WSDB-673GN Hardware & Software Setup Guide Rev. 0.1 Proprietary & Confidential Information Doc.
1. WLAN Function Quick Start Guide Physical hardware configuration likes as figure1. Please follow the following procedure step by step to get starting WLAN function. SDIO Board Software setup: Follow driver installation procedure steps to install the GB9662 driver on your PC (OS: XP). 1-1.Copy WDSB-673GN\WSDB-673GN_Driver_V1.2_10122012\Nvram\GB9662_NVRAM_V1.1_09132 012.TXT to C:\Windows\system32\Drivers 1-2. Copy Test Board Socket WDSB-673GN\WSDB-673GN_Driver_V1.2_10122012\5_90_153_49_43362_mfg_A2(Dr
1-4.Choose No, not now, and then click Next. 1-5.Choose install from a list or specific location (Advanced), and then click Next. Proprietary & Confidential Information Doc.
1-6.Choose Don’t search, I will choose driver to install, and then click Next. 1-7.Click Have Disk . Proprietary & Confidential Information Doc.
1-8.Click Browse to choose correct directory of Driver WDSB-673GN\WSDB-673GN_Driver_V1.2_10122012\5_90_153_49_43362_m fg_A2(Driver) \bcmsddhd.inf and then click OK to next step. 1-9.Choose Broadcom 802.11g Network Adapter and click Next to install driver. Proprietary & Confidential Information Doc.
1-10.Click Finish and you can check the device is working fine in Device Manager. 1-11.In Device Manager, Choose Broadcom 802.11g Network Adapter right button of mouse and then choose content. Proprietary & Confidential Information Doc.
1-12.In the tab of Advanced, choose 1-13.In the tab of Advanced, choose 43362ROMImagePatch item and replace with \SystemRoot\system32\drivers\ GB9662_NVRAM_V1.1_09132012.TXT and then click OK button. Proprietary & Confidential Information Doc.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna, 3) For all products market in US, OEM has to limit the operation channels in CH1 to CH11 for 2.4G band by supplied firmware programming tool. OEM shall not supply any tool or info to the end-user regarding to Regulatory Domain change.
Industry Canada statement: This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
Tant que les 2 conditions ci-dessus sont remplies, des essais supplémentaires sur l'émetteur ne seront pas nécessaires. Toutefois, l'intégrateur OEM est toujours responsable des essais sur son produit final pour toutes exigences de conformité supplémentaires requis pour ce module installé.
IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate Canada authorization.
final quant à la façon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intègre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises et avertissements comme indiqué dans ce manuel.
