User Manual
Table Of Contents
- TTM-200ｼﾘｰｽﾞﾕｰｻﾞｰｽﾞﾏﾆｭｱﾙ 英語 48-7009-Ｄ.pdfから挿入したしおり
- TOP
- Contents
- 2. Installation
- 3. Wiring
- 4. Basic operation
- 5. Operating the equipment
- 5.1 Precautions on operating the equipment
- 5.2 Operating monitor display
- 5.3 How to set run settings
- 5.4 How to set each function and description of function
- 5.5 Explanation of the program run function
- 5.5.1 Operation flow of the program run
- 5.5.2 SET 21 program function setting
- 5.5.3 SET 21 program function setting screen
- 5.5.4 SET 22 program setting
- 5.5.5 SET 22 program setting screen
- 5.5.6 Explanation of the screen display and operation of a program run
- 5.5.7 Complementary explanation of the program run
- 5.6 Explanation of the bank automatic switching function
- 6. Explanation on parameters
- 6.1 Input 1 type setting
- 6.2 Remote SV input type setting
- 6.3 Function key function setting
- 6.4 Control function setting
- 6.5 Output (from OUT 1 to OUT 7) type setting
- 6.6 Current transformer (CT) setting
- 6.7 DI setting
- 6.8 Timer function setting
- 6.9 Communication function setting
- 6.10 Initial setting
- 6.11 Priority screen setting
- 6.12 Bank function setting
- 6.13 PROGRAM FUNCTION SETTING
- 6.14 PROGRAM SETTING
- 6.15 BANK AUTOMATIC SWITCHING FUNCTION SETTING
- 7. Appendix
- 7.1 Product specifications
- 7.2 Accessories
- 7.3 Error (abnormality) display
- 7.4 Troubleshooting
- 7.5 Setting list
- 7.5.1 Run mode
- 7.5.2 Input 1 setting mode (SET 01)
- 7.5.3 Input 2 setting mode (SET 02)
- 7.5.4 Key function setting mode (SET 03)
- 7.5.5 Control setting mode (SET 04) (1/4)
- 7.5.6 OUT 1 and 2 setting modes (SET 05 and 06) (1/3)
- 7.5.7 OUT 3 to 7 setting modes (SET 07, 08, 09, 10 and 11) (1/2)
- 7.5.8 CT setting mode (SET 12)
- 7.5.9 DI setting mode (SET 13)
- 7.5.10 Timer 1 to 3 setting modes (SET 14, 15 and 16)
- 7.5.11 Communication setting mode (SET 17)
- 7.5.12 Initial setting mode (SET 18)
- 7.5.13 Priority screen setting mode (SET 19)
- 7.5.14 Bank setting mode (SET 20)
- 7.5.15 Program function setting mode (SET 21)
- 7.5.16 Program setting mode (SET 22)
- 7.5.17 Bank automatic switching function setting mode (SET 23)
48-7009-E 6-77
6.14 PROGRAM SETTING
■Setting No. of Steps to be Used / Step SV＊ Setting / Step Time＊ Setting
ＳＥｔ２２
ＰＲＯＧ
SETTING CONTENTS
INITIAL
VALUE
1
ＳｔＥＰＮ
Setting of no. of steps used 3
8
Setting Value Range n=1～8
2
Ｓｔ＊ｂＫ
Step＊ Designated Bank Setting 3
0
Setting Value Range St*BK=0～7
*=1～(StEPN Setting Value)
3
ＳＶ＊
Step SV＊ Setting 3
0
Setting Value Range SV*=SLL～SLH
*=1～(StEPN Setting Value)
※When the SLL and SLH is set at the Bank, the
value of the SLL,SLH will be set on each bank.
4
ｔＩＭ＊
Step Time＊ Setting 3
00:00
Setting Value Range TIM*=00:00～99:59
*=1～(StEPN Setting Value)
Sets the Program Step Data of the Program Setting Mode.
＊1 No. of Steps Used Setting (StEPN)
This is to set the “Max. No. of Steps” which is used in the programmed operation.
＊2 Step＊ Designated Bank Setting (St＊bK)
This is to set the “Bank Nos.” which the system refers in every step.
＊3 Step SV＊ Setting (SV＊)
This is to set the target value (temperature or analog value) of the control in every steps.
＊4 Step Time＊ Setting (tIM＊)
This is to set the Step Duration Time of every steps.
The next page shows the behavior diagram of the “No. of Steps Used Setting / Step SV＊ Setting / Step Time＊ Setting”.