User Manual
Table Of Contents
- TTM-200ｼﾘｰｽﾞﾕｰｻﾞｰｽﾞﾏﾆｭｱﾙ 英語 48-7009-Ｄ.pdfから挿入したしおり
- TOP
- Contents
- 2. Installation
- 3. Wiring
- 4. Basic operation
- 5. Operating the equipment
- 5.1 Precautions on operating the equipment
- 5.2 Operating monitor display
- 5.3 How to set run settings
- 5.4 How to set each function and description of function
- 5.5 Explanation of the program run function
- 5.5.1 Operation flow of the program run
- 5.5.2 SET 21 program function setting
- 5.5.3 SET 21 program function setting screen
- 5.5.4 SET 22 program setting
- 5.5.5 SET 22 program setting screen
- 5.5.6 Explanation of the screen display and operation of a program run
- 5.5.7 Complementary explanation of the program run
- 5.6 Explanation of the bank automatic switching function
- 6. Explanation on parameters
- 6.1 Input 1 type setting
- 6.2 Remote SV input type setting
- 6.3 Function key function setting
- 6.4 Control function setting
- 6.5 Output (from OUT 1 to OUT 7) type setting
- 6.6 Current transformer (CT) setting
- 6.7 DI setting
- 6.8 Timer function setting
- 6.9 Communication function setting
- 6.10 Initial setting
- 6.11 Priority screen setting
- 6.12 Bank function setting
- 6.13 PROGRAM FUNCTION SETTING
- 6.14 PROGRAM SETTING
- 6.15 BANK AUTOMATIC SWITCHING FUNCTION SETTING
- 7. Appendix
- 7.1 Product specifications
- 7.2 Accessories
- 7.3 Error (abnormality) display
- 7.4 Troubleshooting
- 7.5 Setting list
- 7.5.1 Run mode
- 7.5.2 Input 1 setting mode (SET 01)
- 7.5.3 Input 2 setting mode (SET 02)
- 7.5.4 Key function setting mode (SET 03)
- 7.5.5 Control setting mode (SET 04) (1/4)
- 7.5.6 OUT 1 and 2 setting modes (SET 05 and 06) (1/3)
- 7.5.7 OUT 3 to 7 setting modes (SET 07, 08, 09, 10 and 11) (1/2)
- 7.5.8 CT setting mode (SET 12)
- 7.5.9 DI setting mode (SET 13)
- 7.5.10 Timer 1 to 3 setting modes (SET 14, 15 and 16)
- 7.5.11 Communication setting mode (SET 17)
- 7.5.12 Initial setting mode (SET 18)
- 7.5.13 Priority screen setting mode (SET 19)
- 7.5.14 Bank setting mode (SET 20)
- 7.5.15 Program function setting mode (SET 21)
- 7.5.16 Program setting mode (SET 22)
- 7.5.17 Bank automatic switching function setting mode (SET 23)
48-7009-E 6-80
6.15 BANK AUTOMATIC SWITCHING FUNCTION SETTING
■Bank Automatic Switching Function Selection
ＳＥｔ２３
ＺｂＮＫ
Setting Contents
Initial
Value
1
ｂＡＦ
Bank Automatic Switching Function Selection 3
0
0
Bank Auto-Switching Operation OFF
1
Bank Auto-Switching Operation ON
※In case the “Bank Auto-Switching Operation
ON” is set;
・The Bank Switching Setting with the FUNC
Key will be invalid.
・The Bank Switching Setting by DI will be
invalid.
▲▼ key operation will not be possible either.
※When SET04 bANKH=0, the setting will be
invalid.
There will be no indication either.
※１ Bank Automatic Switching Function Selection (bAF)
This is to set the Bank Automatic Switching ON/OFF. When ON, the bank will be switched
automatically with the selected input by the Bank Automatic Switching Source Setting (bAS).
Setting Range：When 0: Bank Automatic Switching Operation OFF
When 1: Bank Automatic Switching Operation ON
■Behavior Diagram when Bank Automatic Switching is ON
BANK1
ＲＭＰ
10
Ｐ１
4.0
・
・
・
Ｉ
20
Ｄ
5
BANK2
ＲＭＰ
10
・
・
・
BANK3
ＲＭＰ
10
・
・
・
BANK4
ＲＭＰ
10
・
・
・
BANK5
ＲＭＰ
5
・
・
・
BANK6
ＲＭＰ
5
・
・
・
BANK7
ＲＭＰ
10
・
・
・
BANK0
ＲＭＰ
Ｐ１
3.0
MAX. 16 parameter
・
・
・
Ｉ
0
Ｄ
0
SV
Ｐ１
2.0
Ｉ
10
Ｄ
2
Ｐ１
4.0
Ｉ
20
Ｄ
5
Ｐ１
4.0
Ｉ
20
Ｄ
5
Ｐ１
4.0
Ｉ
20
Ｄ
5
Ｐ１
4.0
Ｉ
20
Ｄ
5
Ｐ１
2.0
Ｉ
10
Ｄ
2
SET20
setting
Refer
BANK0
BANK1
BANK2
BANK3
BANK4
BANK5
BANK6
BANK7
ＰＭ１
ＰＭ2
ＰＭ3
ＰＭ4
ＰＭ5
ＰＭ6
ＰＭ7
SLH
SLL
SLL≦
＜PM1
SV
value
PM1≦
＜PM2
PM2≦
＜PM3
PM3≦
＜PM4
PM4≦
＜PM5
PM5≦
＜PM6
PM6≦
＜PM7
PM7≦
＜SLH
Bank Automatic Switching.
Switch the bank in accordance with
the source(SV)..
MAX. 8BANK
①
②
③
④
⑤
④
①
③
① 10℃
PM*
setting
PM1
PM2
PM3
PM4
PM5
PM6
PM7
SLL
SLH
20℃
0℃
40℃
60℃
90℃
120℃
140℃
160℃
200℃
② 35℃
Bank 0
Bank 1
Bank 2
Bank 3
Bank 4
Bank 5
Bank 6
Bank 7
③ 70℃
④ 100℃
⑤ 150℃
Auto-Switching
sorce
Bank No.
8BANK（All Threshold＊Setting <PM1 to PM7)>）
Bank 7
Zone
Threshold
Setting
NOTE: When the Bank Automatic Switching Function is (SET23 bAF = 1), please note the following points in
case the parameters “SV, SLL, SLH” is set at SET 20 (Bank);
・The value of the “SV, SLL, SLH” set at the Bank will be invalid.
・The Bank registration of “SV, SLL, SLH” will be erased and will go back to the default value.
If (SET 23 bAF = 0) again, the bank registration of “SV, SLL, SLH” are erased, so there is a need to reset.