User Manual
Table Of Contents
- TTM-200ｼﾘｰｽﾞﾕｰｻﾞｰｽﾞﾏﾆｭｱﾙ 英語 48-7009-Ｄ.pdfから挿入したしおり
- TOP
- Contents
- 2. Installation
- 3. Wiring
- 4. Basic operation
- 5. Operating the equipment
- 5.1 Precautions on operating the equipment
- 5.2 Operating monitor display
- 5.3 How to set run settings
- 5.4 How to set each function and description of function
- 5.5 Explanation of the program run function
- 5.5.1 Operation flow of the program run
- 5.5.2 SET 21 program function setting
- 5.5.3 SET 21 program function setting screen
- 5.5.4 SET 22 program setting
- 5.5.5 SET 22 program setting screen
- 5.5.6 Explanation of the screen display and operation of a program run
- 5.5.7 Complementary explanation of the program run
- 5.6 Explanation of the bank automatic switching function
- 6. Explanation on parameters
- 6.1 Input 1 type setting
- 6.2 Remote SV input type setting
- 6.3 Function key function setting
- 6.4 Control function setting
- 6.5 Output (from OUT 1 to OUT 7) type setting
- 6.6 Current transformer (CT) setting
- 6.7 DI setting
- 6.8 Timer function setting
- 6.9 Communication function setting
- 6.10 Initial setting
- 6.11 Priority screen setting
- 6.12 Bank function setting
- 6.13 PROGRAM FUNCTION SETTING
- 6.14 PROGRAM SETTING
- 6.15 BANK AUTOMATIC SWITCHING FUNCTION SETTING
- 7. Appendix
- 7.1 Product specifications
- 7.2 Accessories
- 7.3 Error (abnormality) display
- 7.4 Troubleshooting
- 7.5 Setting list
- 7.5.1 Run mode
- 7.5.2 Input 1 setting mode (SET 01)
- 7.5.3 Input 2 setting mode (SET 02)
- 7.5.4 Key function setting mode (SET 03)
- 7.5.5 Control setting mode (SET 04) (1/4)
- 7.5.6 OUT 1 and 2 setting modes (SET 05 and 06) (1/3)
- 7.5.7 OUT 3 to 7 setting modes (SET 07, 08, 09, 10 and 11) (1/2)
- 7.5.8 CT setting mode (SET 12)
- 7.5.9 DI setting mode (SET 13)
- 7.5.10 Timer 1 to 3 setting modes (SET 14, 15 and 16)
- 7.5.11 Communication setting mode (SET 17)
- 7.5.12 Initial setting mode (SET 18)
- 7.5.13 Priority screen setting mode (SET 19)
- 7.5.14 Bank setting mode (SET 20)
- 7.5.15 Program function setting mode (SET 21)
- 7.5.16 Program setting mode (SET 22)
- 7.5.17 Bank automatic switching function setting mode (SET 23)
48-7009-E 6-60
6: Start and Stop of the timer operation, which is set in “function setting - DI 1 to 4 start” for timers 1 to 3 (see SET 14 to 16 on page
6-59, are switched over.
Stopping the timer during operation results to midway termination (state of control stop or event output OFF).
Note Setting with DI supersedes the setting change of “communication” or “FUNC key.”
Note Setting the function setting to the bank switchover may cause high-speed switchovers of banks when setting the DI function
setting to a bank.
To solve this phenomenon, delete DI function setting DIF from the bank setting, set DIF to the bank switchover setting, and
put the DIF into the bank.
Note Choose the open collector output when change DI by the event output.
7: CONSTANT OPERATION / PRGRAM MODE SWITCHING 3
Switching between the Constant Operation and the Program Mode will be made
8: STEP FORWARD 3
steps can be forwarded during the program mode.
NOTE: This function is effective only when the Program Mode is being selected.
9: PAUSE 3
By pressing the FUNC-key, the Program Operation can be stopped temporarily.
Switching between Pause – In Operation will be made.
NOTE: This function is effective only when the Program Mode is being selected.
A: Inter-Lock 3
When the "DI = Non-Active", the Control Mode can be stopped forcibly.
Its priority is the highest over all the Control Mode Condition.
The setting of Control Mode Condition can be switched with （SEt04 Md）（SEt03 FU*）（SEt13 DIF）.
NOTE: During Constant Operation Mode
When dIF=A, at the same time, the function-key function is set to FU1 – 5 = 2, to re-start the operation after DI=Active,
press function key.
NOTE: During the Program Mode
With DI=Non-Active, it will forcibly go back to “Pre-Operation Condition”. Re-start the operation after DI=Active.