation Instructions
LED tube(s)
Fixture label(s)
Important Information - Read before beginning installation:
Warning - Risk of re or electric shock. LED Retrot Kit installation
requires knowledge of luminaires electrical systems. If not qualied,
do not attempt installation. Contact a qualied a electrician.
Warning - Risk of re or electric shock. Install this kit only in the
luminaires that have the construction features and dimensions shown
in the photographs and/or drawings and where the input rating of the
retrot kit does not exceed the input rating of the luminaire.
Warning - To prevent wire abrasion, do not expose wiring to edges of
sheet metal or other sharp objects.
Warning - This xture must be grounded and installed in accordance
with all national and local electrical codes, by a person familiar with
the construction and operation of the product and the hazards
involved.
Warning - To avoid potential re or shock hazard, do not use this
retrot kit in luminaires employing shunted bi-pin lampholders.
Installers should not disconnect existing wires from lampholder
terminals to make new connections at lampholder teminals. Instead,
installers should cut existing lampholder leads away from the
lampholder and make new electrical connections to lampholder lead
wires by employing applicable connectors.
Do not make or alter any open holes in an enclosure of wiring or
electrical components during kit installation.
This device is not intended for use with emergency exits.
This retrot process does not change the environmental rating of the
xture being retrotted. For damp location placements, the xture
needs to be rated as such.
This device is intended for indoor use or weather protected xtures
only. Do not use where directly exposed to water or water spray.
The retrot kit is accepted as a component of a luminaire where the
suitability of the combination shall be determined by authorities
having jurisdiction. Product must be installed by a qualied electrician
in accordance with the applicable and appropriate electrical codes.
The installation guide does not supersede local or national regulations
for electrical installation.
This device is not intended for use with dimmers.
FCC Notice
This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt
RSS Standards. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in an installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modications not expressly approved by Toggled could avoid the user’s authority
to operate the equipment. This equipment complies with FCC radiation exposure limits set
forth for an uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body.
1.844.864.4533 [e-mail] See toggled.com/warranty for details.
11-01768-AG 2021.02.08
Troubleshooting
Symptom Potential Causes Remedy
LED tube installed
backwards
Ensure the lamp is installed
with the “AC Input” marking
on the powered end of the
xture
No light from LED tube(s)
when powered on.
Fixture wired improperly
or loose connections exist
Installation
1. Turnoffpowertotheuorescent
 xture(s)atthecircuitbreaker.
Wires should be cut as close to the ballast as possible as you
may need to reuse them later.
8. Turnpowerbackonatthecircuit
 breaker.
For additional help or support, please contact Toggled support: Phone
1.844.864.4533. Email [e-mail]
IMPORTANT - Installation of Toggled LED tubes requires
modication of the wiring within the existing uorescent xture.
Please read the entire installation instructions before beginning
your installation.
Please examine all parts that are not intended to be replaced by
the retrot kit for damage and replace any damaged parts prior to
installation of the retrot kit.
2. Removeexistinguorescenttubes
and ballast cover.
3. Cutallwiresattachedtotheballast(s).
BALLAST
4. Connect lampholders to the AC
 supply(120-277VAC).
Toggled Tubes are powered from only one end and require
the use of non-shunted lampholders.
• The powered end is labeled with “AC Input” on the tube.
• The opposite end is for mechanical support only and is
not electrically connected.
• If lampholders are shunted, they must be replaced with
non-shunted lampholders.
5. Reinstall any removed ballast covers
or wiring covers.
6. Applythexturemodicationlabel
 tothepoweredendofthexture.
7. InstallthenewToggledTube(s).
Line (Hot)
Neutral
Powered End
What are shunted lampholders?
Shunted lampholders have contacts that are connected
together internally (shorted). As a result, line and neutral cannot
be supplied separately to the lamp with a shunted lampholder.
Note: Shunted lampholders are found only in uorescent
luminaries with Instant-Start ballasts.
Instant-Start ballasts can be identied by the words “Instant
Start” or “I.S.” marked on the ballast. This designation may be
in the form of a statement pertaining to the ballast itself or may
be combined with the marking for the lamps with which the
ballast is intended to be used, for example F40T12/IS.
For more information contact Toggled.
Shunted Lampholder Replacement
A. Remove brackets or covers holding the shunted
lampholders.
B. Remove the existing shunted lampholders.
C. Install new pre-wired lampholders optionally
included with this retrot kit.
D. Route wires from new lampholders to incoming power
source.
E. Resume installation at Step 4.
Circuit breaker trips when
power is turned on
All other issues
Damaged LED tube
• Verify wiring matches
instructions
• Check wire-nuts for loose
connections
• Verify voltage at
lampholder(s), verify
120-277VAC is supplied
to pins on powered on off
lamp
Contact Toggled
(1.844.864.4533,
[e-mail])
Shunted lampholders
installed
Fixture wired improperly
Replace lampholders with
non-shunted lampholders
• Verify wiring matches
instructions
• Check wire-nuts for loose
connections
• Verify voltage at
lampholder(s), verify 120-
277VAC is supplied to pins
on powered on off lamp
Unknown Contact Toggled
(1.844.864.4533,
[e-mail])
Watch installation video
www.toggled.com/installation
Installation video: www.toggled.com/installation
Optional Accessories:
Pre-wired lampholder (1 per tube)
Non-shunted lampholder (1 per tube)
Wire nuts (2 per tube)
Neutral
Line (Hot)
Fluorescent Tube
BALLAST
Fluorescent Tube
Fluorescent Tube
Fluorescent Tube
Neutral
Line (Hot)
Neutral
Line (Hot)
The powered end (“AC Input”) of the lamp must
face the wired end of the xture.
For E416-##310, E312-XX310, E208-XX310:
The maximum number of tubes installed in a single xture is 4.
For E425-XX320, E425-G#320:
Maintain minimum spacing of 75mm between lamps (center-to-center).
For E213-XX320, E213-G#320:
Maintain minimum spacing of 75mm between lamps (center-to-center).
AC INPUT
09-01801-AB
This luminaire has been modified to operate LED lamps.
Do not attempt to install or operate fluorescent lamps in this luminaire.
Replace using only Toggled direct-wire LED lamps.
Line (120-277VAC)
Neutral
1.844.864.4533
www.toggled.com
Minimum xture dimensions (LxWxH):
E425-XX320, E425-G#320:
E213-XX320, E213-G#320:
E416-##310:
E312-XX310:
E208-XX310:
1220mm x 540mm x 75mm
620mm x 540mm x 75mm
1220mm x 550mm x 75mm
920mm x 560mm x 75mm
625mm x 560mm x 75mm