LXB-L15C English USER MANUAL TABLE OF CONTENTS FOR YOUR SAFETY -------------------------------------------------- 1 SAFETY PRECAUTIONS -------------------------------------- 2 SPECIAL NOTES ON LCD MONITORS ------------------- 3 BEFORE YOU OPERATE THE MONITOR --------------------- 3 FEATURES -------------------------------------------------------- 3 PACKING LIST --------------------------------------------------- 3 CONTROLS AND CONNECTORS ----------------------- 4-5 ADJUSTING THE VIEWING ANGLE -------------
Before operating the monitor please read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PRECAUTIONS l Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. l Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance. Use only a cart or stand recommended by the manufacturer or sold with the monitor. If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacturer and follow the kit instructions.
l To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate configured receptacles marked between 100 - 240V AC, Min. 3.5A. l The wall socket shall be installed near the equipment and shall be easily accessible.
SPECIAL NOTES ON LCD MONITORS The following symptoms are normal with LCD monitor and do not indicate a problem. NOTES • • • • • Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears. You may find slightly uneven brightness on the screen depending on the desktop pattern you use. The LCD screen has effective pixels of 99.99% or more. It may include blemishes of 0.
POWER CORD Power Source: 1. Make sure the power cord is the correct type required in your area. 2. This LCD monitor has an External universal power supply that allows operation in either 100/120V AC or 220/240V AC voltage area (No user adjustment is required.) 3. Connect the power cord into your LCD monitor’s power input socket, and then plug the other end into a 3-pin AC power outlet.
Figure 1 1. 2. Connecting Cables Signal Cable AC Power Cord ADJUSTING THE VIEWING ANGLE INSTALLATION INSTRUCTIONS • • • • For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor’s angle to your own preference. Hold the stand so you do not topple the monitor when you change the monitor’s angle. You are able to adjust the monitor’s angle from -3° to 20°. You can conveniently adjust the height of your monitor by slightly lifting the display.
Figure 3 NOTES • • Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen. Careful attention is required not to catch your fingers or hands when you change the angle. OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. The other control knobs are located at front panel of the monitor (See Figure 4). By changing these settings, the picture can be adjusted to your personal preferences.
Figure 4 External Control Knob EXTERNAL CONTROLS 1. / Brightness 2. / Contrast 3. Power Key /Power Indicator 4. Auto Config / Exit 5. MENU/Enter FRONT PANEL CONTROL • Power /Power indicator: Press this button to switch ON/OFF of monitor’s power. And display the monitor’s state. Green — Power on mode. Organge — Power off mode. • MENU/ENTER: Activate OSD menu or function adjusts confirmation. • Contrast / : Adjust contrast or function adjustment.
Adjust brightness or function adjustment. • Auto Config Key / EXIT: 1. When OSD menu is in active status, this knob will act as EXIT-KEY (EXIT OSD menu) 2. When OSD menu is in off status, press this knob over 1 seconds to be in Auto Adjustment function. The Auto Adjustment function is used to set the HPos, VPos, Clock and Focus automatically.
5. To exit and save the setting, press or to the exit item and press MENU-key, or leave the monitor alone for 10 seconds. 6. When the OSD window is active, it shows the input signal timing. The "H" Stands for the horizontal frequency and "V" stands for the vertical frequency. 7. Press and during the power switch on.The OSD menu will be displayed rotated by 90°, and reapeat this action, the display will come back the factory mode.
4. LANGUAGE Muti-Language selecion. 5. OSD TIMER Choose OSD window display time. 6. COLOR TEMPERATURE 6.1 7800K/6500K ( COLOR TEMPERATURE) The color temperature for 7800K is x=0.296, y=0.311 and 6500K is x=0.313, y=0.329. It presents two different color sets on the screen. You can select 7800K or 6500K by pressing MENU Key. 6.2 USER MODE ( Red / Green/ Blue ) If the 7800K normal white or 6500K warmer white do not satisfy your desire, properly adjust R .G.
The DDC1 is a unidirectional data channel from the display to the host that continuously transmits EDID information. The DDC2B is a bidirectional data channel based on the I²C protocol. The host can request EDID information over the DDC2B channel. THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF THERE IS NO VIDEO INPUT SIGNAL. IN ORDER FOR THIS MONITOR TO OPERATE PROPERLY, THERE MUST BE A VIDEO INPUT SIGNAL.
TECHNICAL SUPPORT (FAQ) Problem & Question Power LED is not on No Plug & Play Picture is fuzzy Picture bounces or a wave pattern is present in the picture The power LED is ON (orange) but there’s no video or no picture.
Screen image is not centered or *Adjust pixel frequency (CLOCK) and sized properly. FOCUS or press hot-key (AUTO) Picture has color defects *Adjust RGB color or select color (white does not look white) temperature Poor brightness or contrast *When the brightness of the screen lowers after being used for a certain period and the function of the display is affected, send it to our authorized service center for repair.
ERROR MESSAGE & POSSIBLE SOLUTION CABLE NOT CONNECTED : 1. 2. Check that the signal-cable is properly connected , If the connector is loose, tighten the connector’s screws. Check the signal-cable’s connection pins for damage. INPUT NOT SUPPORT : Your computer has been set to unsuitable display mode ,Set the computer to display mode given in the following table.
APPENDIX SPECIFICATIONS LCD Panel Input Display Colors Dot Clock Max. Resolution Plug & Play EPA ENERGY STAR® Driving system Size Pixel pitch Viewable angle Response time Video Separate Sync. H-Frequency V-Frequency ON Mode OFF Mode Input Connector Input Video Signal Maximum Screen Size Power Source Environmental Considerations Weight (N. W.) 16 TFT Color LCD 38 cm(15.0") 0.297mm( H ) x 0.297mm( V ) 120° (H) 100° (V) 40 ms R,G,B Analog Interface H/V TTL 30kHz – 61kHz 50-75Hz 16.
• • • • • • • • • • • • • • Switch External Controls: Auto Adjust Key/EXIT / Brightness / Contrast Power Key MENU/ENTER BRIGHTNESS & CONTRAST ADJUST POSITION VIDEO NOISE LANGUAGE OSD TIMER COLOR TEMPERATURE OSD POSITION EXIT OSD RESET UL, FCC, TCO’9 5 Functions Regulatory Compliance 17
FACTORY PRESET TIMING TABLE STANDARD VGA SVGA XGA HORIZONTAL FREQUENCY RESOLUTION VERTICAL FREQUENCY 640 × 480 31.469kHz 59.94Hz 640 × 480 37.861kHz 72.809Hz 640 × 480 37.50kHz 75Hz 800 × 600 35.156kHz 56.25Hz 800 × 600 37.879kHz 60Hz 800 × 600 48.077kHz 72.188Hz 800 × 600 46.875kHz 75Hz 1024 × 768 48.363kHz 60Hz 1024 × 768 56.476kHz 70.069Hz 1024 × 768 60.023kHz 75.029Hz CONNECTOR PIN ASSIGNMENT 1 6 10 5 11 15 15 - Pin Color Display Signal Cable PIN NO. 1. 2. 3.
