User Manual
Table Of Contents
- TTM-200ｼﾘｰｽﾞﾕｰｻﾞｰｽﾞﾏﾆｭｱﾙ 英語 48-7009-Ｄ.pdfから挿入したしおり
- TOP
- Contents
- 2. Installation
- 3. Wiring
- 4. Basic operation
- 5. Operating the equipment
- 5.1 Precautions on operating the equipment
- 5.2 Operating monitor display
- 5.3 How to set run settings
- 5.4 How to set each function and description of function
- 5.5 Explanation of the program run function
- 5.5.1 Operation flow of the program run
- 5.5.2 SET 21 program function setting
- 5.5.3 SET 21 program function setting screen
- 5.5.4 SET 22 program setting
- 5.5.5 SET 22 program setting screen
- 5.5.6 Explanation of the screen display and operation of a program run
- 5.5.7 Complementary explanation of the program run
- 5.6 Explanation of the bank automatic switching function
- 6. Explanation on parameters
- 6.1 Input 1 type setting
- 6.2 Remote SV input type setting
- 6.3 Function key function setting
- 6.4 Control function setting
- 6.5 Output (from OUT 1 to OUT 7) type setting
- 6.6 Current transformer (CT) setting
- 6.7 DI setting
- 6.8 Timer function setting
- 6.9 Communication function setting
- 6.10 Initial setting
- 6.11 Priority screen setting
- 6.12 Bank function setting
- 6.13 PROGRAM FUNCTION SETTING
- 6.14 PROGRAM SETTING
- 6.15 BANK AUTOMATIC SWITCHING FUNCTION SETTING
- 7. Appendix
- 7.1 Product specifications
- 7.2 Accessories
- 7.3 Error (abnormality) display
- 7.4 Troubleshooting
- 7.5 Setting list
- 7.5.1 Run mode
- 7.5.2 Input 1 setting mode (SET 01)
- 7.5.3 Input 2 setting mode (SET 02)
- 7.5.4 Key function setting mode (SET 03)
- 7.5.5 Control setting mode (SET 04) (1/4)
- 7.5.6 OUT 1 and 2 setting modes (SET 05 and 06) (1/3)
- 7.5.7 OUT 3 to 7 setting modes (SET 07, 08, 09, 10 and 11) (1/2)
- 7.5.8 CT setting mode (SET 12)
- 7.5.9 DI setting mode (SET 13)
- 7.5.10 Timer 1 to 3 setting modes (SET 14, 15 and 16)
- 7.5.11 Communication setting mode (SET 17)
- 7.5.12 Initial setting mode (SET 18)
- 7.5.13 Priority screen setting mode (SET 19)
- 7.5.14 Bank setting mode (SET 20)
- 7.5.15 Program function setting mode (SET 21)
- 7.5.16 Program setting mode (SET 22)
- 7.5.17 Bank automatic switching function setting mode (SET 23)
48-7009-E 5-73
5.6.2 SET 23 bank automatic switching function setting mode setting screen
■ The bank automatic switching function setting screen is shown below:
SET23
ZBNK
BAS
0
PM7
1200
ASC
0
PM1
1200
25
25
Returns to SET23 ZBNK
SET01
INP1
BAF
0
Hold MODE key pressed for 2 seconds
Hold MODE key pressed for 2 seconds
No.
Setting range
0
Bank automatic switching run OFF (initial value)
1
Bank automatic switching run ON
* Condition for non-display
• When SET 04 bANKH 0
PV value (present value)
SV value (setting value)
Input 1 setting screen
Press the key or key several times.
Setting the bank automatic
switching function setting mode
Press MODE key.
Bank automatic switching
function selection
•
•
•
Press MODE key.
Bank automatic switching
source setting
No.
Setting range
0
SV value (initial value)
1
Ramp SV value
2
PV value
* Condition for non-display
• When bAF = 0 (OFF)
• When SET 04 bANKH 0
Zone threshold 1 setting
Press MODE key.
Setting range: PM* = SLL to SLH (initial value: 1200)
(*=1 to 7)
Press MODE key.
* Zone threshold 1-to-7 setting
* Condition for non-display
- When bAF = 0 (OFF)
- When SET 04 bANKH 0
Displayed PM* varies depending on
the bANKH value.
Zone threshold 7 setting
Zone threshold switching
sensitivity range setting
Press MODE key.
Press MODE key.
During temperature input (initial value = 2)
Setting range: 0 to 999 or (0.0 to 999.9) C
During analog input
Setting range: 0 to 9999 digit
* Condition for non-display
• When bAF = 0 (OFF) and BAS = 0
• When BAS = 1 and SET 02 LR = 0
• When SET 04 bANKH 0