Setup Instructions

ManualsBrandsToro ManualsWalk-Behind Mowers36RD Mid-Size Rear-Discharge Deck

FormNo.3405-967RevB

32RDMid-SizeRear-DischargeDeck

ModelNo.02710—SerialNo.316000001andUp

ModelNo.02711—SerialNo.316000001andUp

ModelNo.02712—SerialNo.316000001andUp

SetupInstructions

Theseinstructionsarefordealersonly.

Theseinstructionsareforadealertoinstallacutting

deck(Models02710,02711,or02712)toaMid-Size

PowerUnit(Models30069and31914).

WARNING

Performingmaintenancewhiletheengineis

runningcanexposeyourhands,otherparts

ofyourbody,andclothingtogetcaughtin

movingparts,causingseriousinjury.

Ifyoumustperformanymaintenancewhile

theengineisrunning,keepyourhands,feet,

clothing,andpartsofyourbodyawayfrom

thecuttingunitandmovingparts.

WARNING

Engineexhaustcontainscarbonmonoxide,

whichisanodorless,deadlypoisonthatcan

killyou.

Donotrunengineindoorsorinanenclosed

area.

Important:Readandunderstandtheseassembly

instructionsbeforeproceeding.RefertotheParts

CatalogandOperator'sManualforthemachineto

determinewhichofthesepartsaretobetted.

Important:Ensurethatallliftingequipmentis

ingoodconditionandhasasafeandadequate

capacity.Alwaysseekassistancewhenlifting

awkwardorheavyloads.

Important:Torqueallfastenerstothespecied

torquesettings.Thepartsbeingttedmustnotbe

drilled,cutoralteredinanyway.

PreparingtheMachine

NoPartsRequired

Procedure

1.Parkthemachineonalevelsurfaceandengage

theparkingbrake.

2.Shutofftheengine,removethekey,andwait

fortheenginetocool.

3.Raiseandsupportthetractionunit.

4.Removethe4lugnutssecuringbothwheelsto

thetractionunit(Figure1).

g237244

Figure1

Leftsideshown

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

AllRightsReserved

*3405-967*B

Summary of content (8 pages)

PAGE 1
Form No. 3405-967 Rev B 32RD Mid-Size Rear-Discharge Deck Model No. 02710—Serial No. 316000001 and Up Model No. 02711—Serial No. 316000001 and Up Model No. 02712—Serial No. 316000001 and Up Setup Instructions These instructions are for dealers only. These instructions are for a dealer to install a cutting deck (Models 02710, 02711, or 02712) to a Mid-Size Power Unit (Models 30069 and 31914).
PAGE 2
5. Remove the wheels (Figure 1). 6. Remove the deck cover and the PTO engagement linkage rod before lifting and moving the rotary cutting deck into position against the power unit (Figure 2). 2 Installing the Cutting Deck Parts needed for this procedure: 8 Bolt (3/8 x 1 inch) 8 Curved washer 8 Flange nut (3/8 inch) Procedure 1. Install 8 bolts (3/8 x 1 inch), curved washers, and flange nuts to secure the rotary cutting deck to the power unit as shown in Figure 3.
PAGE 3
Installing the Guards Parts needed for this procedure: g237288 Figure 4 1. Bell-crank yoke 4. 5. 6. 2. PTO engagement linkage Adjust the PTO engagement as directed in the Adjusting the Mower Belt Tension section in the traction unit Operator’s Manual. Check the adjustment of the PTO safety switch as directed in the Adjusting the Mower Belt Tension section in the traction unit Operator’s Manual.
PAGE 4
B. Install the guard to the traction unit using 2 bolts (M8 x 25 mm), 4 washers (M8–17), and 2 locknuts (M8) in the lower hole on the engine frame (Figure 6). C. Secure the front of the guard to the deck using the center bolt, washer, and nut you removed previously (Figure 6). 2. Refer to the Adjusting the Height of Cut section in the Operator's Manual and check the height setting of the rear axle depending on what height of cut is required. 3.
PAGE 5
3. Turn the high idle screw so that the end of it just touches the speed control lever, and tighten the lock nut (Figure 9). 4. Check the high idle speed and repeat this procedure if necessary. 5. Loosen the cable screw and adjust the cable length so that the throttle lever on the operator control panel is set to full throttle when the speed control lever touches the previously set high idle screw. 6. Tighten the cable screw.
PAGE 6
Notes:
PAGE 7
Notes:
PAGE 8