Product Guide
Power on: press and hold for 2s until you hear the ‘power on’ prompt
voice.
Rugged speaker comes with a lithium-ion battery. For best result, fully
charge Rugged speaker before use. (recommended output of charging
device is 1A)
To charge, plug the micro USB cable into Rugged speaker and plug the
standard USB connector into your device into your power source ( If
power source is Laptop, Desktop, much more charging time(5-6 hours)
will be needed)
While charging the LED solid Red, fully charged, light off.
Power off: press and hold for 2s until you hear the ‘power off’ prompt
voice and LED light off.
In paring mode but not connected beyond 5 mins, the Rugged speaker
will power off automatically.
First press and hold for 2s until you hear the ‘power on’ prompt voice,
the Blue LED will come on and blink. This means Rugged speaker is in
pairing mode, make sure Bluetooth is enabled on your audio source
and in a few moments, pairing name 'WIRELESS SPEAKER' will appear
on your list, then press it to connect, the LED will flash blue every 5
seconds which means you are paired.
Solid Blue
60X60MM
light off
Charging always
lights red light
Model:21YX06
PRODUCT GUIDE
Ver.01
What’s in box
30cm USB charging cable x1
Bluetooth version：V5.0
Product size：102mm(H) X 63mm(W)
Pairing name: 21YX06
Speaker diameter：52mm
Microphone_Sensitivity: -42 ± 3dB at 1mw 1kHz
Operating range： 10m
Battery capacity of earbuds: 1200mAh
Working hour: upper than 10 hours
Charging time: about 3 hrs
Bluetooth profile:HFP A2DP HSP AVRCP
FCC ID: 2AKI18-BLTSPK
Manual x1
Rugged speaker x1
Power on/o
Bluetooth paring
Phone call
Play music
ash blue
Blue light
blink
Reject a call
Press & hold for 1s
Play/pause music
Press and hold to adjust
previous/ next song.
Volume+ &-：Single click
Charging
5-6 hours
About 4 hours
FCC Statement
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules, these
limits are designed to provide reasonable protection against harmful
interference in a residential installation, this equipment generates uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions. May cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
X1 X1
X1 X1
Volume+ &-：Single click
X1
WIRELESS SPEAKER
Rugged Speaker
Trouble Shooting and Common Situations
Rugged Speaker cannot power on
Battery drain, please charge the device for 30 minutes, and then
powering on.
Rugged Speaker will be disconnected from time to time
1. The battery drain.
2. The Rugged Speaker is beyond the communication range(10m).
No sound on talking mode
1. Confirmed the Rugged Speaker connected to earpiece mode on
talking.
2. Try to volume up Rugged Speaker or smart phone.
No sound with music playing
1. Try to volume up Speaker or smart phone.
2. Rugged Speaker disconnected with smart phone，please
reconnected again.
Cannot charger for Rugged Speaker
1. The charger cable connected not well.
2. Charger line was damaged.
Smart phone cannot search Bluetooth Rugged Speaker
1. Make sure the Rugged Speaker is in pairing mode ( blue LED
flashing alternately)
2. Delete pairing list in smart phone and searching WIRELESS SPEAKER
again.
3. If it still cannot be found, please restart smart phone and Rugged
Speaker again.
Warning:
Changes or modifications to this unit not espressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device
must accept any interference received,
including interference that may cause undesired operation. Changes or
modifications not expressly
approved by the party responsible for compliance could vold the user’s
authority to operate the equipment.
Previous song
(Conveniently, From now on, when you turn on Rugged speaker it will
automatically search for the last Bluetooth device it was paired with and
reconnected)
2S
2S
2S
X1 1S
Specication