User Manual
Table Of Contents
- TTM-200ｼﾘｰｽﾞﾕｰｻﾞｰｽﾞﾏﾆｭｱﾙ 英語 48-7009-Ｄ.pdfから挿入したしおり
- TOP
- Contents
- 2. Installation
- 3. Wiring
- 4. Basic operation
- 5. Operating the equipment
- 5.1 Precautions on operating the equipment
- 5.2 Operating monitor display
- 5.3 How to set run settings
- 5.4 How to set each function and description of function
- 5.5 Explanation of the program run function
- 5.5.1 Operation flow of the program run
- 5.5.2 SET 21 program function setting
- 5.5.3 SET 21 program function setting screen
- 5.5.4 SET 22 program setting
- 5.5.5 SET 22 program setting screen
- 5.5.6 Explanation of the screen display and operation of a program run
- 5.5.7 Complementary explanation of the program run
- 5.6 Explanation of the bank automatic switching function
- 6. Explanation on parameters
- 6.1 Input 1 type setting
- 6.2 Remote SV input type setting
- 6.3 Function key function setting
- 6.4 Control function setting
- 6.5 Output (from OUT 1 to OUT 7) type setting
- 6.6 Current transformer (CT) setting
- 6.7 DI setting
- 6.8 Timer function setting
- 6.9 Communication function setting
- 6.10 Initial setting
- 6.11 Priority screen setting
- 6.12 Bank function setting
- 6.13 PROGRAM FUNCTION SETTING
- 6.14 PROGRAM SETTING
- 6.15 BANK AUTOMATIC SWITCHING FUNCTION SETTING
- 7. Appendix
- 7.1 Product specifications
- 7.2 Accessories
- 7.3 Error (abnormality) display
- 7.4 Troubleshooting
- 7.5 Setting list
- 7.5.1 Run mode
- 7.5.2 Input 1 setting mode (SET 01)
- 7.5.3 Input 2 setting mode (SET 02)
- 7.5.4 Key function setting mode (SET 03)
- 7.5.5 Control setting mode (SET 04) (1/4)
- 7.5.6 OUT 1 and 2 setting modes (SET 05 and 06) (1/3)
- 7.5.7 OUT 3 to 7 setting modes (SET 07, 08, 09, 10 and 11) (1/2)
- 7.5.8 CT setting mode (SET 12)
- 7.5.9 DI setting mode (SET 13)
- 7.5.10 Timer 1 to 3 setting modes (SET 14, 15 and 16)
- 7.5.11 Communication setting mode (SET 17)
- 7.5.12 Initial setting mode (SET 18)
- 7.5.13 Priority screen setting mode (SET 19)
- 7.5.14 Bank setting mode (SET 20)
- 7.5.15 Program function setting mode (SET 21)
- 7.5.16 Program setting mode (SET 22)
- 7.5.17 Bank automatic switching function setting mode (SET 23)
48-7009-E 6-3
Input 1 connection table
Model
TTM-200 Series
Model No.
204
205
209
207
Connection
Wiring
Terminal No.
Terminal No.
Terminal No.
TC
12
11
24
23
18
17
RTD
A
B
b
12
11
10
24
23
22
18
17
16
I/V
10
11
22
23
16
17
Note Switchover of the input types may result in change of each setting value due to limits being applied, such as SLH, SLL,
tRH and tRL.
■ Display scaling upper limit/lower limit setting
SEt01
INP1
Setting content
Initial value
2
FSH1
Voltage/current input only
FSL 1 to 29999 (digit)
10000
3
FSL1
Voltage/current input only
-19999 to FSH 1 (digit)
-10000
Display scaling upper limit/lower limit are set for the input 1.
This setting is possible only when the input 1 is set for voltage/current input.
Setting example: Where the input type is the 4 - 20 mA setting and the display range is 0.0 digit for 4 mA and 100.0 digits
for 20 mA.
Set as INP 1: 20, FSH 1: 100.0, FSL 1: 0.0 and dP 1: 0.0.
* For this setting, the display range is - 12.0 to 112.0.
For -12.0 or smaller, the display is “underscale display.”
For 112.0 or larger, the display is “overscale display.”
ＰＶ
Input 1
4mA
20mA
１００．０％（ＦＳＨ１）
０．０％（ＦＳＬ１）
Note
(1) Display resolution is 20,000 or less.
Take care it when the range from FSL 1 to FSH 1 is set larger than 20,000.
Setting example: Fluctuation or missing value of PV may be caused when the input 1 is set to the input type of 4 - 20 mA,
FSL 1 to -19999 digits and FSH 1 to 29999 digits.
(2) Take care that setting values for FSH 1 and FSL 1 can be the same.