User Manual

- 7 -
nuts: (11) 4-40 hex nuts (7-clevis jam nuts,
4-cowl reinforcements)
(6) 1/4-20 blind nuts (factory-installed – 4-engine
mounting, 2-wing bolts)
(4) 2-56 hex nuts (tail gear door brackets) (3) 0-80 hex nuts (2-ball link balls on tail steering
arm, 1-throttle on engine)
washers: (6) #2 washers (4-wheel covers, 2-fuel tank floor) (4) #4 washers (4-cowl mounting) (4) #4 lock washers (4-cowl mounting) other: (2) 3/8" [9.5mm] heat shrink tubing (for servo
extensions)
(1) 1/2" [13mm] heat shrink tubing (for servo
extensions)
(16) silicone retainers (clevises) (1) 2" x 9" [50 x 230mm] CA hinge strip (3) 0-80 ball link balls (2-tail steering arm, 1-throttle) (4) size 10 rubber bands (tail gear doors) (1) 32 oz. [960cc] Great Planes fuel tank and
hardware
(2) #64 rubber bands (for fuel tank mounting) (1) 2-56 x 1" [25mm] threaded rod (throttle pushrod) (2) Decal sheets (1) Velcro
®
strap
(2) plywood air tank mounting rings (1) plywood air tank former (2) 2" x 2" [50 x 50mm] plywood wing bolt plates
(w/1/4" hole)
(6) plywood air line guides (1) plywood air valve mount (6) 1/16" x 7/8" [1.5 x 22mm] plywood cowl
reinforcements (for mounting screws)
(6) 1/2" x 13/16" x 13/16" [12 x 20 x 20mm]
hardwood cowl mounting blocks
(8) 3/8" x 13/16" x 13/16" [10 x 20 x 20mm]
hardwood servo mounting blocks
(8) 1/2" x 1/2" x 7/8" [13 x 13 x 23mm] wheel cover
mounts (4 req’d., 4 spares)
(1) hardwood “L” block (for tail gear door) (2) 1/16" [2mm] plywood large rubber band hooks
(with spacer)
(2) 1/16" [2mm] plywood small rubber band hook
(with spacer)
(2) 3/8" x 1-3/4" [10mm x 45mm] hardwood
wing dowels
(2) plywood aft servo trays (2) plywood forward servo trays (1) plywood fuel tank mount (2) bent aluminum tail gear door brackets (4) nylon pinned hinges (for tail gear doors) (1) 1/8" x 1/4" x 2" [3 x 6 x 50mm] balsa stick (for
gluing on instrument panel)
(1) 1/4" x 1/4" x 12" [6 x 6 x 300mm] hardwood
stick (for forward servo tray)
(1) 1/16" x 3/8" x 1-9/16" [1 x 10 x 40mm] plywood
tail gear door stop
(1) 1/8" x 12" hardwood dowel (for cowl mount blocks) (2) 3/4" x 3/4" x 7" [20 x 20 x 180mm] balsa sticks
(for gluing on engine exhaust stacks)
Cockpit parts (photographed) instrument panel floor seat bottom seat back right panel left panel wing joiner Pull/Pull cable contents: (1) Steel cable (4) Copper tubes (swages) (2) 2mm metal clevises (2) 2mm brass couplers (2) 2mm nuts Fixed landing gear components: (2) 5" [125mm] main wheels (2) landing gear mounts (4) metal straps (8) 3 x 10mm screws (2) main landing gear wires (4) 6mm wheel collars (3) 1/8" wheel collars (8) 3mm set screws
tail gear mount tail gear wire 2" [45mm] tail wheel steering arm 1.5mm hex wrench
ORDERING REPLACEMENT PARTS
To order replacement parts for the Top Flite Giant P-51D Mustang ARF, use the order numbers in the Replacement Parts List that follows. Replacement parts are available only as listed. Not all parts are available separately (an aileron cannot be purchased separately, but is only available with the wing kit). Replacement parts are not available from Product Support, but can be purchased from hobby shops or mail order/Internet order firms. Hardware items (screws, nuts, bolts) are also available from these outlets. If you need assistance locating a dealer to purchase parts, visit www.top-flite.com and click on “Where to Buy.” If this kit is missing parts, contact Product Support.
REPLACEMENT PARTS LIST
Description How to purchase Missing pieces . . . . . . . .Contact Product Support Instruction manual . . . . .Contact Product Support Full-size plans . . . . . . . . . . . . . . . . .Not available
Contact your hobby supplier
to purchase these items
TOPA1650 Fuse set (fuselage, wing fairings, tail
wheel doors, brackets, etc.)
TOPA1651 Wing set (ailerons, flaps, fiberglass air
scoop, guns, wheel covers)
TOPA1652 Tail set TOPA1653 Cowl (w/exhausts) TOPA1654 Cockpit kit TOPA1655 Decal set TOPA1656 Canopy