MSDS

ManualsBrandsToner Plastics Manuals3D Printer Filaments & AccessoriesPremium 3D Printer Filament, ABS, 1 kg, 1.75 mm, Natural

Toner Plastics ABS 3D Printer Filament Page 1 of 6 Rev. 10/06/2015

Material Safety Data Sheet

In accordance with 29 CFR 1910.1200, ANSI Z400.1-2004, and ISO 11014-1: 1994.

1. IDENTIFICATION

Product name: ABS 3D Printer Filament

Product Use: For use in 3D printing machines

Supplier: Toner Plastics Inc., 35 Industrial Drive, East Longmeadow, MA 01028

Emergency telephone numbers (24 hours a day): (413) 525-2369

2. HAZARDS IDENTIFICATION

Most Important Hazards: None

Adverse Human Health Effects: None

Environmental Effects: None

Physical and Chemical: None

3. COMPOSITION / INFORMATION ON INGREDIENTS

Substance or Preparation: Substance

Chemical Name: Acrylonitrile-Butadiene-Styrene Copolymer

Content:

 CAS No. 9003-56-9: > 98% Styrene-acrylonitrile-butadiene copolymer

 CAS No. 100-42-5: < 0.1% Styrene

Additional information: Does not contain dangerous substances above limits that

need to be mentioned in this section according to applicable legislation.

4. FIRST AID MEASURES

Inhalation: In case of gases evolving from melted filament, move subject to fresh

air. Treat symptomatically.

Skin Contact: Wash with water. In case of melted filament, wash affected skin

area and clothing with plenty of (soap and) water. Seek medical advice.

Eye Contact: In case of small particles, flush with plenty of water for at least 15

minutes. Seek medical advice if any small particles still remain. In case of gases

evolving from melted filament of high temperature, flush with plenty of water for

at least 15 minutes. Seek medical advice if necessary.

Summary of content (6 pages)

PAGE 1
Material Safety Data Sheet In accordance with 29 CFR 1910.1200, ANSI Z400.1-2004, and ISO 11014-1: 1994. 1. IDENTIFICATION Product name: ABS 3D Printer Filament Product Use: For use in 3D printing machines Supplier: Toner Plastics Inc., 35 Industrial Drive, East Longmeadow, MA 01028 Emergency telephone numbers (24 hours a day): (413) 525-2369 2. HAZARDS IDENTIFICATION Most Important Hazards: None Adverse Human Health Effects: None Environmental Effects: None Physical and Chemical: None 3.
PAGE 2
Ingestion: Induce vomiting. Rinse mouth with water. Seek medical advice if necessary. 5. FIRE-FIGHTING MEASURES Extinguishing Media: Water, Foam, Dry chemical powder Special Fire-Fighting Procedure: Self-contained breathing apparatus Fire and Explosion Hazards: None 6. ACCIDENTAL RELEASE MEASURES Methods for Cleaning up: Recovery if not contaminated or disposal Personal Precautions: Strands/string remaining on ground may cause slipping; provide adequate ventilation.
PAGE 3
100-42-5 Styrene USA: ACGIH-BEI, blood 0.2 mg/L Styrene in venous blood End of exposure or end of shift USA: ACGIH-BEI, urine 400 mg/g creatinine Mandelic acid + phenylglyoxylic acid End of exposure or end of shift Ventilation: Necessary for fumes and gases when melting. Personal Protection Eyes: Wear safety glasses or chemical goggles for general purpose. Respiratory: Wear appropriate respiratory masks as needed. Gloves: Necessary for handling melted material.
PAGE 4
Acute toxicity (inhalation): Lack of data. No evidence of acute toxicity. Skin corrosion/irritation: Lack of data. Dust: Can cause skin, eye and respiratory tract irritation. Processing, thermal hazards: Vapors: Can cause skin, eye and respiratory tract irritation. Eye damage/irritation: Lack of data. Dust: Can cause skin, eye and respiratory tract irritation. Processing, thermal hazards: Vapors: Can cause skin, eye and respiratory tract irritation.
PAGE 5
Styrene: Harmful if inhaled. Causes damage to organs through prolonged or repeated exposure. May be fatal if swallowed and enters airways. Causes serious eye irritation. Causes skin irritation. Symptoms: Dust: Can cause skin, eye and respiratory tract irritation. The melted product can cause severe burns. Thermal treatment, Processing: Irritating to eyes, respiratory system and skin. In case of ingestion: Swallowing may cause gastrointestinal irritation and pain of guts. 12.
PAGE 6
Reason for revision: Created Revision date: 10/6/2015 Recommended restrictions: None Prepared by: Toner Plastics, Inc. The information herein is given in Good faith, but no warranty, express or implied, is made. Consult the company for further information.