Operator's Manual

ManualsBrandsToro ManualsWalk-Behind MowersHoverPro 450 Machine

FormNo.3425-134RevA

HoverPro

450and550Machines

ModelNo.02610—SerialNo.403230000andUp

ModelNo.02611—SerialNo.402000000andUp

Operator'sManual

Introduction

Readthisinformationcarefullytolearnhowtooperate

andmaintainyourproductproperlyandtoavoid

injuryandproductdamage.Youareresponsiblefor

operatingtheproductproperlyandsafely.

YoumaycontactTorodirectlyatwww.Toro.com

forproductsafetyandoperationtrainingmaterials,

accessoryinformation,helpndingadealer,orto

registeryourproduct.

Wheneveryouneedservice,genuineT oroparts,or

additionalinformation,contactanAuthorizedService

DealerorT oroCustomerServiceandhavethemodel

andserialnumbersofyourproductready.Figure1

identiesthelocationofthemodelandserialnumbers

ontheproduct.Writethenumbersinthespace

provided.

g017365

Figure1

1.Modelandserialnumberplate

ModelNo.

SerialNo.

Thismanualidentiespotentialhazardsandhas

safetymessagesidentiedbythesafety-alertsymbol

(Figure2),whichsignalsahazardthatmaycause

seriousinjuryordeathifyoudonotfollowthe

recommendedprecautions.

g000502

Figure2

Safety-alertsymbol

Thismanualuses2wordstohighlightinformation.

Importantcallsattentiontospecialmechanical

informationandNoteemphasizesgeneralinformation

worthyofspecialattention.

ItisaviolationofCaliforniaPublicResourceCode

Section4442or4443touseoroperatetheengineon

anyforest-covered,brush-covered,orgrass-covered

landunlesstheengineisequippedwithaspark

arrester,asdenedinSection4442,maintainedin

effectiveworkingorderortheengineisconstructed,

equipped,andmaintainedforthepreventionofre.

Thismachinedoesnotcomeequippedwitha

sparkarresterstandard.Youmustinstallthe

sparkarresterkitbeforeoperatingthismachinein

California.

Theenclosedengineowner'smanualissupplied

forinformationregardingtheUSEnvironmental

ProtectionAgency(EPA)andtheCaliforniaEmission

ControlRegulationofemissionsystems,maintenance,

andwarranty.Replacementsmaybeorderedthrough

theenginemanufacturer.

Formodelswithstatedenginehorsepower,thegross

horsepoweroftheenginewaslaboratoryratedbythe

enginemanufacturerinaccordancewithSAEJ1349.

Asconguredtomeetsafety,emission,andoperating

requirements,theactualenginehorsepoweronthis

classmachinewillbesignicantlylower.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUK

AllRightsReserved

*3425-134*A

Summary of content (24 pages)

PAGE 1
Form No. 3425-134 Rev A HoverPro® 450 and 550 Machines Model No. 02610—Serial No. 403230000 and Up Model No. 02611—Serial No. 402000000 and Up Operator's Manual Introduction Read this information carefully to learn how to operate and maintain your product properly and to avoid injury and product damage. You are responsible for operating the product properly and safely. You may contact Toro directly at www.Toro.
PAGE 2
Safety WARNING CALIFORNIA Proposition 65 Warning The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. Use of this product may cause exposure to chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. This machine has been designed in accordance with ANSI B71.4-2012. General Safety This product is capable of amputating hands and feet and of throwing objects.
PAGE 3
Safety and Instructional Decals Safety and instructional decals are easily visible and are located near areas of potential danger. Replace any damaged or missing decal. decal130-8322 130-8322 1. Use only fuel with an alcohol content by volume under 10%. 3. Do not use fuel with an alcohol content by volume greater than 10%. 2. Read the Operator's Manual for more information on fuel. decal111-9826 111–9826 1.
PAGE 4
Setup 1 Assembling the Handle No Parts Required decal94-8072 94-8072 1. Warning—cutting/dismemberment hazard of hand or foot, cutting mechanism. Procedure 1. Slide 2 bushings into the frame. g017410 H295159 1. Engine stop (shut off) decal133-8062 133-8062 g017333 Figure 3 1. Lower handle 2. Bushings 4. Frame 5. Bolt 3. Nut 6. Washers 2. 4 Place the lower handle between the bushings and secure it with 1 handlebar bolt, 2 washers, and 1 nut.
PAGE 5
Note: Place the lower handle between the bushings with the kick stop assembly at the right side. 3. Repeat for the opposite side. 4. Align the holes on the upper handle with the lower handle. g209280 Figure 5 1. Nut g209291 Figure 4 1. Upper handle 4. U-bolt 2. Hand wheel 3. Washer 5. Lower handle 5. Fit the U-bolt through the upper and lower handle and secure it with a washer and a hand wheel. 6.
PAGE 6
2 3 Installing the Footstop Filling the Engine with Oil No Parts Required No Parts Required Procedure Procedure Secure the footstop to the bolt on the right side of the lower handle using a nut and 2 washers (Figure 6). Important: Your machine does not come with oil in the engine. Before starting the engine, fill the engine with oil. Note: Install the footstop using the lower hole in the footstop as shown in Figure 6. Engine Oil Specifications Engine oil capacity 0.
PAGE 7
Product Overview g017338 Figure 8 4. Wait 3 minutes for the oil to settle in the engine. 5. Wipe the dipstick clean with a clean cloth. 6. Insert the dipstick into the oil-fill tube, but do not screw it in, then remove the dipstick. 7. Read the oil level on the dipstick (Figure 7). • If the oil level on the dipstick is too low, carefully pour a small amount of oil into the oil-fill tube, wait 3 minutes, and repeat steps 5 through 7 until the oil on the dipstick is at the correct level.
PAGE 8
Fuel Safety Specifications Model Cutting width Product width 02610 46.5 cm (18-1/2 inches) 57.5 cm (22-1/2 inches) 02611 53.5 cm (21 inches) 63.5 cm (25 inches) DANGER Fuel is extremely flammable and highly explosive. A fire or explosion from fuel can burn you and others and can damage property. • To prevent a static charge from igniting the fuel, place the container and/or machine directly on the ground before filling, not in a vehicle or on an object.
PAGE 9
• If the oil level on the dipstick is too low Refer to your engine owner’s manual for additional information. (Figure 12), carefully pour a small amount of multigrade mineral SAE 10W-30 oil with an API series classification of SJ or higher into the oil-fill tube, wait 3 minutes, and repeat steps 3 through 5 until the oil on the dipstick is at the correct level.
PAGE 10
Adjusting the Cutting Height During Operation During Operating Safety WARNING General Safety Adjusting the cutting height may bring you into contact with the moving blade, causing serious injury. • Wear appropriate clothing, including eye protection; long pants; substantial, slip-resistant footwear; and hearing protection. Tie back long hair and do not wear loose clothing or loose jewelry. • Shut off the engine and wait for all moving parts to stop. • Wear gloves while handling the cutting unit.
PAGE 11
Slope Safety • Before operating on any slope, complete a site survey to determine the actual slope where you will operate the machine. • Avoid mowing on wet grass. Poor footing could cause a slip-and-fall accident. • Mow with caution near drop-offs, ditches, or embankments. • When using the machine, always keep both hands on the handle. • When cutting from the top of a steep slope and you need longer reach, use an approved extended handle if you need a longer reach. g017334 Starting the Engine 1.
PAGE 12
Adjusting the Choke Shutting Off the Engine Use the throttle assembly to adjust the choke (Figure 17). Service Interval: Before each use or daily To shut off the engine, release the operator-presence control (Figure 18). Important: When you release the operator-presence control, both the engine and blade should stop within 3 seconds. If they do not stop properly, stop using your machine immediately and contact an Authorized Service Dealer. g017366 Figure 18 g017367 Figure 17 1. Choke on 2.
PAGE 13
Cutting Grass Operating Tips • Cut only about a third of the grass blade at a time. Do not cut below the highest setting unless the grass is sparse or it is late fall when grass growth begins to slow down. Refer to Adjusting the Cutting Height (page 10). General Mowing Tips Important: Operating the machine on slopes of more than 45° will cause severe engine damage due to a lack of lubrication. Do not operate the machine on slopes greater than 45°.
PAGE 14
After Operation After Operating Safety General Safety • Clean grass and debris from the machine to help prevent fires. Clean up oil or fuel spills. • Allow the engine to cool before storing the machine in any enclosure. • Never store the machine or fuel container where there is an open flame, spark, or pilot light, such as on a water heater or on other appliances. Hauling Safety • Use care when loading or unloading the machine. • Secure the machine.
PAGE 15
Maintenance Recommended Maintenance Schedule(s) Maintenance Service Interval Before each use or daily Maintenance Procedure • Ensure that the engine shuts off within 3 seconds after releasing the operator-presence control. • Clean grass clippings and dirt from the entire machine. After each use • Clean grass clippings and dirt from the entire machine. Before storage • Empty the fuel tank before repairs as directed and before annual storage.
PAGE 16
Servicing the Air Filter Preparing for Maintenance Service Interval: Yearly WARNING 1. Tipping the machine may cause the fuel to leak. Fuel is flammable, explosive and can cause personal injury. Press down on the latch tabs on top of the air-filter cover (Figure 20). Run the engine dry or remove the fuel with a hand pump; never siphon. 1. Shut off the engine and wait for all moving parts to stop. 2.
PAGE 17
Changing the Engine Oil oil-fill tube, wait 3 minutes, and repeat steps 8 through 10 until the oil level on the dipstick is correct. Service Interval: Yearly • If the oil level on the dipstick is too high, Note: Run the engine a few minutes before changing drain the excess oil until the oil level on the dipstick is correct. the oil to warm it. Warm oil flows better and carries more contaminants. Important: If the oil level in the engine is too Engine Oil Specifications Engine oil capacity 0.
PAGE 18
Replacing the Blade the ratchet or wrench and tighten the bolt securely. This bolt is very difficult to overtighten. Service Interval: Yearly Important: You will need a torque wrench to install the blade properly. If you do not have a torque wrench or are uncomfortable performing this procedure, contact an Authorized Service Dealer. Examine the blade whenever you run out of fuel. If the blade is damaged or cracked, replace it immediately.
PAGE 19
Storage Store the machine in a cool, clean, dry place. Preparing the Machine for Storage WARNING Fuel vapors can explode. • Do not store fuel more than 30 days. • Do not store the machine in an enclosure near an open flame. • Allow the engine to cool before storing it. 1. On the last refueling of the year, add fuel stabilizer to the fuel as directed by the engine manufacturer. 2. Run the machine until the engine shuts off from running out of fuel. 3. Prime the engine and start it again. 4.
PAGE 20
Troubleshooting Problem The engine does not start. Possible Cause 1. The wire is not connected to the spark plug. 1. Connect the wire to the spark plug. 2. The hole in the fuel-cap vent is plugged. 3. The spark plug is pitted, fouled, or the gap is incorrect. 2. Clean the hole in the fuel-cap vent or replace the fuel cap. 3. Check the spark plug and adjust the gap if necessary. Replace the spark plug if it is pitted, fouled, or cracked. 4. Drain and/or fill the fuel tank with fresh fuel.
PAGE 21
Notes:
PAGE 22
Notes:
PAGE 23
California Proposition 65 Warning Information What is this warning? You may see a product for sale that has a warning label like the following: WARNING: Cancer and Reproductive Harm—www.p65Warnings.ca.gov. What is Prop 65? Prop 65 applies to any company operating in California, selling products in California, or manufacturing products that may be sold in or brought into California.
PAGE 24
The Toro Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).