User Manual
Table Of Contents
- TTM-200ｼﾘｰｽﾞﾕｰｻﾞｰｽﾞﾏﾆｭｱﾙ 英語 48-7009-Ｄ.pdfから挿入したしおり
- TOP
- Contents
- 2. Installation
- 3. Wiring
- 4. Basic operation
- 5. Operating the equipment
- 5.1 Precautions on operating the equipment
- 5.2 Operating monitor display
- 5.3 How to set run settings
- 5.4 How to set each function and description of function
- 5.5 Explanation of the program run function
- 5.5.1 Operation flow of the program run
- 5.5.2 SET 21 program function setting
- 5.5.3 SET 21 program function setting screen
- 5.5.4 SET 22 program setting
- 5.5.5 SET 22 program setting screen
- 5.5.6 Explanation of the screen display and operation of a program run
- 5.5.7 Complementary explanation of the program run
- 5.6 Explanation of the bank automatic switching function
- 6. Explanation on parameters
- 6.1 Input 1 type setting
- 6.2 Remote SV input type setting
- 6.3 Function key function setting
- 6.4 Control function setting
- 6.5 Output (from OUT 1 to OUT 7) type setting
- 6.6 Current transformer (CT) setting
- 6.7 DI setting
- 6.8 Timer function setting
- 6.9 Communication function setting
- 6.10 Initial setting
- 6.11 Priority screen setting
- 6.12 Bank function setting
- 6.13 PROGRAM FUNCTION SETTING
- 6.14 PROGRAM SETTING
- 6.15 BANK AUTOMATIC SWITCHING FUNCTION SETTING
- 7. Appendix
- 7.1 Product specifications
- 7.2 Accessories
- 7.3 Error (abnormality) display
- 7.4 Troubleshooting
- 7.5 Setting list
- 7.5.1 Run mode
- 7.5.2 Input 1 setting mode (SET 01)
- 7.5.3 Input 2 setting mode (SET 02)
- 7.5.4 Key function setting mode (SET 03)
- 7.5.5 Control setting mode (SET 04) (1/4)
- 7.5.6 OUT 1 and 2 setting modes (SET 05 and 06) (1/3)
- 7.5.7 OUT 3 to 7 setting modes (SET 07, 08, 09, 10 and 11) (1/2)
- 7.5.8 CT setting mode (SET 12)
- 7.5.9 DI setting mode (SET 13)
- 7.5.10 Timer 1 to 3 setting modes (SET 14, 15 and 16)
- 7.5.11 Communication setting mode (SET 17)
- 7.5.12 Initial setting mode (SET 18)
- 7.5.13 Priority screen setting mode (SET 19)
- 7.5.14 Bank setting mode (SET 20)
- 7.5.15 Program function setting mode (SET 21)
- 7.5.16 Program setting mode (SET 22)
- 7.5.17 Bank automatic switching function setting mode (SET 23)
48-7009-E 6-81
■Bank Automatic Switching Source Setting
ＳＥｔ２３
ＺｂＮＫ
Setting Contents
Initial
Value
2
ｂＡＳ
Bank Automatic Switching Source Setting 3
00
Function
*0
Select SV value
*1
Select ramp SV value
*2
Select PV value
Control Mode Interlock Function
0*
All Mode
1*
RUN/MAN Mode Only
2*
RUN Mode Only
※Select the source for the SV value to which the
Bank Automatic Switching will be done.
※When “SET04 bANKH=0”, the setting will be
invalid.
There will be no indication either.
※２ Bank Automatic Switching Source Setting (bAS)
Select source to which the Bank Automatic Switching will be done. Switch the bank in accordance with
the source selected.
Setting Range：When 0, select SV Value ＜Local and Remote (only Option Y)＞
：When 1, select ramp SV value.
：When 2, select PV value
NOTE: The behavior of AT (Auto-Tuning) when (bAF = 1).
・ Regardless of the source setting to which the Bank Automatic Switching will be done, it will select
SET04(SV). After the completion of the AT (Auto-Tuning), it will go back to Bank Automatic
Switching Source Setting (bAS).
・In case the Zone Threshold＊Setting (PM＊) is set, at the same time the parameter (P, I, D) is set to the
bank, the PID value obtained from the AT (Auto-Tuning) will be reflected to the Bank No. according to
the threshold.