- Top Innovations, Inc. Fabric Steamer & Iron SteamFast SF-432

ManualsBrandsTop Innovations ManualsIronSF-432

by Top Innovations, Inc.

Please read all instructions before use.

Mail in your warranty registration card.

MODEL SF-432

Fabric Steamer & Iron

Top Innovations, Inc.

6655 Troost Ave.

Kansas City, MO 64131

Tel: (800) 711-6617

(816) 584-9700

www.SteamFast.com

customerservice@topinnovations.com

Printed in China

PRODUCT SERIAL NUMBER

For your convenience, space has been provided below for

you to record the serial number of your unit (located on

the back or bottom of the unit) for easy reference when

contacting our Customer Service Department.

________________ - ______________________________

V060905

Summary of content (8 pages)

PAGE 1
MODEL SF-432 Fabric Steamer & Iron Top Innovations, Inc. 6655 Troost Ave. Kansas City, MO 64131 Tel: (800) 711-6617 (816) 584-9700 www.SteamFast.com customerservice@topinnovations.com Printed in China PRODUCT SERIAL NUMBER For your convenience, space has been provided below for you to record the serial number of your unit (located on the back or bottom of the unit) for easy reference when contacting our Customer Service Department.
PAGE 2
LETTER FROM THE CEO WARRANTY INFORMATION ONE YEAR LIMITED WARRANTY Dear Valued Customer, (If outside USA, additional shipping charges may apply) Congratulations on purchasing your new SF-432 Fabric Steamer & Iron. This versatile and convenient product places the power of steam in a compact and lightweight appliance, with a practical and space-saving design that is optimized for either table-top or wall-mounted use.
PAGE 3
TROUBLESHOOTING & CUSTOMER SUPPORT PROBLEM Unit fails to heat up. Heating Indicator Light does not illuminate. POSSIBLE CAUSE SOLUTION Unit is not plugged in. Plug electrical cord into outlet. Household Circuit Breaker / Ground Fault Interrupter has tripped or blown a fuse. Reset Circuit Breaker / Ground Fault Interrupter, or replace fuse. If you need assistance, contact a licensed electrician.
PAGE 4
SPECIAL INSTRUCTIONS WARNING: To reduce the risk of electrical shock, this appliance has a three-pronged plug. This plug will fit in a polarized wall outlet only one way. If the plug does not fit fully in the outlet, contact a licensed electrician to install a proper outlet. DO NOT attempt to modify the plug or defeat this safety feature. 1. To reduce likelihood of circuit overload, DO NOT operate another high wattage appliance on the same circuit. 2.
PAGE 5
USING THE FABRIC STEAMER & IRON STEAMING GARMENTS 1. Place garment on a clean, rust-free clothes hanger. Hang within easy reach of Steam Hose / Nozzle. FABRIC STEAMER & IRON PRODUCT INFORMATION The following features and accessories are included with your Fabric Steamer & Iron. Carefully inspect Styrofoam packing material for all parts listed below. To obtain possible missing parts, refer to the Customer Support section on page 14 of this manual. 2. Point Steam Nozzle at bottom of garment.
PAGE 6
FABRIC STEAMER & IRON PRODUCT INFORMATION • The Wall-Mounting Base (1) attaches to the wall as a permanent station for mounting the Base Unit, saving space and providing quick, convenient access to the SF-432. • The Base Unit (2) is the main body of the SF-432, housing the water reservoir which is accessed for filling via the Water Reservoir Inlet. • The Water Reservoir Inlet (3) serves as the opening through which water is poured into the water reservoir.
PAGE 7
USING THE FABRIC STEAMER & IRON ASSEMBLING THE FABRIC STEAMER & IRON FILLING WATER RESERVOIR WITH WATER SECURING WALL-MOUNTING BASE TO WALL NOTE: When water level is low, it is normal for water reservoir in Base Unit to emit a pumping sound. Adding more water will eliminate the sound. CAUTION: Be sure that power cord is not connected to an electrical outlet before filling water reservoir with water.
PAGE 8
ASSEMBLING THE FABRIC STEAMER & IRON ASSEMBLING THE FABRIC STEAMER & IRON MOUNTING BASE UNIT ONTO WALL-MOUNTING BASE CONNECTING THE FABRIC BRUSH 1. Hang Steam Nozzle securely onto Steam Nozzle Hanger (FIGURE 2-A). CAUTION: Use care when connecting Fabric Brush, as Ironing Plate may be hot. Do not attempt to connect Fabric Brush while unit is emitting steam. 2. Align two holes on back of Water Reservoir with two hooks protruding from front of Wall-Mounting Base.