User Manual
Table Of Contents
- TTM-200ｼﾘｰｽﾞﾕｰｻﾞｰｽﾞﾏﾆｭｱﾙ 英語 48-7009-Ｄ.pdfから挿入したしおり
- TOP
- Contents
- 2. Installation
- 3. Wiring
- 4. Basic operation
- 5. Operating the equipment
- 5.1 Precautions on operating the equipment
- 5.2 Operating monitor display
- 5.3 How to set run settings
- 5.4 How to set each function and description of function
- 5.5 Explanation of the program run function
- 5.5.1 Operation flow of the program run
- 5.5.2 SET 21 program function setting
- 5.5.3 SET 21 program function setting screen
- 5.5.4 SET 22 program setting
- 5.5.5 SET 22 program setting screen
- 5.5.6 Explanation of the screen display and operation of a program run
- 5.5.7 Complementary explanation of the program run
- 5.6 Explanation of the bank automatic switching function
- 6. Explanation on parameters
- 6.1 Input 1 type setting
- 6.2 Remote SV input type setting
- 6.3 Function key function setting
- 6.4 Control function setting
- 6.5 Output (from OUT 1 to OUT 7) type setting
- 6.6 Current transformer (CT) setting
- 6.7 DI setting
- 6.8 Timer function setting
- 6.9 Communication function setting
- 6.10 Initial setting
- 6.11 Priority screen setting
- 6.12 Bank function setting
- 6.13 PROGRAM FUNCTION SETTING
- 6.14 PROGRAM SETTING
- 6.15 BANK AUTOMATIC SWITCHING FUNCTION SETTING
- 7. Appendix
- 7.1 Product specifications
- 7.2 Accessories
- 7.3 Error (abnormality) display
- 7.4 Troubleshooting
- 7.5 Setting list
- 7.5.1 Run mode
- 7.5.2 Input 1 setting mode (SET 01)
- 7.5.3 Input 2 setting mode (SET 02)
- 7.5.4 Key function setting mode (SET 03)
- 7.5.5 Control setting mode (SET 04) (1/4)
- 7.5.6 OUT 1 and 2 setting modes (SET 05 and 06) (1/3)
- 7.5.7 OUT 3 to 7 setting modes (SET 07, 08, 09, 10 and 11) (1/2)
- 7.5.8 CT setting mode (SET 12)
- 7.5.9 DI setting mode (SET 13)
- 7.5.10 Timer 1 to 3 setting modes (SET 14, 15 and 16)
- 7.5.11 Communication setting mode (SET 17)
- 7.5.12 Initial setting mode (SET 18)
- 7.5.13 Priority screen setting mode (SET 19)
- 7.5.14 Bank setting mode (SET 20)
- 7.5.15 Program function setting mode (SET 21)
- 7.5.16 Program setting mode (SET 22)
- 7.5.17 Bank automatic switching function setting mode (SET 23)
48-7009-E 3-9
★ AI input (current and voltage only)
TTM-205
Terminal Nos. ⑰ and ⑱
TTM-207
Terminal Nos. ⑨ and ⑩
TTM-209
Terminal Nos. ⑰ and ⑱
TTM-207 TTM-205/209
* AI input is optional.
(TTM-204 is not equipped with AI input.)
* Provide input signal lines distant from power supply lines, power lines or load lines so as not to affect
input signal lines with noise induction.
★ CT (current detector) input
TTM-204
Terminal Nos. ⑮, ⑯, ⑰ and ⑱
TTM-205
Terminal Nos. ⑬, ⑭, ⑮ and ⑯
TTM-207
Terminal Nos. ⑲, ⑳, ○
21
and ○
22
TTM-209
Terminal Nos. ⑬, ⑭, ⑮ and ⑯
* When the event input (DI 1 or
DI 2) is selected, CT 1 or CT 2
are not selectable.
* When the event input (DI 2) is
selected, CT 2 is not selectable.
* When the event input (DI 1 or
DI 2) is selected, CT 1 or CT 2
are not selectable.
* When the event input (DI 2) is
selected, CT 2 is not selectable.
TTM-204
TTM-207
TTM-205/209
* CT input is optional.
* Heater disconnection failure is detected by CT (current detector) when the heater disconnection alarm
is effective.
* CT possible to be used is “CTL-6-P-N”
* Max. 2 points are selectable (to be designated at order placement).
* CT input is not selectable for analog output.