User Manual
Table Of Contents
- TTM-200ｼﾘｰｽﾞﾕｰｻﾞｰｽﾞﾏﾆｭｱﾙ 英語 48-7009-Ｄ.pdfから挿入したしおり
- TOP
- Contents
- 2. Installation
- 3. Wiring
- 4. Basic operation
- 5. Operating the equipment
- 5.1 Precautions on operating the equipment
- 5.2 Operating monitor display
- 5.3 How to set run settings
- 5.4 How to set each function and description of function
- 5.5 Explanation of the program run function
- 5.5.1 Operation flow of the program run
- 5.5.2 SET 21 program function setting
- 5.5.3 SET 21 program function setting screen
- 5.5.4 SET 22 program setting
- 5.5.5 SET 22 program setting screen
- 5.5.6 Explanation of the screen display and operation of a program run
- 5.5.7 Complementary explanation of the program run
- 5.6 Explanation of the bank automatic switching function
- 6. Explanation on parameters
- 6.1 Input 1 type setting
- 6.2 Remote SV input type setting
- 6.3 Function key function setting
- 6.4 Control function setting
- 6.5 Output (from OUT 1 to OUT 7) type setting
- 6.6 Current transformer (CT) setting
- 6.7 DI setting
- 6.8 Timer function setting
- 6.9 Communication function setting
- 6.10 Initial setting
- 6.11 Priority screen setting
- 6.12 Bank function setting
- 6.13 PROGRAM FUNCTION SETTING
- 6.14 PROGRAM SETTING
- 6.15 BANK AUTOMATIC SWITCHING FUNCTION SETTING
- 7. Appendix
- 7.1 Product specifications
- 7.2 Accessories
- 7.3 Error (abnormality) display
- 7.4 Troubleshooting
- 7.5 Setting list
- 7.5.1 Run mode
- 7.5.2 Input 1 setting mode (SET 01)
- 7.5.3 Input 2 setting mode (SET 02)
- 7.5.4 Key function setting mode (SET 03)
- 7.5.5 Control setting mode (SET 04) (1/4)
- 7.5.6 OUT 1 and 2 setting modes (SET 05 and 06) (1/3)
- 7.5.7 OUT 3 to 7 setting modes (SET 07, 08, 09, 10 and 11) (1/2)
- 7.5.8 CT setting mode (SET 12)
- 7.5.9 DI setting mode (SET 13)
- 7.5.10 Timer 1 to 3 setting modes (SET 14, 15 and 16)
- 7.5.11 Communication setting mode (SET 17)
- 7.5.12 Initial setting mode (SET 18)
- 7.5.13 Priority screen setting mode (SET 19)
- 7.5.14 Bank setting mode (SET 20)
- 7.5.15 Program function setting mode (SET 21)
- 7.5.16 Program setting mode (SET 22)
- 7.5.17 Bank automatic switching function setting mode (SET 23)
48-7009-E 4-28
Continued from the previous page
Hold MODE key pressed for 3 seconds.
Holding the MODE key pressed for 3 seconds in any
screen above results in changing the screen.
Use the ▲/▼ key to change
the item to be displayed.
(Some items are not
displayed depending on the
equipment specification.)
Use the MODE key to change
the item to be displayed.
(Some items are not
displayed depending on the
equipment specification.)
Use the MODE key to change
the item to be displayed.
(Some items are not displayed
depending on the equipment
specification.)
MODE key
MODE key
MODE key
MODE key
MODE key
* Each SET item is also set for blind setting after moving the screen to the
parameter screen, using the MODE key.
* Always use the FUNC key to set screens for the blind settings.
When the character “OFF” in the lower row (red) is displayed, the
screen is in a blind state.
* Holding the MODE key pressed for 3 seconds in each screen results in
returning to .
* How to terminate the blind setting mode
1) After turning the power off, turn it back on. After the initial screen is displayed, the operating mode screen is
displayed again.
2) Holding the MODE key pressed for 3 seconds in each SET screen moves the screen to the PV/SV blind setting
screen.
Then, holding the MODE key pressed for about 10 seconds results in displaying the operating mode screen again.
* In the diagram above, only SET1 and SET20 are shown; other SET** are skipped.
The blind status of each parameter can also be settable for other SET**.