TPL3132 DataSheet TPL3132 BLE 5.0 Module Datasheet Version：V1.
TPL3132 DataSheet TPL3132 BLE 5.0 Module Datasheet 1、Introduction 2、Module Parameters 3、Module Size 4、Pin Definition 5、Reference Design 6、Hardware Design Considerations 6.1、Module placement requirements on the bottom plate 6.2、power supply requirements 6.
TPL3132 DataSheet 1、Introduction TPL3132 is a BLE 5 low power Bluetooth module, which can be widely used in short distance wireless Bluetooth communication. It has the characteristics of small size, low power consumption, strong anti-interference ability and long transmission distance. The other main features of the module are as follows: Built in 512KB flash, 48KB SRAM compliant with Bluetooth 5 standard, which can support various Profile configurations.
TPL3132 DataSheet 3、Module Size 4、Pin Definition 4
TPL3132 DataSheet Number Name PIN Analog Function Remarks 1 MIC_BIAS 2 MIC_P 3 MIC_N 4 RESET 5 PD4/RX Digital I/O SCL0/I2SCLK/PWM4/SSPCLK/URXD0/URXD1/ANTCTL0 /PDMCLK/PWM5/ADC0 6 PD7 Digital I/O SDA1/I2SDIN/PWM1/SSPDIN/UTXD0/UTXD1/ANTCTL1 /PDMDAT/PWM0/ADC3 7 PD6 Digital I/O SCL1/I2SDOUT/PWM0/SSPDOUT/URXD0/URXD1/CLKOUT/PDMCLK/PWM1/ADC2 8 PD5/TX Digital I/O SDA0/I2SFRM/PWM5/SSPCSN/UTXD0/UTXD1/ANTCTL0/PDMDAT/PWM4/ADC1 9 VCC Power 1.8V-4.3V， Recommend 3.
TPL3132 DataSheet 5、Reference Design Explanation: PA2 and PA3 are module downloads and debugger ports. It is recommended that they be pulled out to facilitate debugging and downloading programs. PA4 is connected to the status indicator pin. If the power consumption is not sensitive, it is recommended to pull out a lamp to facilitate the later debugging or maintenance to see if the Bluetooth module is connected. 6、Hardware Design Considerations 6.
TPL3132 DataSheet 6.2、power supply requirements (1) It is recommended to use DC regulator power supply to supply power to the module. The power ripple factor is as small as possible and the module needs to be grounded reliably. Please note that the correct connection between the positive and negative poles of the power supply, such as reverse connection may cause permanent damage to the module.
TPL3132 DataSheet 7、Reflow Profile 8、Packaging As shown below, the package is woven and sealed with an electrostatic bag.
List of applicable FCC rules This device complies with part 15.247 of the FCC Rules. Limited module procedures Not applicable Summarize the specific operational use conditions This module can be applied in remote control toys, sports and fitness sensors , health sensors, mobile accessories as well as smart home. The input voltage to the module should be nominally 1.8-4.3 V DC ，typical value 3.3V DC and the ambient temperature of the module should not exceed 85 ℃.
RF exposure considerations This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment .This equipment should be installed and operated with minimum distance 5mm between the radiator& your body. If the device built into a host as a portable usage， the additional RF exposure evaluation may be required as specified by 2.1093. Antennas This module using PCB antennas with maximum gain is 1.5 dB .
investigation is especially important when integrating multiple modular transmitters where the certification is based on testing each of them in a stand-alone configuration. It is important to note that host product manufacturers should not assume that because the modular transmitter is certified that they do not have any responsibility for final product compliance. c) If the investigation indicates a compliance concern the host product manufacturer is obligated to mitigate the issue.
Frequency spectrum to be investigated For host products with certified modular transmitter， the frequency range of investigation of the composite system is specified by rule in Sections 15.33(a)(1) through (a)(3)， or the range applicable to the digital device， as shown in Section 15.33(b)(1)， whichever is the higher frequency range of investigation. Operating the host product When testing the host product， all the transmitters must be operating.
equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference， and (2) This device must accept any interference received, including interference that may cause undesired operatio. ISED RSS Warning/ISED RF Exposure Statement ISED RSS Warning: This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s).
FCC Statement FCC standards: FCC CFR Title 47 Part 15 Subpart C Section 15.247 PCB antenna , Antenna gain 1.5 dBi This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
—Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
