Instructions
Operating elements
1
6
2 3 4 5
1 Push button
2 Switch lever
3 Rough scale
4 Precise scale
5 End piece
6 Square drive (not depicted)
Torque setting
• Pull down the end piece (5) until it clicks into place.
• Adjust the torque by rotating the end piece.
You can read the set value on the rough scale (3).
You can set the torque to an exact 0.4 Nm (item no. 1525064) or 0.2 Nm (item no.
1525319) value with the help of the precise scale (4).
• Push the end piece back toward the handle until it clicks into place.
Do not over-wind the end piece. The torque value must be within the setting range.
Usage
Do not use the torque wrench with adapters for other square sizes. Use a socket
wrench insert that ts the square drive (6) without adapter only.
• Press and hold the push button (1) and insert a suitable wrench socket on the square drive.
Release the push button to lock the wrench socket.
• Select the rotational direction (left or right) using the switch lever (2).
• Now tighten the screw/nut/bolt slowly and evenly with the torque wrench until you hear
a clicking noise from the torque wrench and simultaneously feel a mechanical motion,
indicating that the torque has been reached.
• Loosen the torque wrench fully after use.
If the torque wrench is not loosened, this may cause the actual torque to deviate
signicantly from the scale in the long run.
Maintenance and cleaning
• The product does not require any maintenance, therefore never disassemble it. Servicing or
repair may be carried out only by a specialist.
• Use a dry, lint-free cloth to clean the product.
Disposal
Always dispose of the product according to the relevant statutory regulations.
Technical data
Torque range ................................ 3 - 15 Nm (item no. 1525064)
6 - 30 Nm (item no. 1525319)
Accuracy ....................................... ±4 % (clockwise)
±6 % (counter-clockwise)
Drive ............................................. 6.3 mm (1/4″)
Dimensions (L x W x H) ................ 205 x 29 x 22 mm (item no. 1525064)
236 x 29 x 23 mm (item no. 1525319)
Weight .......................................... 260 g (item no. 1525064)
300 g (item no. 1525319)
Operating instructions
6.3 mm (1/4”) Torque wrench
Item no. 1525064 (3 - 15 Nm)
Item no. 1525319 (6 - 30 Nm)
Intended use
The product is intended only for tightening screws, nuts or bolts. The torque can be adjusted
between 3 to 15 Nm (item no. 1525064) or 6 to 30 Nm (item no. 1525319).
The product has been calibrated according to DIN EN ISO 6789.
For safety reasons, you must not rebuild and/or modify this product. Using the product for
purposes other than those described above may damage the product. Improper use may also
result in safety hazards for the user. Read the instructions carefully and store them in a safe
place. Make this product available to third parties only together with its operating instructions.
This product complies with statutory national and European regulations. All company and
product names are trademarks of their respective owners. All rights reserved.
Package contents
• Torque wrench
• Case
• Operating instructions
Up-to-date operating instructions
Download the latest operating instructions at www.conrad.com/downloads or scan the QR code
on this page. Follow the instructions on the website.
Explanation of symbols
This symbol is used to highlight important information in these operating instructions.
Always read this information carefully.
This symbol indicates special information and advice on how to use the product.
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on
proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the warranty/
guarantee.
• This product is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may become
dangerous playing material for children.
• Always check the product for any damage before use. If you notice any damage,
do not use the product any longer.
• When using the torque wrench, observe your country’s relevant safety and
accident prevention regulations.
• Do not use any lever extension (to increase the leverage while working with the
torque wrench). Doing so will result in damage to the torque wrench.
Do not use any attachments with joints, either, as these may affect the torque
value.
Do not overload the torque wrench. The torque wrench may not be used to loosen
screws, nuts or bolts.
Never use the torque wrench as a striking tool, this will destroy it.
• Attach the torque wrench to the screw/nut/bolt at a right angle only. Do not tilt
it, otherwise this will lead to a wrong torque when tightening the screw/nut/bolt.
• Hold the torque wrench only by its handle when tightening a screw, nut or bolt.
• Protect the torque wrench from humidity, dust and dirt, oil or chemicals during
operation or storage. Never drop the torque wrench to prevent damage or
destruction.
• The torque wrench is a hand tool calibrated by the manufacturer. For this reason,
it must be handled with care.
• If you have any reason to assume that the torque wrench is inaccurate/decalibrated
(e. g. after being dropped), cease use immediately.
• In schools, educational centres, hobby and self-help workshops, the use of the
product is to be supervised by trained employees.
• If you have questions which remain unanswered by these operating instructions,
contact our technical support service or other technical personnel.
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microlming, or the capture in
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represents the technical status at the time of printing.
Copyright 2017 by Conrad Electronic SE. *1525064_319_V1_0317_02_IPL_m_en