208-2198 1-3/4" COIL ROOFING NAILER Operator’s Manual SAVE THIS MANUAL You will need this manual for safety instructions, operating procedures and warranty. Put it and the original sales receipt in a safe dry place for future reference.
IMPORTANT SAFETY INSTRUCTIONS INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS. WARNING! When using tools, basic precautions should always be followed, including the following. ! WORK AREA Keep the work area clean and well lit. Cluttered benches and dark areas increase the risk of electric shock, fire, and injury to persons. Do not operate the tool in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust.
IMPORTANT SAFETY INSTRUCTIONS ! WARNING! Remove finger from the trigger when not driving fasteners. Never carry the tool with finger on trigger, the tool may fire a fastener. TOOL USE AND CARE Know this tool. Read manual carefully, learn its application and limitations, as well as the specific potential hazards related to this tool. Use only fasteners listed in the Accessories section of this manual.
IMPORTANT SAFETY INSTRUCTIONS Always assume the tool contains fasteners. Respect the tool as a working implement; no horseplay. Always keep others at a safe distance from the work area in case of accidental discharge of fasteners. Do not point the tool toward yourself or anyone whether it contains fasteners or not. Accidental triggering of the tool could result in death or serious personal injury. Do not drop or throw the tool.
IMPORTANT SAFETY INSTRUCTIONS Use only a pressure-regulated compressed air source to limit the air pressure supplied to the tool. The regulated pressure must not exceed 110 PSI. If the regulator fails, the pressure delivered to the tool must not exceed 120 PSI. The tool could explode which will cause death or serious personal injury. Always disconnect air resource: a) Before making adjustments. b) When servicing the tool. c) When clearing a jam. d) When tool is not in use.
OPERATING PROCEDURES SETUP AIR SOURCE The TOOL SHOP 1-3/4” coil roofing nailer is designed to operate on clean, dry, compressed air, regulated at 70-110 PSI. The preferred system would include a filter, a pressure regulator, and an automatic oiler located as close to the tool as possible. Within 15 feet (5 m) is ideal. Do not use bottled air or gases. Please see below: Regulator 1-3/4" coil roofing nailer Air connector Air hose Quick coupling Oiler Filter Fig.
OPERATING PROCEDURES LOADING NAILS ! CAUTION: Do not load with contact safety mechanism or trigger depressed. Fig.4 1. Push down on the latch 1 (Fig.4), swing the latch 1 (Fig.5), then open the movable cover 2 (Fig.4). 1 2 Fig.5 2. Open the magazine cover. ( Fig.6 ) 1 Fig.6 3. Check the adjuster plate 1 (Fig.6) inside the magazine. Then rotate the adjuster nut to adjust the platform to match the nail length: a. the lowest position: 1-1/2” to 1-3/4” long nails b.
OPERATING PROCEDURES Complete all the steps in PREPARING THE TOOL before using. Please Note: This tool is fired in only one way: BUMP FIRE: The tool should only fire if the Safety Nosepiece is pressed against the workpiece and the trigger is pulled. It should fire again if the trigger is released and pulled OR if the safety is lifted and pressed against the workpiece again. The tool should not fire if the Safety Nosepiece is not pressed against an object. Fig.8 1.
TROUBLESHOOTING PROBLEM CAUSE SOLUTION Air leak at trigger area O-ring in trigger valve damaged or cracked Check and replace O-ring Trigger valve head damaged Check and replace trigger valve head Trigger valve stem, seal, or O-ring damaged Check and replace trigger valve stem Air leak between body and front plate Piston O-ring or bumper damaged Check and replace O-ring or bumper Air leak between body and cylinder cap Screw loose Tighten screws Damaged seal Check and replace seal Worn bump
PARTS LIST ITEM NO. DESCRIPTION PCS ITEM NO. DESCRIPTION PCS ITEM NO. DESCRIPTION PCS Pin 1 1 Screw 5*16 1 41 Catch Guide Plate 1 81 2 Washer 1 42 Spring 1 82 Pin 3*12 1 3 O-Ring 16*1.
SCHEMATIC DRAWING ! WARNING Repairs should be made by an authorized repair center.Do not open or disassemble this power tool.
TOOL SHOP 12 1-3/4" COIL ROOFING NAILER WARRANTY