User Manual
Table Of Contents
- TTM-200ｼﾘｰｽﾞﾕｰｻﾞｰｽﾞﾏﾆｭｱﾙ 英語 48-7009-Ｄ.pdfから挿入したしおり
- TOP
- Contents
- 2. Installation
- 3. Wiring
- 4. Basic operation
- 5. Operating the equipment
- 5.1 Precautions on operating the equipment
- 5.2 Operating monitor display
- 5.3 How to set run settings
- 5.4 How to set each function and description of function
- 5.5 Explanation of the program run function
- 5.5.1 Operation flow of the program run
- 5.5.2 SET 21 program function setting
- 5.5.3 SET 21 program function setting screen
- 5.5.4 SET 22 program setting
- 5.5.5 SET 22 program setting screen
- 5.5.6 Explanation of the screen display and operation of a program run
- 5.5.7 Complementary explanation of the program run
- 5.6 Explanation of the bank automatic switching function
- 6. Explanation on parameters
- 6.1 Input 1 type setting
- 6.2 Remote SV input type setting
- 6.3 Function key function setting
- 6.4 Control function setting
- 6.5 Output (from OUT 1 to OUT 7) type setting
- 6.6 Current transformer (CT) setting
- 6.7 DI setting
- 6.8 Timer function setting
- 6.9 Communication function setting
- 6.10 Initial setting
- 6.11 Priority screen setting
- 6.12 Bank function setting
- 6.13 PROGRAM FUNCTION SETTING
- 6.14 PROGRAM SETTING
- 6.15 BANK AUTOMATIC SWITCHING FUNCTION SETTING
- 7. Appendix
- 7.1 Product specifications
- 7.2 Accessories
- 7.3 Error (abnormality) display
- 7.4 Troubleshooting
- 7.5 Setting list
- 7.5.1 Run mode
- 7.5.2 Input 1 setting mode (SET 01)
- 7.5.3 Input 2 setting mode (SET 02)
- 7.5.4 Key function setting mode (SET 03)
- 7.5.5 Control setting mode (SET 04) (1/4)
- 7.5.6 OUT 1 and 2 setting modes (SET 05 and 06) (1/3)
- 7.5.7 OUT 3 to 7 setting modes (SET 07, 08, 09, 10 and 11) (1/2)
- 7.5.8 CT setting mode (SET 12)
- 7.5.9 DI setting mode (SET 13)
- 7.5.10 Timer 1 to 3 setting modes (SET 14, 15 and 16)
- 7.5.11 Communication setting mode (SET 17)
- 7.5.12 Initial setting mode (SET 18)
- 7.5.13 Priority screen setting mode (SET 19)
- 7.5.14 Bank setting mode (SET 20)
- 7.5.15 Program function setting mode (SET 21)
- 7.5.16 Program setting mode (SET 22)
- 7.5.17 Bank automatic switching function setting mode (SET 23)
48-7009-E 6-76
■Wait Range Setting
ＳＥｔ２１
ＰＧＦ
Setting Contents
Initial
Value
5
ＷＡＩｔ
Wait Range Setting 3
2
During Temperature Input
Soak Time 1
0～999（0．0～999．9）（℃）
Soak Time 2
0～999（0．0～999．9）（℃）
※During H/MP(Soak Time 2)、the behavior will
be identical to that of (Soak Time 1) with Setting=0
During Analog Input
Soak Time 1
0～9999（digit）
Soak Time 2
0～9999（digit）
※During H/MP(Soak Time 2)、the behavior will
be identical to that of (Soak Time 1) with Setting=0
＊5 WAIT RANGE SETTING (WAIt)
Time Unit Setting (H/MP) sets the condition of countdown (Range against PV Value) during the setting of
(Soak Time 1) (Soak Time 2).
Please refer to Time Unit Setting (H/MP) for the explanation of its action.
Setting Range
(During Temp. Input)
Soak Time 1: 0 to 999 (0.0 to 999.9)℃
Soak Time 2: 0 to 999 (0.1 to 999.9)℃
(During Analog Input)
Soak Time 1: 0 to 9999 (digit)
Soak Time 2: 0 to 9999 (digit)
NOTE: RE: Behavior during WAIT Range Setting (Setting Value = 0)
Even if the H/MP (Soak Time 2) is being set, when the Setting Value = 0, the behavior would be the same as that of (Soak
Time 1).
NOTE: Regarding the AT (Auto-Tuning) behavior during the program in operation.
The AT can be done while the program is in operation. The SV Value which operates the AT is the SV* (Step SV) Value that is set in
each steps. Also, this condition applies also during RMP in operation with set RMP movement.