User Manual
Table Of Contents
- TTM-200ｼﾘｰｽﾞﾕｰｻﾞｰｽﾞﾏﾆｭｱﾙ 英語 48-7009-Ｄ.pdfから挿入したしおり
- TOP
- Contents
- 2. Installation
- 3. Wiring
- 4. Basic operation
- 5. Operating the equipment
- 5.1 Precautions on operating the equipment
- 5.2 Operating monitor display
- 5.3 How to set run settings
- 5.4 How to set each function and description of function
- 5.5 Explanation of the program run function
- 5.5.1 Operation flow of the program run
- 5.5.2 SET 21 program function setting
- 5.5.3 SET 21 program function setting screen
- 5.5.4 SET 22 program setting
- 5.5.5 SET 22 program setting screen
- 5.5.6 Explanation of the screen display and operation of a program run
- 5.5.7 Complementary explanation of the program run
- 5.6 Explanation of the bank automatic switching function
- 6. Explanation on parameters
- 6.1 Input 1 type setting
- 6.2 Remote SV input type setting
- 6.3 Function key function setting
- 6.4 Control function setting
- 6.5 Output (from OUT 1 to OUT 7) type setting
- 6.6 Current transformer (CT) setting
- 6.7 DI setting
- 6.8 Timer function setting
- 6.9 Communication function setting
- 6.10 Initial setting
- 6.11 Priority screen setting
- 6.12 Bank function setting
- 6.13 PROGRAM FUNCTION SETTING
- 6.14 PROGRAM SETTING
- 6.15 BANK AUTOMATIC SWITCHING FUNCTION SETTING
- 7. Appendix
- 7.1 Product specifications
- 7.2 Accessories
- 7.3 Error (abnormality) display
- 7.4 Troubleshooting
- 7.5 Setting list
- 7.5.1 Run mode
- 7.5.2 Input 1 setting mode (SET 01)
- 7.5.3 Input 2 setting mode (SET 02)
- 7.5.4 Key function setting mode (SET 03)
- 7.5.5 Control setting mode (SET 04) (1/4)
- 7.5.6 OUT 1 and 2 setting modes (SET 05 and 06) (1/3)
- 7.5.7 OUT 3 to 7 setting modes (SET 07, 08, 09, 10 and 11) (1/2)
- 7.5.8 CT setting mode (SET 12)
- 7.5.9 DI setting mode (SET 13)
- 7.5.10 Timer 1 to 3 setting modes (SET 14, 15 and 16)
- 7.5.11 Communication setting mode (SET 17)
- 7.5.12 Initial setting mode (SET 18)
- 7.5.13 Priority screen setting mode (SET 19)
- 7.5.14 Bank setting mode (SET 20)
- 7.5.15 Program function setting mode (SET 21)
- 7.5.16 Program setting mode (SET 22)
- 7.5.17 Bank automatic switching function setting mode (SET 23)
48-7009-E 6-83
■Zone Threshold Switching Sensitivity Range Setting
ＳＥｔ２３
ＺｂＮＫ
Setting Contents
Initial
Value
4
ＡＳＣ
Zone Threshold Switching Sensitivity Range Setting 3
2
During Temperature Input
0～999（0．0～999．9）（℃）
During Analog Input
0～9999（digit）
※Sets the sensitivity setting for the threshold of
the bank auto-switching.
At bAF=0(OFF) and bAS=*0 or *1, there will
be nol indication when the SET02 LR=0.
※When SET04 bANKH=0, the setting becomes
invalid.
There will be no indications either.
※４ Zone Threshold Switching Sensitivity Range Setting (ASC)
Sets the Sensitivity Range to each intermediate points to which the bank auto-switching is done.
Setting Range： During the Temperature Input 0～999（0．0～999．9）（℃）
During the Analog Input 0～9999（digits）
NOTE: With Threshold (PM 1 to PM 7), it will be common value.
NOTE: It will be ±(ASC/2) with (PM1 to PM7) as the center.
As for the behavior, please refer to the “Zone Threshold Switching Sensitivity Range Setting
Behavior Diagram” below.
■Zone Threshold Switching Sensitivity Range Setting Behavior Diagram
With each PM＊Value as the center, the value set by ASC shall be the sensitivity range.
Auto-Swiｔching
Source
BANK0
BANK1
BANK2
BANK3
BANK4
BANK5
BANK6
BANK7
ＰＭ１
ＰＭ2
ＰＭ3
ＰＭ4
ＰＭ5
ＰＭ6
ＰＭ7
SLH
SLL
PM*
(*=1~7)
Magnified
Drawing
ＡＳＣ
When
"increasing"
Auto-Swiｔching
Source
When
"decreasing"
Outset of
BANK
switching
Outset of
BANK
switching
Auto-Swiｔching
Source
NOTE: This setting is effective only when the Bank Automatic Switching Source Setting (bAS) is selected
either Remote SV or PV.
＜Conditions when ASC can be set＞
When (bAS = 2)
When SET02 (LR = 1, 2) at (bAS = 0)
＜Conditions when ASC cannot be set＞
When (bAS = 1)
(bAS = 0) but when SET02 (LR = 0).