User Manual
Table Of Contents
- TTM-200ｼﾘｰｽﾞﾕｰｻﾞｰｽﾞﾏﾆｭｱﾙ 英語 48-7009-Ｄ.pdfから挿入したしおり
- TOP
- Contents
- 2. Installation
- 3. Wiring
- 4. Basic operation
- 5. Operating the equipment
- 5.1 Precautions on operating the equipment
- 5.2 Operating monitor display
- 5.3 How to set run settings
- 5.4 How to set each function and description of function
- 5.5 Explanation of the program run function
- 5.5.1 Operation flow of the program run
- 5.5.2 SET 21 program function setting
- 5.5.3 SET 21 program function setting screen
- 5.5.4 SET 22 program setting
- 5.5.5 SET 22 program setting screen
- 5.5.6 Explanation of the screen display and operation of a program run
- 5.5.7 Complementary explanation of the program run
- 5.6 Explanation of the bank automatic switching function
- 6. Explanation on parameters
- 6.1 Input 1 type setting
- 6.2 Remote SV input type setting
- 6.3 Function key function setting
- 6.4 Control function setting
- 6.5 Output (from OUT 1 to OUT 7) type setting
- 6.6 Current transformer (CT) setting
- 6.7 DI setting
- 6.8 Timer function setting
- 6.9 Communication function setting
- 6.10 Initial setting
- 6.11 Priority screen setting
- 6.12 Bank function setting
- 6.13 PROGRAM FUNCTION SETTING
- 6.14 PROGRAM SETTING
- 6.15 BANK AUTOMATIC SWITCHING FUNCTION SETTING
- 7. Appendix
- 7.1 Product specifications
- 7.2 Accessories
- 7.3 Error (abnormality) display
- 7.4 Troubleshooting
- 7.5 Setting list
- 7.5.1 Run mode
- 7.5.2 Input 1 setting mode (SET 01)
- 7.5.3 Input 2 setting mode (SET 02)
- 7.5.4 Key function setting mode (SET 03)
- 7.5.5 Control setting mode (SET 04) (1/4)
- 7.5.6 OUT 1 and 2 setting modes (SET 05 and 06) (1/3)
- 7.5.7 OUT 3 to 7 setting modes (SET 07, 08, 09, 10 and 11) (1/2)
- 7.5.8 CT setting mode (SET 12)
- 7.5.9 DI setting mode (SET 13)
- 7.5.10 Timer 1 to 3 setting modes (SET 14, 15 and 16)
- 7.5.11 Communication setting mode (SET 17)
- 7.5.12 Initial setting mode (SET 18)
- 7.5.13 Priority screen setting mode (SET 19)
- 7.5.14 Bank setting mode (SET 20)
- 7.5.15 Program function setting mode (SET 21)
- 7.5.16 Program setting mode (SET 22)
- 7.5.17 Bank automatic switching function setting mode (SET 23)
48-7009-E 7-9
7.2 Accessories
7.2.1 Current transformer
★ Current transformer is used to measure current values of a heater through connecting it to TOHO’s
digital controller TTM-200 series and the heater.
Model: CTL-6-P-H-(S)
Product specifications
Current applicable
0.1 - 80.0 A rms (50/60 Hz)
* This is specification for CT main frame.
Max. allowable current
80 A rms continuous
Withstand voltage
2000 VAC for a minute (between through-hole and output terminal)
Isolation resistance
500 VDC, 100 M or larger (between through-hole and output terminal)
Use temperature range
-20 to 70 °C
Storage temperature range
-30 to 90 °C
Weight
Approx. 16 g
Accessories
None
Outside dimension
7.2.2 Loader cable
★ Loader cable is used to connect TOHO’s digital controller TTM-200 series and a personal computer
(PC) and such so that various values are set and read on the PC, using the dedicated loader software
installed on it.
Model: TTM-LOADER
Product specifications
OS to meet
Windows XP
USB I/F standards
In compliance with USB Specification 2.0
DTE speed
Up to 38400 bps
Connector specification
PC side: USB
Controller side: 2.5 mm stereo jack
Consumption current
90 mA
Use temperature range
0 to 50 °C
Use humidity range
20 to 90 %RH (no dew condensation allowed)
Storage temperature range
-10 to 60 °C (no freeze or dew condensation allowed)
Storage humidity range
5 to 95 %RH (no dew condensation allowed)
Power supply voltage
Bus-powered (to be supplied from PC side)
Weight
40 g
Outside dimension
USB connector
Stereo plug