TomTom LINK 510 Installation Guide
. What’s in the box What’s in the box a TomTom LINK 510 A Yellow LED for indication of the connection status B Green LED for indication of the system status C GSM antenna connector (SMB) for optional use of an external GSM antenna D Service/Update Mini-USB-cable connector E Power cable connector F Reset button G IO-Cable connector H GPS antenna connector (SMB) for optional use of an external GPS antenna b Power cable c Holder d Fixatives - 2 cable ties, 2 adhesive strips, 2 self-tapping screws and a c
. Before the Installation Before the Installation Congratulations You have chosen the TomTom LINK 510, a core hardware component of TomTom WORKsmart fleet management solutions. With WORKsmart from TomTom Business Solutions you are always connected to your people on the road in a smart and easy way. TomTom LINK 510 is a GPS receiver and GSM/GPRS module in one unit, always providing the vehicle’s current position.
. Safety first Safety first Important safety notices and warnings Important: Read the following safety instructions carefully TomTom Business Solutions accept no liability for damage that results from disregard for the safety instructions. This document is part of the product. Keep it in a safe place. If you pass the unit on to a new user, make sure you give them this document as well.
Repairs must be carried out by authorised and qualified personnel only. Never replace damaged parts of the unit yourself. Give the defective unit to TomTom Business Solutions. Only the qualified staff of TomTom Business Solutions are authorised to repair or replace parts. • Warning - damage to the device Short-circuits inside the unit can be caused by contact with water or other liquids. The unit may be damaged by contact with water. Use and store the unit in an area protected from water.
5. Find the right Place Find the right Place First you need to find the right place to install your LINK 510. To find the right place take the following into consideration: • Do not expose the LINK 510 to direct sunlight and/or high temperature for longer periods to ensure proper operation. • The top side of the device must not be obstructed by metal items to ensure GPS reception using the integrated GPS receiver.
6. Connection overview Connection overview * Make sure this wire is fused with max. 10 A.
7. Connecting to power Connecting to power Connect the LINK 510 to the vehicle power supply with the standard vehicle voltage (12 V / 24 V). Do not connect to a voltage converter. The three wires GND, IGN and PWR+ (supply voltage) must be connected. Important: Follow the order of connecting the wires as described below. First connect the wires then insert the plug into the LINK 510.
8. Activating LINK 510 Activating LINK 510 After you have installed your LINK 510 in the vehicle activate the LINK 510 using the TomTom LINK Activation Tool. You can also activate your LINK 510 using a TomTom PRO navigation device, see Connecting to PRO and WEBFLEET on page 15. 1. Install the latest version of the TomTom LINK Activation Tool. You can download the Activation Tool from the Partner Portal on our website https:// business.tomtom.com/10001/areas/reseller/index.xml.
7. Enter the Activation Code, which you find in your WEBFLEET contract confirmation. 8. Click OK. The progress of the activation and a successful activation are shown.
9. Mounting LINK 510 Mounting LINK 510 Your LINK 510 comes with an integrated GSM antenna and an integrated GPS antenna. Depending on the place you choose for the installation, you can install your LINK 510 without external antennas. To learn how to use external antennas with the LINK 510, see Appendix: Using external antennas on page 22. • The LINK 510 must be placed unobstructed by metal objects. • The device must not interfere with clear vision for the driver.
Note: The full strength of the strips will be reached after approx. 72 hours depending on the temperature. 7. Insert the LINK 510 into the holder. Press gently until it clicks into place. Attaching the holder using the self-tapping screws You can use the two self-tapping screws to affix the holder in the vehicle. 1. Choose a flat surface for the LINK 510. Remember, when the LINK 510 is in the holder, it must not be obstructed by metal objects. 2.
10. Testing operation Testing operation Apart from the tests described below you can test the operation of your LINK 510 using the TomTom Business Solutions Diagnostic Tool via Bluetooth. Power/Ignition test Before testing the connection to power and to ignition make sure you have carried out the steps described in the previous chapters. 1. Please check all connections to the LINK 510 (wires, fuses etc.). 2. Turn off the ignition. The green LED must be off and shortly on every 3 seconds. 3.
11. Connecting to PRO and WEBFLEET Connecting to PRO and WEBFLEET Connect your navigation device to your LINK 510 to fully enjoy the benefits of your WORKsmart solution. To use a TomTom PRO navigation device in combination with the LINK 510 a corresponding WEBFLEET subscription is required. When you first switch on your navigation device, you are asked to connect it with the LINK 510 installed in your vehicle. You can do this immediately or at any time later. 1.
8. Select the appropriate vehicle type. If you select Truck or Bus, you have to enter your vehicle dimensions If you have properly connected the two devices, you will receive a welcome message from WEBFLEET confirming the activation. In future the connection is established automatically. To check the connection status between the two devices, tap WORK in the main menu on your navigation device, then tap Connection status.
12. Diagnostics Diagnostics Monitoring operation Monitor the system operation of LINK 510 through the green system LED according to the table below. For detailed diagnostics use the TomTom Business Solutions Diagnostic Tool. You can download the Diagnostic Tool from the Partner Portal on our website https:// business.tomtom.com/10001/areas/reseller/index.xml. Go to Techinical Support and select Activation and Diagnostics. GREEN LED mode OFF Unit is in standby mode or is not connected to power.
Monitor the connection of the LINK 510 to the GSM network and to TomTom WEBFLEET through the yellow connection LED according to the table below. For detailed diagnostics always use the TomTom Business Solutions Diagnostics Tool. YELLOW LED mode OFF Not connected - No GSM coverage. • Check if device is connected to power, see Connecting to power on page 8. Switch on ignition. • Leave dead spot. OFF and shortly ON every 3sec Not connected - Correct GSM operator not avaialable.
13. Reset LINK 510 Reset LINK 510 If the LINK 510 does not operate properly or signals a system error (see Diagnostics on page 17) you may need to restart or reset the unit. Only restart or reset the LINK 510 after you have made sure you have carried out all previously described steps without success. Restarting your LINK To restart your LINK 510 press the reset button with a thin pointed object until it clicks and keep it pressed for 1 to 2 seconds.
14. Technical data Technical data Dimensions Body: 121 x 56.5 x 21.5 mm Body with Holder: 121 x 68 x 25.5 mm Weight Body: 88 g Holder: 12 g Material Body and holder: Injection moulded plastic PC/ABS Protection class IP 20 Supply voltage 12 V / 24 V (min. 9 V to max.
GPS antenna connector for external GPS antenna (optional accessory) SMB (male) - (antenna - female) Supply voltage range 3.3 V Minimum antenna gain at 3 V: 20 dB Maximum antenna gain: 40 dB Maximum noise rating: 1.
15. Appendix: Using external antennas Appen dix: Using external antennas Mounting external GPS antenna If you install the LINK 510 in a place where it has poor GPS reception, you need to use the external GPS antenna accessory from TomTom Business Solutions, Art. no 9UKE.001.00, which comes with an integrated magnet and an adhesive pad. The external GPS antenna from TomTom Business Solutions is not part of the standard LINK 510 product package.
3. Prepare a smooth, clean, oil free and dry surface in the windscreen. 4. Attach the antenna to the prepared surface so that the top side has clear view of the sky. Either locate a smooth metal surface or use the extra adhesive pad. Mounting external GSM/GPRS antenna If you install the LINK 510 in a place where it has poor GSM/GPRS reception, you need to use the external GSM/GPRS antenna accessory from TomTom Business Solutions, Art. no. 9KLE.001.03, which comes with an adhesive pad.
16. Appendix - Using the IO cable Appen dix Using the IO cable You can connect the IO cable from TomTom Business Solutions, Art. no. 9KLE.001.02, to the IO cable connector of the TomTom LINK 510. With it you can read information from a digital tachograph, record inputs e.g. for keeping digital logbook with the help of a switch, reporting times the vehicle is idling, retrieving FMS/CANbus data etc. a CAN High (Orange/Black) For FMS data retrieval. b CAN Low (Orange/Brown) For FMS data retrieval.
If the tachograph with the covered connectors is sealed, the seal must only be removed by an authorised tachograph installer. Using the input IN 2 for idle time reporting LINK 510 can report idle times to WEBFLEET when the engine is running for longer than five minutes and the vehicle is not moving. This requires configuration in TomTom WEBFLEET. The input IN 2 must be connected to a signal indicating the activity of the engine, e.g. alternator, engine, etc.
input between plus and minus (ground GND) of the vehicle electrical system voltage (+9 ... 30V). If no change-over switch is available, an electric load (e.g. indicator light, resistor) between the digital input and ground (GND) or between the digital input and the vehicle voltage (+9 ... 30V) can offer defined levels. When using inductive loads, a free-wheeling diode must be used in parallel with the load.
Wiring the digital output The digital output OUT of the LINK 510 is an open drain output linking to ground. The connected load must be connected between vehicle voltage and OUT. Loads requiring more than 0.35 A must be controlled with relays. If the load requires more than the maximum output voltage use a 12 V/24 V relay, depending on the operating voltage. Caution Do not switch safety relevant vehicle functions.
17. Addendum Addendum CE-Declaration of Conformity The unit described in this document is in accordance with the official European directives. A copy of the declaration of conformity can be provided on request. This equipment complies with the essential requirements of EU Directive 99/5/EC. The GPRS-modem integrated in this product has been pre-certified separately and is marked with CE0681. FCC-ID:S4LLINK500 This device complies with Part 15 of the FCC Rules.
License Agreement and limited warranty apply to this product. You can review it at www.tomtom.
