241-9881 1/2'' IMPACT WRENCH
WARNING PLEASE READ THESE INSTRUCTIONS CAREFULLY AND KEEP FOR FUTURE REFERENCE WARNING:Read all safety warnings and instructions. Use the 120V Impact Wrench in accordance with these instructions, taking into account the working conditions and the work to be performed. Using this power tool for purposes other than those intended could result in rendering your vehicle in an unsafe condition and may result in serious injury or death. Where possible, dress appropriately.
WARNING The 120V Impact Wrench is not a toy. Children should be supervised to ensure they do not play with the tool. Keep the tool, any attachment and its power cord out of reach of children. Do not use the tool for anything other than its intended use. SAFE USAGE Do not use the power tool if the switch does not turn off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
WARNING with wet hands. Before connecting the tool to the power supply ensure the voltage corresponds to the voltage limits on the rating plate. Only use TOOL SHOP Brands recommended attachments or those specifically designed for use with the unit. Do not operate the tool if it has been submerged in water or any other liquid, to prevent against electric shock, damage and potential injury. Do not use the tool if the power cord is damaged.
SAFETY SYMBOLS The following safety symbols may appear on this product. Please ensure you understand their meanings before operating this tool in order to prevent personal injury and avoid damage to the tool. SPECIFICATION ■ Voltage: 120 Volts , 60 Hz. ■ Current rating: 2.4 Amp ■ No load speed: 4800 RPM ■ Max Torque: 370ft.
INSTALLING THE SOCKET CAUTION When removing the socket or bit from the tool, avoid contact with skin and use proper protective gloves when grasping the socket, bit or accessory. Accessories may be hot after prolonged use.When installing a socket, align the holes in the side of the socket with the dent pin. Press the socket on until the dent pin engages in the hole. To remove the socket, pull the socket off the driveshaft.
REMOVING LUG NUTS recommended by the vehicle manufacturer. 6. Set the Directional Lever to “REV” and carefully loosen the lug nuts. Remove in the order recommended by the manufacturer. 7. If the Impact Wrench cannot loosen the lug nut, use a breaker bar (not included) to break the nut loose before trying again. 8. Remove wheel. WARNING: Do not get under the vehicle without jack stands. Jacks are not designed to maintain heavy loads for long periods of time. 1. Lift wheel back into place. 2.
MAINTENANCE & CARE products from entering the plastic casing. The chemicals they contain could corrode or damage the plastic. Immediately wipe grease and oil-based grime off the tool and accessories with a slightly damp cloth. Store idle power tools out of reach of children and do not allow people unfamiliar with the power tool or these instructions to operate the 120V Impact Wrench.
PARTS LIST Part Description Qty Part Description Qty 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 7 1 1 1 1 2 2 2 1 1 1 1 1 1 3 1 1 1 4 4 4 1 1 1 1 1 1 1 1 1 1 1 2 1 1 4 1 1 1 8 1 1 2 1 1 1 ST screw 4*16 Right housing Ball bearing 606Z Insulated washer Stator Brush holder Copper bush Carbon brush Rotor Ball bearing 626Z Motor gear Gear box Washer Annular gear Planetary gear Gear output shaft Bearing bush Gear cap ST screw 3*16 Screw Spring washer Holding plate Operating lever 24 25 26
SCHEMATIC DRAWING 10
TOOL SHOP® 1/2'' IMPACT WRENCH WARRANTY 1-YEAR LIMITED WARRANTY: This TOOL SHOP® brand power tool carries a 1-Year Limited Warranty to the original purchaser. If the tool fails within one (1) year from the date of purchase, simply bring this tool with your original sales receipt back to your nearest MENARDS® retail store.