Instruction Manual - TORBAL AGC Series Laboratory Balances Table of Contents Cautionary Notes and Precautions........................................................................................................................... 3 1. Specification........................................................................................................................................................ 4 2. Keys and Display Indicators..........................................................................
Instruction Manual a Important handling Cautions and Warnings Always handle your scale with care. Damage caused by improper handling is not covered under the scale’s warranty.
Instruction Manual C CAUTIONARY NOTES AND PRECAUTIONS The TORBAL Precision scale is a sensitive and a delicate instrument. Always handle your scale with care. The correct location and proper environment affect the accuracy of your TORBAL Precision Scale. The best location for your scale: 1.Stable, horizontal, vibration-free surface 2.Away from direct sunlight 3.Not exposed to high temperature variations 4.Away from direct drafts 5.
Instruction Manual - TORBAL AGC Series CHAPTER 1. SPECIFICATION Model Capacity AGC100 AGC200 AGC300 AGC500 AGC1000 AGC2000 AGC3000 AGC4000 100g 200g 300g 500g 1000g 2000g 3000g 4000g Readability (d) 0.001 0.01 Repeatability (Standard Divination) 0.001g 0.01g Linearity +/- 0.002g +/- 0.02g Stabilization time (typical) Approx. 3 sec Approx.
Instruction Manual - TORBAL AGC Series KEYS AND DISPLAY INDICATORS Key T (YES) 0 (NO) Menu Primary Function Secondary Function Power On and Power Off - Tare – used to tare the weighing pan Enter and YES (Accept) – used to enter or accept commands Zero – used to zero the scale NO (Reject) – used to reject commands or change values Menu – used to access the main menu Recall – in Totalizing this key is used to recall the Grand Total Add / Start / Lock – In Totalizing (Manual) this key is used to
Instruction Manual - TORBAL AGC Series CHAPTER 3. COMMANDS AND ABBREVIATIONS Command or Abbreviation Description -----CAL TARING LOAD XXX g C CAL FIN AW – X CONT SAPL ON SPL – XX FILL UNDER OVER ACCEPT TARE SAMPLE Taring or re-zeroing in progress READY YES-NO PRINT COUNT FINISH TO START COUNT PRESS C The scale is in the calibration mode. The scale is taring before the calibration process. Place a calibration weight on the pan to begin calibration.
Instruction Manual - TORBAL AGC Series CHAPTER 4.
Instruction Manual - TORBAL AGC Series CHAPTER 5. UNPACKING THE SCALE AND GETTING STARTED 1. Carefully remove the scale, pan, and all of its components from packaging. Place them on a stable base where the scale will not be affected by any mechanical vibrations or air movements. 2. After removing the pan base and the pan from their packaging, carefully install the pan base onto the scale by seating it on the pan support located in the middle of the scale.
Instruction Manual - TORBAL AGC Series 3. Once the pan has been installed, level the scale by adjusting the rear feet until the level indicator shows the “air bubble” is in the center position of the sight glass. The level indicator is located on the rear left side of the scale. 4. After leveling the scale, plug the AC adapter into the AC adapter socket on the rear of the scale. 5.
Instruction Manual - TORBAL AGC Series CHAPTER 6. WEIGHING 1. To begin weighing, press the power button ( ) to turn the scale on. The scale will initialize, perform automatic internal calibration and enter the weighing mode. The scale is ready to begin weighing as soon as the stabilization ( ) and center of zero ( ) indicators appear on the display 2. When weighing, always place the mass in the middle of the pan. The weighed result may be taken when the stabilization indicator appears on the display. 6.
Instruction Manual - TORBAL AGC Series 4. When it has finished re-zeroing, the scale will return to weighing mode and the display will indicate 0.000g. A new center of zero has been set, and the scale is ready for use. 6.1.2.Taring 1. If a container is used for weighing, it may be tared. Taring subtracts the weight of the container from the gross weight to obtain the net weight. 2. To tare the weighing container, place it in the middle of the pan. The container’s weight will be shown on the display. 3.
Instruction Manual - TORBAL AGC Series 6.1.3.Clearing a Tare 1. To clear the tare, remove the tared object along with the net weight from the pan. The scale will then display a negative net tare result. 2. To clear the tare, press the “T” button. 3. The display will show dashed lines indicating the tare is clearing. 4. When it has finished clearing the tare, the scale will return to weighing mode.
Instruction Manual - TORBAL AGC Series CHAPTER 7. MAIN MENU Main Menu is used to configure the scale and its weighing modes. Before entering the menu, complete and clear any active function by pressing the “C” key. To enter the Main Menu press the “MENU” key. Once the “MENU” key is pressed the scale will display available Menu options. Commands: CALIB, UNIT, MODE, AUTO, GLP,PRINT, SET TD and RESET will flash sequentially.
Instruction Manual - TORBAL AGC Series 7.1.1.1.Start (Initializing Automatic Calibration) To calibrate the scale, follow the steps below: 1. Press “MENU” to enter the Main Menu. 2. When CALIB is displayed, press “T” (YES). 3. The scale will display commands Start and Setup sequentially. Press , “T” , when Start is displayed. 4. The scale will display CAL, indicating that the calibration mode has been entered.
Instruction Manual - TORBAL AGC Series 5. Before calibration begins, the scale will perform automatic tare. TARING will be displayed during auto tare. 6. Once the scale tares, command “LOAD C” will be displayed, followed by “C” indicating that automatic calibration is in progress. 7. Calibration can last from 30 to 50 seconds, when it is finished the scale will automatically return to the weighing mode. 7.1.1.2.
Instruction Manual - TORBAL AGC Series 2. When CALIB is displayed, press “T” (YES). 3. The scale will display commands Start and Setup sequentially. Press , “T” , when Setup is displayed. 4. Commands CALIB (Calibration Adjustment), TIME (Time Configuration), and TEMP (Temperature Configuration) will begin to scroll sequentially.
Instruction Manual - TORBAL AGC Series 7.1.1.2.1. Calibration Adjustment The Calibration Adjustment function allows the internal calibration mass value to be adjusted with an external calibration weight that has a traceable class certification. To perform calibration adjustments follow the steps below: 1. Press the “T” (YES) key when “CALIB” is displayed in the calibration setup menu. 2. The scale will display CAL, indicating that the calibration adjustment mode has been entered. 3.
Instruction Manual - TORBAL AGC Series To Change To Accept 5. Command LOAD will be displayed. At any time during the LOAD command, place a single calibration weight in the middle of the pan. 6. Command “C” will be displayed indicating that the scale is recording a new calibration mass value. 7. Once the new calibration value is stored the command “UNLOAD” will be displayed indicating to remove the calibration weight from the pan.
Instruction Manual - TORBAL AGC Series 8. Once the weight is removed the scale will continue with calibration adjustment. CAL will be displayed during the remainder of the adjustment process. Once finished the scale will automatically return to the weighing mode. 7.1.1.2.2.Time Internal calibration can be configured to calibrate automatically within a change of time. To set a calibration time interval, follow the steps below. 1.
Instruction Manual - TORBAL AGC Series 3. A dash will appear on the display indicating to enter a desired time interval. The time interval can be set between 1, 2, 3, 4, 5, and 6 hours (i.e. if set to 3, calibration will be performed once every 3 hours). 4. To set a calibration time interval press the 0 (NO) key until the desired setting is displayed. 5. When the desired setting is displayed press the “Function” key to accept and save the selection. The scale will return to the Calibration Menu.
Instruction Manual - TORBAL AGC Series 1. Press the “T” (YES) key when “TEMP” is displayed in the calibration setup menu. 2. “°C - 0” and the current temperature interval setting will begin to scroll on the display sequentially. To disable temperature interval calibration press the “T” (YES) key when “°C - 0” is displayed. To enable temperature calibration press the “T” (YES) key when the temperature setting is displayed. To Disable To Enable 3. The temperature interval can be set to 0.5°C, 1.0 °C, 1.
Instruction Manual - TORBAL AGC Series 5. When the desired setting is displayed press the “Function” key to accept and save the selection. The scale will return to the Calibration Menu. To exit the Menu, press the C key. 7.1.2. Units of Measure Selection TORBAL AGC series scales can operate in nine different units of measure: grams (g), kilograms (kg), carats (ct), pounds (lb), Newton (n), grains (gn), ounces (oz), ounces troy (oz-t), and pennyweights (dwt).
Instruction Manual - TORBAL AGC Series 2. When command UNIT is displayed press the “T” (Yes) key. 3. The scale will display available units of measure sequentially. When the desired unit is displayed, press the “T” (Yes) key to make the selection. Example (Selecting Ounces) 4. To exit the Main Menu, use the “C” key.
Instruction Manual - TORBAL AGC Series Important: - The symbols for grams (g), kilograms (kg), carats (ct), pounds (lb), and Newton (n) will appear to the right of the measurement on the LCD display. - The symbols for grains (gn), ounces (oz), ounces troy (oz-t), and pennyweight (dwt) are printed on the scale’s panel and an equal sign will point to the symbol indicating the current unit. 7.1.3.Mode configuration TORBAL AGC series scales can operate in seven application modes.
Instruction Manual - TORBAL AGC Series 1. Enter the Main Menu by pressing the “MENU” key. 2. When MODE is displayed press the “T” (YES) key. 3. The application modes will now begin to display sequentially. Press the “T” key when the desired application is displayed and follow the configuration steps for that mode. Note: Scrolling through the options may be accelerated by pressing the 0 (NO) key. (A) Animal Weighing 1. To enable animal weighing, press the “T” (YES) key when ANIMAL is displayed.
Instruction Manual - TORBAL AGC Series 2. Commands An On and An OFF will be displayed sequentially. To enable animal weighing and proceed with configuration press the “T” (YES) key when An On is displayed. If the function is already enabled and you wish to disable it, press the “T” (Yes) key when An OFF is displayed. 3. Animal weighing can operate in three different modes: automatic, semi-automatic and manual (see Table 7.1.3.A). The operating modes will begin to scroll once the function is enabled.
Instruction Manual - TORBAL AGC Series 4. Once the desired operating mode for animal weighing has been selected, the scale will display time intervals for the animal weighing process. The intervals t-3 (3 seconds), t-5 (5 seconds), t-10 (10 seconds), and t-15 (15 seconds) will display sequentially. To select a time interval, press the “T’ (YES) key when the desired time interval is displayed. Note: Select longer time intervals when weighing very active animals.
Instruction Manual - TORBAL AGC Series Table 7.1.3.A: Animal Weighing Operating Modes Automatic Weighing Initialization: Automatic When set to Automatic, the scale will automatically Result Clearing: Automatic begin the animal weighing process. Once the animal Tare: Automatic is removed from the weighing pan, the scale will automatically tare and prepare for the next weighing.
Instruction Manual - TORBAL AGC Series 2. Commands Co On and Co OFF will be displayed sequentially. To enable parts counting and proceed with configuration press the “T” (YES) key when Co On is displayed. If the function is already enabled and you wish to disable it, press the “T” (Yes) key when Co OFF is displayed. 3. After enabling parts counting, select the sample size you want to be used for establishing the average piece weight (APW).
Instruction Manual - TORBAL AGC Series Note: Larger sample size results in a more accurate average piece weight. Select a sample size greater than 10 pieces if a large weight variance might exist between the counted pieces. 4. After selecting the sample size, DONE will be displayed indicating that the function has been configured and it is ready to use. To use the function follow the directions in Chapter 8. To exit the mode menu use the “C” key. (C) Check Weighing 1.
Instruction Manual - TORBAL AGC Series 3. After enabling check weighing, DONE will be displayed indicating that the function has been configured and that the scale is ready for use. To use the function, follow the directions in Chapter 8. To exit the mode menu use the “C” key. (D) Display Hold 1. To enable display hold press the “T” (YES) key when Display is displayed. 2. Commands Di On and Di OFF will be displayed sequentially.
Instruction Manual - TORBAL AGC Series 3. Display hold can operate in three different operating modes: automatic, semi-automatic and manual (see table 7.1.3.D). The operating modes will scroll once the function is enabled. To select a desired operating mode for display hold, press the “T” (YES) key while the mode is displayed. To enable automatic display hold press “T” (YES) while AUTO is displayed. 4.
Instruction Manual - TORBAL AGC Series Table 7.1.3.D: Display Hold Operating Modes When set to Automatic, the scale will automatically Automatic Display Hold initialization: Automatic lock and hold the first stable weight reading on the Result Clearing: Automatic display. When the weight is removed the scale will Tare: Automatic automatically clear the result. Once the result is cleared the scale will automatically tare and prepare for the next weighing.
Instruction Manual - TORBAL AGC Series 2. Commands Pe On and Pe OFF will be displayed sequentially. To enable percent weighing press the “T” (YES) key when Pe On is displayed. If the function is already enabled and you wish to disable it, press the “T” (Yes) key when Pe OFF is displayed. 3. After enabling percent weighing, DONE will be displayed, indicating that the function has been enabled and it is ready to use. To use the function, follow the directions in Chapter 8.
Instruction Manual - TORBAL AGC Series 2. Commands tot On and tot OFF will be displayed sequentially. To enable totalizing and proceed with configuration press the “T” (YES) key when tot On is displayed. If the function is already enabled and you wish to disable it, press the “T” (Yes) key when tot OFF is displayed. 3. The totalizing function can operate in two different operating modes: automatic, and manual (see Table 7.1.3.F). The operating modes will scroll once the function is enabled.
Instruction Manual - TORBAL AGC Series Table 7.1.3.F: Totalizing Operating Modes Automatic Totalizing and Adding: Automatic Manual Totalizing and Adding: Manual When set to Automatic, the scale will automatically add the first stable weight reading to the total. When set to Manual each weigh has to be manually added to the total by pressing a designated key. 7.1.4.Automatic Zero Setting Mechanism (AZSM) All AGC scales are equipped with AZSM, the “Auto Zero Setting Mechanism.
Instruction Manual - TORBAL AGC Series 3. Command AUT On and AUT OFF will flash. 4. To enable AZSM press the “T” (YES) key when AUT On is displayed. To disable AZSM press the “T” (YES) key when AUT OFF is displayed. 5. Once enabled, the AUT indicator will be displayed.
Instruction Manual - TORBAL AGC Series 7.1.5.GLP Print and Data Configuration When enabled, GLP data will appear on every printed transaction receipt. The GLP printout includes Model No., Unit ID, User ID, Project No., Notes / Remarks field, and a Signature field. To enable and configure GLP data printing, follow the steps below: 1. Enter the Main Menu by pressing the “MENU” key.
Instruction Manual - TORBAL AGC Series 2. When command GLP is displayed press the “T” (YES) key. 3. Commands Set, Model, Unit ID, User ID, and Project ID will begin to scroll. 4. To enable or disable GLP press the “T” (YES) key when command SET is displayed. 5. Commands ON and OFF will be displayed. To enable GLP press “T” (YES) when ON is displayed, to disable GLP press “T”(YES) when OFF is displayed.
Instruction Manual - TORBAL AGC Series 6. Once enabled, GLP options will begin to scroll on the display: Model No., Unit ID, User ID, and Project No. 7. Press “T” (YES) when the desired option is displayed. 8. A minus sign will be displayed, indicating you may assign a new ID or project number. Note: ID numbers can consist of up to six digits long.
Instruction Manual - TORBAL AGC Series 9. To enter an ID or a number, use the following keys: 0(NO) to increment a digit, “T” (YES) to accept and go to the next digit, “Function” to accept the entire setting, and “C” to clear and start over. To become familiar with entering an ID, refer to the example in Table 7.1.5.9. To increment and change digits To accept and move to the next digit Table 7.1.5.
Instruction Manual - TORBAL AGC Series 7.1.6.Printing Data and RS232 Communication Port Configurations The printing function is used to print data via the RS232 port. Data may be printed via a printer or sent to a PC via the TORBAL Communication software. 7.1.6.1. Baud and Parity To configure the scale’s RS232 port for printing or to create a PC connection follow the steps below: 1. Enter the Main Menu by pressing the “MENU” key. 2. When Print is displayed press the “T” (YES) key. 3.
Instruction Manual - TORBAL AGC Series 4. To configure the Baud rate settings press the “T” key when Baud is displayed. To configure the Parity setting press “T” key when Parity is displayed. 5. After pressing “T” when Baud is displayed, the scale will display available baud rates: 1200, 2400, 4800, and 9600. To make a selection press “T” (Yes) when the desired setting is displayed.
Instruction Manual - TORBAL AGC Series 6. After pressing “T” when Parity is displayed, the scale will display available parity settings: none, even, odd. 7. To make a selection, press “T” (Yes) when the desired setting is displayed. Note: When connecting the scale to a third-party software or third party printer, make sure that both the host (scale) and the slave are configured with the same Baud and Parity settings.
Instruction Manual - TORBAL AGC Series 7.1.6.2. Torbal Printer Configuration (RXP-4)) To connect the AGC scale to a TORBAL (RXP-4) printer, use the following settings: Scale settings (follow steps detailed in Section 9.1.
Instruction Manual - TORBAL AGC Series 7.1.6.3. Printout Receipts After completing a weighing transaction, result data receipt may be printed. To initiate printing, wait for the weighing result to stabilize and press the “P” key. Note: Examples below include GLP data. For more on GLP printing, turn to Section 7.1.
Instruction Manual - TORBAL AGC Series 7.1.7.Time and Date To set the current time and date, follow the steps below: 1. Enter the Main Menu by pressing the “MENU” key. 2. When SET td is displayed press the “T” (YES) key.
Instruction Manual - TORBAL AGC Series 3. Commands Time and Date will flash. Time: 1. To set the time press the “T” (YES) key when Time is displayed. 2. The current time setting will be displayed. To adjust the time press the 0 (NO) key. 3. A and P will flash. To set AM press the “T” (YES) key when A is displayed, to set PM press the “T” (YES) key when P is displayed. 4. After making the selection, minutes will scroll.
Instruction Manual - TORBAL AGC Series Date: 1. To set the date press “T” (YES) when Date is displayed. 2. The current date setting will be displayed. To change the date, press “T” (YES). 3. The year digit will scroll. Once the desired year is displayed press “T”(YES) to accept and move to the next digit. Follow this sequence until the desired date setting is displayed. After setting the last digit of the month, the date will be automatically saved. 7.1.8.
Instruction Manual - TORBAL AGC Series 2. When RESET is displayed press the “T” (YES) key. 3. The scale will display YES – NO in order to confirm reset initialization. 4. To confirm and initialize the reset function, press the “T” (YES) key. To cancel and abort the reset press the 0 (NO) key. To confirm Master Reset To abort Reset Warning: Resetting the scale will restore the default factory setting. Stored values will be lost and all functions will be disabled.
Instruction Manual - TORBAL AGC Series Table 7.1.5 Factory Default Settings Weighing Function: Always enabled Animal Weighing Function: Disabled Parts Counting Check Weighing Filtering time: t-3 (3 seconds) Function: Disabled Sample Size: 10 pieces Function: Disabled Under Value: 0.000g Over Value: 0.000g Display Hold Function: Disabled Percent Weighing Function: Disabled Totalizing Percent Reference Sample: 0.
Instruction Manual - TORBAL AGC Series CHAPTER 8. FUNCTION MENU: USING THE MODES AND FUNCTIONS All enabled and configured modes as well as applications are ready to use from the Function Menu. To select a function that was enabled and configured follow the steps below: 1. Press the “Function” key. 2. The enabled functions will scroll. Note: Scrolling through the options may be accelerated by manually pressing the 0 (NO) key. 3. When the desired function is displayed, press the “T” (YES) key.
Instruction Manual - TORBAL AGC Series (A) Animal Weighing 1. Before weighing the animal, place an animal weighing container on the scale’s pan and press “T” to tare the scale. 2. Once the scale has been tared, carefully place the animal in the container. Automatic and Semi-Automatic: When set to Automatic or Semi-Automatic, the scale will automatically begin the animal weighing process. Animal weighing will begin with the first weight reading.
Instruction Manual - TORBAL AGC Series Note: In Automatic and Semi-Automatic modes the minimum weighing mass must be equal to or greater than 10d. To see this limit expressed in grams turn to detailed specifications on page 4. Manual: When set to manual, animal weighing must be initialized manually by pressing the “Function” key. 3. Once the animal weighing process is initialized, the scale will count down the time interval that was selected in the configuration mode. The countdown will display.
Instruction Manual - TORBAL AGC Series 4. After the time interval has elapsed the result will be displayed. The animal can now be removed from the pan. Automatic: When set to Automatic, the result will be automatically cleared after the animal is removed. The scale will perform an automatic tare and prepare for the next weighing. If the weighing container is changed the scale must be tared manually by pressing the “T” key.
Instruction Manual - TORBAL AGC Series (B) Parts Counting 1. Place an empty container on the pan and press the “T” key to tare. 2. After taring the container, the scale will display the sample size setting which was configured in the Mode Menu. For example SPL-10 will be displayed, indicating that the current sample size setting is 10 pieces. To accept the sample size press the “T” (YES) key. To change the sample size use the 0 (NO) key.
Instruction Manual - TORBAL AGC Series 3. After confirming the sample size selection, the display will read SAPL On, indicating that you may now place the sample on the pan (10 pieces if SPL-10 is selected). 4. Manually count out the sample and place it in the counting container located on the pan. 5. The weight of the sample will be displayed as it is placed on the pan. Note: Minimum individual piece weight must be equal to or greater than 3e.
Instruction Manual - TORBAL AGC Series 6. Once the weight of the sample stabilizes and the stability indicator appears on the display, press “T” to confirm and accept the sample weight. 7. The display will now indicate to begin filling. The word FILL will flash on the display for approximately 5 seconds. At any time during the FILL command, add the remaining pieces.
Instruction Manual - TORBAL AGC Series 9. Once an accurate piece count has been taken, the container and its contents may be removed from the scale. After the container with the counted pieces has been removed, the scale will indicate the count is finished and that a new count may be initialized by pressing the “C” key. The command “ ---, COUNT FINISH, TO START COUNT PRESS C will appear on the display sequentially. To start a new count press the “C” key.
Instruction Manual - TORBAL AGC Series (C) Check Weighing The check weighing function is used to compare a weight of an object against a preset target range. To set the limits and use the check weighing function follow the steps below. 1. Upon entering the check weighing function, the UNDER limit is displayed. Command UNDER and the under-limit weight setting are displayed sequentially. If this is the first time the function is used, the setting will be 0.000g.
Instruction Manual - TORBAL AGC Series 4. To enter a weight, use the following keys: the 0(NO) key to increment a digit; “T” (YES) to accept and go to the next digit; “P” to insert a decimal; “Function” to accept the entire setting; and “C” to clear and start over . To become familiar with setting the weigh limits, see Table 8.C.4. Table 8.C.4, Example: Setting a weight limit of 20.123g Current Display Action to take Key to use Number of depressions Display becomes 2 20 20.0 20.1 20.10 20.12 20.
Instruction Manual - TORBAL AGC Series 7. To change the OVER limit follow the directions in Step 4 of this section and Table 8.C.4. 8. Once both limits have been set the scale will display a TARE command, indicating that the scale must be tared. Before using the function place a container on the pan and press “T” to tare. 9. The scale is now ready to use. To perform check weighing place your object on the pan to check whether the weight of the object falls within the designated range.
Instruction Manual - TORBAL AGC Series (D) Display Hold The Display Hold function is used to retain a weighing result static on the LCD display after it has stabilized. To use the Display Hold function follow the steps below. 1. Place an empty container on the pan and press “T” to tare. 2. After taring the container, place the weight on the pan.
Instruction Manual - TORBAL AGC Series 3. Weighing Automatic and Semi-Automatic: When set to Auto and Semi-Auto after weight has been added to the pan, the scale will automatically lock the weighing result on the display as soon as it stabilizes. Note: In Automatic and Semi-Automatic modes the minimum weighing mass must be equal to or greater than 10d. To see this limit expressed in grams turn to detailed specifications on page 4.
Instruction Manual - TORBAL AGC Series Semi-Automatic and Manual: When set to Semi-Automatic or Manual, the weighing result will remain displayed and it must be manually cleared after the weight is removed from the pan. To clear the weighing result press the “C” key. After the result has been cleared the scale must be tared. To tare the scale press the “T” key.
Instruction Manual - TORBAL AGC Series 2. Press “T” to tare the scale. 3. Once the scale has been tared, the scale will display the weight of a previously stored sample. If this is the first time the function is used, the sample weight will be 0.000g. To accept the current sample setting, press the “T” (YES) key. To assign a new sample, press the 0(NO) key. To accept To change 4. After pressing the 0 (NO) key command SAPL ON will be displayed.
Instruction Manual - TORBAL AGC Series 5. Place the sample on the pan. The weight of the sample will be displayed. Note: The reference sample must be equal to or greater than 100d. Attempting to set a sample lower than 100d will result in a SAPL LO error. 6. Once the weight of the sample has stabilized and the stability indicator has been displayed, press “T” to accept the sample. Once a new sample weight is set it will be saved until changed or cleared through the master RESET.
Instruction Manual - TORBAL AGC Series 7. After setting the sample weight, the command READY will be displayed. Remove the sample and place the object on the pan. The scale will express the weight of the object as a percentage of the stored sample. Note: To change the percent sample press “C” and repeat Steps 1 to 5. If the same sample weight is used, the scale can be tared without clearing the function and new objects can be weighed.
Instruction Manual - TORBAL AGC Series (F) Totalizing Totalizing is used to add and total weighing results. To use this function, follow the steps below. 1. Place a container on the pan and press “T” to tare. 2. After taking a tare, place the first object on the pan. Automatic When set to Automatic, the weight of the object will be added automatically. Once the weight stabilizes, the TOTAL indicator will appear on the display, signaling that the weight has been added to the grand total.
Instruction Manual - TORBAL AGC Series Manual When set to Manual, the weight of the object must be added manually. Once the weight stabilizes and the stability indicator appears on the display press the “Function” key to add the weight to the grand total. Upon pressing “Function,” TOTAL will appear on the display, signaling the weight has been added to the grand total. Note: With each added weight, the grand total result appears on the display for approximately three seconds.
Instruction Manual - TORBAL AGC Series 4. After the scale has been tared, Steps 1 through 3 can be repeated to add more weighing results to the grand total. 5. To clear the grand total and reset the function press the “C” key. 6. Once “C” has been pressed, the command YES-NO will be displayed, asking to confirm clearing of the function. To abort the clearing the function press the 0 (NO) key. To clear the function press the “T” (YES) key (all data will be lost).
Instruction Manual - TORBAL AGC Series CHAPTER 9.
Instruction Manual - TORBAL AGC Series CHAPTER 10. COMMON ERRORS AND TROUBLESHOOTING Error or Indicator ---- Cause Below zero -- Taring is not allowed - 73 - Re-zeroing is not allowed L Pan error .
Instruction Manual - TORBAL AGC Series CHAPTER 11. MAINTENANCE Cleaning and maintaining your AGC Precision Scale: Before cleaning the scale always unplug the A/C adapter from the electrical outlet. Use a soft, slightly damp cloth to clean the exterior housing of your scale,. Wipe the scale gently. Do not allow any liquid to enter into the scale. Do not apply extensive pressure to the LCD display. Do not use chemicals or benzene when cleaning the surface.
Instruction Manual - TORBAL AGC Series CHAPTER 13. REPLACEMENT PARTS Description A/C Adapter Pan Assembly RS232 Printer Cable Part No. AGC9150 AGC9160 AGC9170 CHAPTER 14. LIMITED WARRANTY PURCHASER’S 24-MONTH WARRANTY Warranty is valid only if the attached warranty registration card is completed and returned within 30 days. This product is a precision device made to exacting standards of scientific accuracy.
