Topic： User Manual of TomTom HD Traffic Receiver Module 1 US Doc No： Ver： 1.
Topic： User Manual of TomTom HD Traffic Receiver Module 1 US Document History Version 1.0 Date Oct. 21, 2008 Brief Description New established Page 2 of 39 Doc No： Ver： 1.
Topic： User Manual of TomTom HD Traffic Receiver Module 1 US Doc No： Ver： 1.1 Page： 3 / 39 FCC Regulations: z This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Topic： User Manual of TomTom HD Traffic Receiver Module 1 US Doc No： Ver： 1.1 Page： 4 / 39 Warning: The maximum antenna gain allowed for use with this device is -0.81 dBi. When the module is installed in the host device, the FCC ID label must be visible through a window on the final device or it must be visible when an access panel, door or cover is easily removed.
Topic： User Manual of TomTom HD Traffic Receiver Module 1 US Doc No： Ver： 1.1 Page： 5 / 39 Table of Contents 1. INTRODUCTION ............................................................................................................................. 6 2. GENERAL PRODUCT DESCRIPTION .......................................................................................... 7 2.1 SIM Card Holder Support ...................................................................................................
Topic： 1. User Manual of TomTom HD Traffic Receiver Module 1 US Doc No： Ver： 1.1 Page： 6 / 39 Introduction HD Traffic Receiver Module is a GPRS modem module. It is a small, lightweight, low power consumption and RoHS compliant device that allow digital communication services wherever a GSM 850, PCS 1900 network is present. The module is provided with a 20-pin board-to-board connector. Power input connector is necessary when link the modem PCB.
Topic： 2. User Manual of TomTom HD Traffic Receiver Module 1 US Doc No： Ver： 1.1 Page： 7 / 39 General Product Description 2.1 SIM Card Holder Support The HD Traffic Receiver Module 1 US has on the backside of the PCB, the necessary pads to manually solder a SIM card holder. The type of the SIM card holder to be used is UNCR2103D006-0 of JESS-LINK. 2.
Topic： Doc No： User Manual of TomTom HD Traffic Receiver Module 1 US Ver： 1.1 Power off current (Typical) <= 60 uA Stand-by current (GSM idle) <= 4 mA Operating current in GSM channel <= 300 mA Operating current in GPRS class 10 <= 500 mA Page： 8 / 39 2.4 SIM reader The HD Traffic Receiver Module 1 US support phase 2 GSM11.14 - SIM 1.8V/3V volts. 2.5 Data transmission The HD Traffic Receiver Module 1 US supports GPRS Class 10, MS Class B. 2.
Topic： Doc No： User Manual of TomTom HD Traffic Receiver Module 1 US Ver： 1.1 Input high level 1.6 V 3.3 V Input low level 0V 0.4 V Output high level 1.65 V 2.2 V Output low level 0V 0.35 V Page： 9 / 39 2.7 Reset signal RESET signal is used to reset the HD Traffic Receiver Module 1 US . Whenever this signal is pulled low, the module is reset.
Topic： Doc No： User Manual of TomTom HD Traffic Receiver Module 1 US Output voltage Ver： 2.76 V 2.85 V 1.1 Page： 10 / 39 2.93 V Output current 50 mA Output bypass capacitor 2.2 uF 2.9 Connector interface 2.9.1 Board-to-board connector interface PIN Definition GND 1 2 GND Vpower 3 4 Vpower Vpower 5 6 Vpower GND 7 8 GND SYS_EN 9 10 VIO GND 11 12 GND EXTRSTN 13 14 CTS GND 15 16 RTS NC 17 18 RXD NC 19 20 TXD 2.9.
Topic： Doc No： User Manual of TomTom HD Traffic Receiver Module 1 US Ver： 1.1 Page： 11 / 39 12 GND PWR GSM Power Supply Ground 13 EXTRSTN I External reset CMOS compatible 3.3V External HW reset 14 CTS I Asynchronous Interface 0 CMOS compatible 3.3V RTS (DCE) 15 GND PWR GSM Power Supply Ground 16 RTS O Asynchronous Interface 0 Serial CMOS compatible 3.3V CTS (DCE) 17 NC 18 RXD I Asynchronous Interface 0 Serial CMOS compatible 3.
Topic： User Manual of TomTom HD Traffic Receiver Module 1 US Doc No： Ver： 1.1 Page： 12 / 39 2.12.1 GSM–850 The Module in GSM–850 operating mode are class 4 in accordance with the specifications that determine the nominal 2W peak RF power (+33dBm) on 50-Ohm load. 2.12.2 PCS –1900 The module in PCS–1900 operating mode are class 1 in accordance with the specifications that determine the nominal 1W peak RF power (+30dBm) on 50-Ohm load. 2.13 Reference sensitivity 2.13.
Topic： Doc No： User Manual of TomTom HD Traffic Receiver Module 1 US Ver： 1.1 Page： 13 / 39 2.15 Power up / down scenarios In general, be sure not to turn on the module while it is out of the operating range of voltage in Chapter 2.2. 2.15.1 Turn on the module The module can be activated via SYS_EN signal. When switch on the Module the SYS_EN signal needs to be driven to high level for at least 150ms 2.15.
Topic： User Manual of TomTom HD Traffic Receiver Module 1 US Doc No： Ver： 1.1 Page： 14 / 39 When the module is in POWER OFF mode the application interface is switched off and must not be fed from any other source. Therefore, your application must be designed to avoid any current flow into any digital pins of the application interface. 2.15.4 Inserted and removal action direction These models are made very thin so that they may be smaller in size and light in weight than before.
Topic： User Manual of TomTom HD Traffic Receiver Module 1 US Page 15 of 39 Doc No： Ver： 1.
Topic： User Manual of TomTom HD Traffic Receiver Module 1 US Page 16 of 39 Doc No： Ver： 1.
Topic： Doc No： User Manual of TomTom HD Traffic Receiver Module 1 US Ver： 1 2 Page 17 of 39 1.
Topic： Doc No： User Manual of TomTom HD Traffic Receiver Module 1 US Ver： 1.1 Page： 18 / 39 1 2 3 1 2 Select the COM port that you have installed “CP210x_VCP_Win2K_XP_S2K3” driver. For example: COM3 in the installation demo.
Topic： User Manual of TomTom HD Traffic Receiver Module 1 US Your modem has been set up for the first step. Next step, we will run advanced setting of modem. Page 19 of 39 Doc No： Ver： 1.
Topic： User Manual of TomTom HD Traffic Receiver Module 1 US Page 20 of 39 Doc No： Ver： 1.
Topic： User Manual of TomTom HD Traffic Receiver Module 1 US Doc No： Ver： 1.1 Page： 21 / 39 1 2 Typing into “at+cgdcont=1, “ip”, “internet” for extra initialization commands. This command allows to specify specific PDP context parameter values for a PDP context.
Topic： User Manual of TomTom HD Traffic Receiver Module 1 US 1 2 Please make sure that the flow control is “None”. Page 22 of 39 Doc No： Ver： 1.
Topic： User Manual of TomTom HD Traffic Receiver Module 1 US Doc No： Ver： 1 2 Please make sure that hardware settings are the same as above. Page 23 of 39 1.
Topic： User Manual of TomTom HD Traffic Receiver Module 1 US Please make sure maxmun port speed to be 115200. Page 24 of 39 Doc No： Ver： 1.
Topic： User Manual of TomTom HD Traffic Receiver Module 1 US Doc No： Ver： 1.1 3.4 Network setting Double click “Network and Dial-up Connections” icon to run network setting.
Topic： User Manual of TomTom HD Traffic Receiver Module 1 US Page 26 of 39 Doc No： Ver： 1.
Topic： User Manual of TomTom HD Traffic Receiver Module 1 US Page 27 of 39 Doc No： Ver： 1.
Topic： Doc No： User Manual of TomTom HD Traffic Receiver Module 1 US Ver： 1 2 3 4 Please type “*99#” into phonebook number. Page 28 of 39 1.
Topic： User Manual of TomTom HD Traffic Receiver Module 1 US Doc No： Ver： 1.1 Type the name you want to use for this connection.
Topic： User Manual of TomTom HD Traffic Receiver Module 1 US Doc No： Ver： 1.1 Page： 30 / 39 Pressing the right button of mouse on “Prague” connection icon, you need to change the properties.
Topic： User Manual of TomTom HD Traffic Receiver Module 1 US Doc No： Ver： 1.1 Page： 31 / 39 1 2 3 4 All hardware features of modem protocol should be disabled. Now, you have completed all modem and network setting. You can use Section 2.3 to dial up network directly in the future.
Topic： User Manual of TomTom HD Traffic Receiver Module 1 US Doc No： Ver： 1.1 3.5 Dial-up network by HD Traffic Receiver 1 US Pressing “Prague” icon to dial up network. Keep empty for user name and password.
Topic： User Manual of TomTom HD Traffic Receiver Module 1 US Page 33 of 39 Doc No： Ver： 1.
Topic： User Manual of TomTom HD Traffic Receiver Module 1 US Doc No： Ver： 1.1 Page： 34 / 39 3.6 How to setup Hyper Terminal for AT commands Run Hyper Terminal from Windows XP Start->Programs->Accessories->Communications->Hyper Terminal Set the name for connection (e.g. “MI01_connection”), then press OK Select the PC serial port (for example COM2) , then press OK Select the appropriate setting for MI01 data modem serial port setting; then select APPLY/OK.
Topic： User Manual of TomTom HD Traffic Receiver Module 1 US Doc No： Ver： 1.1 Page： 35 / 39 If the HD Traffic Receiver module is power up, you type AT then the response must be OK.
Topic： User Manual of TomTom HD Traffic Receiver Module 1 US Doc No： Ver： 1.1 Page： Annex A - AT command set for HD Traffic Receiver Module 1.
Topic： User Manual of TomTom HD Traffic Receiver Module 1 US Mute control +CMUT Call meter maximum event +CCWE Set greeting text +CSGT Automatic Time Zone Update +CTZU Time Zone Reporting +CTZR Report mobile termination error +CMEE List all available AT commands +CLAC 6. Phonebook commands Select phonebook memory storage +CPBS Read phonebook entries +CPBR Find phonebook entries +CPBF Write phonebook entry +CPBW 7.
Topic： User Manual of TomTom HD Traffic Receiver Module 1 US Doc No： Ver： 10.
Topic： User Manual of TomTom HD Traffic Receiver Module 1 US Doc No： Ver： 1.1 Page： 39 / 39 GPRS attach or detach +CGATT PDP context activate or deactivate +CGACT Enter data state +CGDATA Automatic response to a network request for PDP context activation +CGAUTO Show PDP address +CGPADDR GPRS mobile station class +CGCLASS GPRS network registration status +CGREG Select service for MO SMS messages +CGSMS 13.
