Instructions
Operating Elements
180°
180°
90°
90°
1
12
1
2
3
4
5
6
7
8
9
10
11
1 Lens cover
2 Lamp head adjust lock
3 Upper arm
4 Lower arm
5 DC input jack
6 Lamp attachment plug
7 Clamp socket
8 Base clamp
9 Clamp screw
10 Lens
11 LED ring light
12 Power ON/OFF
Installation
The lamp arms (3) and (4) are spring loaded, open carefully when removing from
packaging. Make sure not to trap your fingers and hands when adjusting them.
Do not use force to over tighten the clamp screw (9) as this may damage the base
clamp (8) and surface it is attached to.
Ensure that the surface attached to the desk clamp has parallel edges. The desk
clamp must not be attached to desks with chamfered or tapered edges.
Make sure the lamp is securely held in place before letting go.
The jaws on the base clamp (8) may leave marks or scratch sensitive surfaces.
a) Attach Clamp
• Loosen the clamp screw (9).
• Slide the clamp onto the horizontal surface.
• Tighten the clamp screw.
b) Connect Lamp to Base
• Insert the lamp attachment plug (6) into the clamp socket (7).
• Gently check to make sure the connection is secure before letting go.
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights
including translation reserved. Reproduction by any method, e.g. photocopy, microlming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication
represents the technical status at the time of printing.
Copyright 2019 by Conrad Electronic SE. *1967204_v1_0419_02_dh_m_en
Operation
The upper arm (3) and lower arm (4) are spring loaded and can be adjusted within
the specified ranges. Over adjusting or using excessive force may cause damage.
Please hold the base clamp (8) while making adjustments to prevent the lamp from
falling over.
• Connect the power adaptor cable to the DC input jack (5) and the other end to a mains power
supply.
• Flip the lens cover (1) open.
• Touch the power ON/OFF (12) button to turn the LED ring light (11) ON/OFF.
Touch and hold the power (12) button to increase/decrease brightness.
• Adjust the lamp head to the desired position.
• Close the lens cover (1) after use.
Care and cleaning
• Always disconnect the product from the power supply before cleaning it.
• Remove loose particles from the lens with clean compressed air.
• Clean the surface of the lens with a lens cloth or a soft, lint-free cloth.
• Never use aggressive detergents, rubbing alcohol or other chemical solutions, as these could
damage the housing or stop the product from functioning properly.
Disposal
Electronic devices are recyclable waste and must not be placed in household
waste. At the end of its service life, dispose of the product according to the relevant
statutory regulations.
You thus fulfill your statutory obligations and contribute to protection of the
environment.
Technical data
a) General
Operating voltage ......................... 12 V/DC, max 7 W
Material ......................................... Lamp: ABS, Aluminum Alloy, Steel
Clamp: ABS
Protection class ............................ III
Clamp ........................................... max. 44 mm
Dimmable ..................................... Yes
Energy efficiency class ................. (A to A++)
Light controls ................................ Capacitive touch
Lens material ................................ Acrylic
Lens size ...................................... ø110 mm
Diopter .......................................... 5D (2.25x)
Operating conditions ..................... 10 to 40 °C, 0 – 85 % relative humidity
Storage conditions ........................ 0 to 50 °C, 0 – 85 % relative humidity
Dimensions (W x H x D) ............... 180 x 1030 x 50 mm
Weight .......................................... 507 g (main unit), 81 g (clamp), 72 g (adapter)
b) LED
Quantity ........................................ 72 pcs
Type .............................................. SMD
Brightness ..................................... max. 880 lm
Lux ................................................ 3300 lux (magnifier glass focal length)
Colour temperature ....................... 6000 K
Life ................................................ 25000 h
Power ........................................... 7 W
c) Power adapter
Input voltage/current ..................... 100 - 240 V/AC, 50/60 Hz
Output voltage/current .................. 12 V/DC, 1000 mA