User Manual
Table Of Contents
- TTM-200ｼﾘｰｽﾞﾕｰｻﾞｰｽﾞﾏﾆｭｱﾙ 英語 48-7009-Ｄ.pdfから挿入したしおり
- TOP
- Contents
- 2. Installation
- 3. Wiring
- 4. Basic operation
- 5. Operating the equipment
- 5.1 Precautions on operating the equipment
- 5.2 Operating monitor display
- 5.3 How to set run settings
- 5.4 How to set each function and description of function
- 5.5 Explanation of the program run function
- 5.5.1 Operation flow of the program run
- 5.5.2 SET 21 program function setting
- 5.5.3 SET 21 program function setting screen
- 5.5.4 SET 22 program setting
- 5.5.5 SET 22 program setting screen
- 5.5.6 Explanation of the screen display and operation of a program run
- 5.5.7 Complementary explanation of the program run
- 5.6 Explanation of the bank automatic switching function
- 6. Explanation on parameters
- 6.1 Input 1 type setting
- 6.2 Remote SV input type setting
- 6.3 Function key function setting
- 6.4 Control function setting
- 6.5 Output (from OUT 1 to OUT 7) type setting
- 6.6 Current transformer (CT) setting
- 6.7 DI setting
- 6.8 Timer function setting
- 6.9 Communication function setting
- 6.10 Initial setting
- 6.11 Priority screen setting
- 6.12 Bank function setting
- 6.13 PROGRAM FUNCTION SETTING
- 6.14 PROGRAM SETTING
- 6.15 BANK AUTOMATIC SWITCHING FUNCTION SETTING
- 7. Appendix
- 7.1 Product specifications
- 7.2 Accessories
- 7.3 Error (abnormality) display
- 7.4 Troubleshooting
- 7.5 Setting list
- 7.5.1 Run mode
- 7.5.2 Input 1 setting mode (SET 01)
- 7.5.3 Input 2 setting mode (SET 02)
- 7.5.4 Key function setting mode (SET 03)
- 7.5.5 Control setting mode (SET 04) (1/4)
- 7.5.6 OUT 1 and 2 setting modes (SET 05 and 06) (1/3)
- 7.5.7 OUT 3 to 7 setting modes (SET 07, 08, 09, 10 and 11) (1/2)
- 7.5.8 CT setting mode (SET 12)
- 7.5.9 DI setting mode (SET 13)
- 7.5.10 Timer 1 to 3 setting modes (SET 14, 15 and 16)
- 7.5.11 Communication setting mode (SET 17)
- 7.5.12 Initial setting mode (SET 18)
- 7.5.13 Priority screen setting mode (SET 19)
- 7.5.14 Bank setting mode (SET 20)
- 7.5.15 Program function setting mode (SET 21)
- 7.5.16 Program setting mode (SET 22)
- 7.5.17 Bank automatic switching function setting mode (SET 23)
48-7009-E 7-6
(6) Communication
Communication is in the use exclusively from loader communication.
1) Communication specification RS-485 (1:31)
2) Communication terminal RS-485 dedicated terminal
3) Protocol TOHO 100-model protocol/MODBUS (RTU)/MODBUS (ASCII)
4) Information direction Half-duplex
5) Synchronization system Asynchronous
6) Transmission code ASCII
7) Interface RS-485 (2-wire)
8) Communication speed 2400/4800/9600/19200/38400 bps
9) Communication distance 500 m
10) Response delay time 0 - 250 ms
11) Character
① Start bit 1 bit fixed
② Stop bit 1/2 bits
③ Data length 7/8 bits
④ Parity None/odd No./even No.
⑤ BCC check Nonexistent/existent * For MODBUS setting, BCC check is
ineffective
⑥ Address 1 - 99 stations * For MODBUS setting, 1 - 247 stations
12) Isolation Isolated from power circuit and CPU circuit
13) Connection method Terminal block
(7) Loader communication
Loader communication is in the use exclusively from communication.
1) Communication specification TTL (1:1)
2) Communication terminal Loader communication dedicated terminal
3) Protocol TOHO 100-model protocol/MODBUS (RTU)/MODBUS (ASCII)
4) Information direction Half-duplex
5) Synchronization system Asynchronous
6) Transmission code ASCII
7) Interface TTL level
8) Communication speed 2400/4800/9600/19200/38400 bps
8) Response delay time 0 - 250 ms
10) Character
① Start bit 1 bit fixed
② Stop bit 1/2 bits
③ Data length 7/8 bits
④ Parity None/odd No./even No.
⑤ BCC check Nonexistent/existent
* For MODBUS setting, BCC check is ineffective
⑥ Address 1 - 99 stations
* For MODBUS setting, 1 - 247 stations
11) Isolation Isolated from power circuit and non-isolated from CPU circuit
12) Connection method 2.5, 3-pin mini-jack
(8) Display and operation section
1) Measurement value display section
LCD display (with LED back light and emission colors of red, green and orange)
TTM-204/205 5-digit Character height of 10 mm
TTM-207 5-digit Character height of 13 mm
TTM-209 5-digit Character height of 20 mm
2) Setting value display section
LCD display (with LED back light and emission colors of red)
TTM-204/205 5-digit Character height of 8 mm
TTM-207 5-digit Character height of 8 mm
TTM-209 5-digit Character height of 10 mm
3) Auxiliary display section
LCD display (with LED back light and emission colors of green)
TTM-204/205 1-digit Character height of 8 mm
TTM-207 1-digit Character height of 8 mm
TTM-209 1-digit Character height of 10 mm
4) LCD lamp
LCD display (with LED back light and emission colors of red)