Operating Instructions and Installation Instructions

ManualsBrandsTORK ManualsElectrical15 Amp SunSet Astronomical 2 Grounded Outlets Digital Security Timer

MAINE

MASS

NEW YORK

PENNSYLVANIA

OHIO

IND

ILLINOIS

KENTUCKY

VIRGINIA

NORTH CAROLINATENNESSEE

WEST

VIRGINIA

SOUTH

CAROLINA

GEORGIAALABAMA

MISS

FLORIDA

LOUISIANA

ARKANSAS

OKLAHOMA

MISSOURI

TEXAS

KANSAS

NEW MEXICO

MEXICO

ARIZONA

CALIFORNIA

NEVADA UTAH COLORADO

NEBRASKA

WYOMING

IDAHO

OREGON

SOUTH DAKOTA

IOWA

WISCONSIN

MICHIGAN

MINN

NORTH DAKOTA

MONTANA

WASHINGTON

RHODE ISLAND

CONNECTICUT

NEW JERSEY

MARYLAND

DELAWARE

ASTRONOMIC LATITUDE ZONES

ZONES DE LATITUDE

ZONAS ASTRONOMICAS (LATITUDES)

SUSA

CUSA

NUSA

ALAS

HAWI

PROGRAMMING INSTRUCTIONS

457Z

A DIVISION OF NSi INDUSTRIES, LLC

PLEASE READ ALL INSTRUCTIONS FIRST

ONE YEAR LIMITED WARRANTY: If this product

fails because of a manufacturing defect within

one year after purchase, we will, at our option,

either repair or replace it at no charge. Our

warranty does not cover damage caused by

accident, abuse or misuse. We assume no

further liability with respect to the sale or use

of this product. THIS WARRANTY IS IN LIEU

OF ALL OTHER WARRANTIES, EXPRESSED OR

IMPLIED, INCLUDING THE WARRANTY OF

MERCHANTABILITY. We make no warranty with

respect to the ﬁtness of any goods for the users

particular application. This warranty gives you

speciﬁc legal rights, and you also may have other

rights which vary from state to state.

It is our intent to provide accurate and current

speciﬁcation information. However, in the interest

of product improvement, TORK may alter the

speciﬁcations or constructional details without

prior notice.

SET

MODE

ENTER

1.0 INSTALLATION INSTRUCTION

• Plug the timer into a 120VAC receptacle. If you charge battery

overnight, the unit can be removed and programmed without

AC power.

• Press the R (RESET) button by using an insulated tool.

• Press the ENTER to start the timer.

2.0 SET TIME AND DATE (CALD)

• Press the MODE button two times to display “CALD” ﬂashing.

• Press the ENTER button to start current time setting mode.

• Using buttons change year, then press SET button.

• Continue to using and SET button to enter current month,

date, hour, minutes, and seconds.

• Press the ENTER button to save the current time setting and return

to clock mode.

3.0 SET SCHEDULE

• Press the MODE button to display “PROG” flashing.

• Press the ENTER button to display “PROG 1 ON”. This is the first

of 20 ON/OFF pairs. For first ON program, press SET. To go to other

programs, press .

3.1 SELECT DAYS

• All days are ﬂashing. Use to choose a different set of days,

then press SET.

3.2 SET ON

• Use to choose:

a) “TIME” for a program with user set times

b) “SNUP” for a timer calculated sunrise time that will change daily

throughout the year.

c) “SNST” for a timer calculated sunset time that will change daily

throughout the year.

• Then press SET. If “TIME” selected: Use buttons to change

hour, then press SET button. Repeat for minutes.

3.3 SET OFF

• “PROG 1 OFF” is flashing on display. Press SET.

• All days are flashing. Use to choose a different set of

days, then press SET.

• Use to choose:

a) “TIME” for a program with user set times,

b) “SNUP” for a timer calculated sunrise time that will change daily

throughout the year.

c) “SNST” for a timer calculated sunset time that will change daily

throughout the year.

• Then press SET. If “TIME” selected: Use buttons to change

hour, then press SET button. Repeat for minutes. Press SET.

• Repeat steps for a total 20 ON and 20 OFF time settings.

• Press the ENTER button to finish programming set and return to

clock mode.

4.0 OPTIONAL SUNSET/SUNRISE TIME ZONES

• Press the MODE button three times to display “ZONE” ﬂashing.

• Press the ENTER button to start Zone setting mode.

• Use the keys to display the correct zone.

---

NOTE: NUSA (Default) = North USA, CUSA = Center USA, SUSA = South

USA, ALAS = Alaska&Northern Canada, HAWI = Hawaii&Puerto Rico.

----

• Press the ENTER button to save the setting and return to clock

mode.

5.0 OPTIONAL SUNSET/SUNRISE OFFSET

---

NOTE: This mode displays calculated sunset/sunrise. You can change to

turn ON/OFF earlier or later with this mode.

---

• Press the MODE button four times to display “SUN± ” flashing.

• Press the ENTER button to start offset mode .

• Screen displays today’s SNUP (sun up) time flashing. Use or

to change default time.

• Press SET and screen displays today’s SNST (sunset) time flashing.

Use to change default time.

• Press ENTER to complete the setting and back to normal clock

mode.

6.0 OPTIONAL CHANGE DAYLIGHT SAVINGS TIME (DST)

---

NOTE: Skip this step for default daylight savings dates. Follow instructions

below only if you need to remove or change. MANU (Manual Mode) – no

DST change by timer. NEW mode - change dates to something other than

default dates.

----

• Press the MODE button ﬁve times to display “DST” ﬂashing.

• Press the ENTER button to choose daylight savings times.

• Use the to choose daylight savings options.

a) The display shows “INIT”. For timer to follow current U.S. DST

dates, press ENTER.

b) The display shows “MANU”. For no DST adjustment, press ENTER.

c) The display shows “NEW”. For modiﬁed DST dates, consult

technical support phone line.

7.0 COUNTDOWN TIME SETTING

---

NOTE: Countdown mode will postpone the manual off for a preset period.

As an example, press button to turn off lights and timer will wait ﬁve

minutes before load is shut down. This will give you time to exit the room.

---

• Press the MODE button to display “PROG” ﬂashing.

• Press the ENTER button to display “PROG 1 ON”.

• Press the once to bring the Countdown time setting.

• Press SET for the Countdown (dL) screen.

• Press to choose length of time.

• Press ENTER to complete the setting and back to normal clock

mode.

8.0 RANDOM ON/OFF TIME

• Pressed key SET & simultaneously to set the Random function.

Display shows “RND”.

• To Cancel Random function simply repeat above procedure. The

“RND” sign will disappear from display.

9.0 OVERRIDE BUTTON FUNCTIONS ( )

• Press one time to turn timer ON or OFF.

10.0 ACTIVATE COUNTDOWN

---

NOTE: To activate Countdown step 7 must be completed and the timer in

the ON position.

---

• Press

RATINGS

• 120V 15A, 1800W General Purpose

• 120V 15A, 1800W Resistive

• 120V, 960W Tungsten

• 120V 1/3 HP, TV-5

LI-846

FOR TECHNICAL SUPPORT: SOUTIEN TECHNIQUE : PARA COMUNICARSE CON EL SERVICIO TÉCNICO: techsupport@nsiindustries.com 877.230.7874

http://waterheatertimer.org/Tork-consumer-timers-and-manuals.html

__________________________________________________________________________

Summary of content (2 pages)

PAGE 1
__________________________________________________________________________ http://waterheatertimer.org/Tork-consumer-timers-and-manuals.html PROGRAMMING INSTRUCTIONS 457Z SET MODE ENTER R 4.0 OPTIONAL SUNSET/SUNRISE TIME ZONES • Press the MODE button three times to display “ZONE” flashing. • Press the ENTER button to start Zone setting mode. • Use the keys to display the correct zone. PLEASE READ ALL INSTRUCTIONS FIRST 1.0 INSTALLATION INSTRUCTION • Plug the timer into a 120VAC receptacle.
PAGE 2
VEUILLEZ LIRE TOUTES LES INSTRUCTIONS AVANT D’UTILISER CE PRODUIT PROGRAMMING INSTRUCTIONS 457Z SET MODE ENTER R CARACTÉRISTIQUES • 120 V c.a. 15A, 1800W usage général • 120 V c.a., 15 A, 1800 W résistif • 120 V c.a., 960 W tungstène • 120 V c.a., 1/3 H.P., TV-5 CLASIFICACIONES • 120 VCA 15 A, 1800 VATIOS para uso general • 120 VCA 15 A, 1800 VATIOS resistivo • 120 VCA, 960 VATIOS tungsteno • 120 VCA 1/3 HP, TV-5 1.0 INSTRUCTIONS POUR L’INSTALLATION • Branchez la minuterie sur une prise de 120 V c.a.