Setup Instructions

ManualsBrandsToro ManualsWalk-Behind Mowers36RD Mid-Size Rear-Discharge Deck

FormNo.3367-846RevC

32RD,36RD,and48RDMid-SizeRear-Discharge

Deck

ModelNo.02710—SerialNo.312000001andUp

ModelNo.02711—SerialNo.312000001andUp

ModelNo.02712—SerialNo.312000001andUp

SetupInstructions

Theseinstructionsmustnotbesuppliedtothecustomer.

Theseinstructionscovertheprocedureforadealerto

installacuttingdeck(02710,02711,or02712)toaMid

SizePowerUnit(30069).

Thisequipmenthasbeendesignedandconstructedso

that,insofarasisreasonablypractical,theymeetthe

safetyrequirementsofEuropeanstandardEN836and

theywillnotendangerthehealthandsafetyofthose

workingwiththem.Thisis,however,subjecttothe

machinebeingproperlymaintainedandusedaccording

totheconditionsstatedintheOperator'sManual,and

elsewhere,whichhavebeenfoundnecessaryasaresult

oftheresearchandtestingoftheTorocompany.

WARNING

Iftheengineneedstoberunningtoperform

anymaintenanceadjustments,keephands,feet,

clothing,andpartsofthebodyawayfromthe

cuttingunitandmovingparts.

WARNING

Engineexhaustcontainscarbonmonoxide,which

isanodorless,deadlypoisonthatcankillyou.

Donotrunengineindoorsorinanenclosedarea.

Important:Readandunderstandtheseassembly

instructionsbeforeproceeding.Refertothe

P ar ts

Catalo g

and

Operator's Man ual

forthemachineto

whichthesepartsaretobetted.

Important:Ensurethatallliftingequipmentis

ingoodconditionandhasasafeandadequate

capacity.Alwaysseekassistancewhenlifting

awkwardorheavyloads.

Important:Torqueallfastenerstothespecied

torquesettings.Thepartsbeingttedmustnotbe

drilled,cutoralteredinanyway.

InstallingtheCuttingDeck

Partsneededforthisprocedure:

Centerdischargeguard

Carriagebolt(M10x25mm)

Washer(M8–17)

Locknut(M8)

Flangenut(3/8inch)

1Undersideguard

Bolt(M8x25mm)

1Drivepulleyguard

Bolt(3/8x1inch)

Heavywasher(M10)

Nut(M10)

Curvedwasher

1Dragshield

Springwasher(M10)

Procedure

1.Raiseandsupportthetractionunitusingasuitable

liftingmethod.

2.Removebothwheelsfromthetractionunit

(Figure1).

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

AllRightsReserved

Summary of content (4 pages)

PAGE 1
Form No. 3367-846 Rev C 32RD, 36RD, and 48RD Mid-Size Rear-Discharge Deck Model No. 02710—Serial No. 312000001 and Up Model No. 02711—Serial No. 312000001 and Up Model No. 02712—Serial No. 312000001 and Up Setup Instructions These instructions must not be supplied to the customer. These instructions cover the procedure for a dealer to install a cutting deck (02710, 02711, or 02712) to a Mid Size Power Unit (30069).
PAGE 2
Figure 3 Figure 1 1. Flange nut (3/8 inch) 3. Bolt (3/8 x 1 inch) 2. Curved washer 3. Remove the deck cover and the PTO engagement linkage rod before lifting and manoeuvring the rotary cutting deck into position against the power unit (Figure 2). Note: Figure 3 shows the fasteners out side of the mowing unit to better illustrate which configuration goes with each hole. Install the bolts and washers together on the same side of the frame. 5. Torque the bolts to 40 to 47 N-m. 6.
PAGE 3
setting of the rear axle depending on what height of cut is required. 13. Install the traction wheels to the hubs and secure with drive wheel lug nuts. Torque Nuts to 122 - 129 N-m. 14. Lower the unit to the ground. 15. Install the drive pulley guard to the rear of the engine frame with 2 carriage bolts (M10 x 25 mm), heavy washers (M10), spring washers, and nuts (M10)(Figure 7). Ensure that you center the guard on the engine frame. the belt guide under the engine frame and adjust the belt guide.
PAGE 4
1 captured in the lanyards on the drive pulley guard (Figure 8). 18. Adjust the caster position and the blade height to the correct height of cut referring to the Adjusting the Height of Cut section in the Operator’s Manual. Install the deck cover and secure it with the removed fasteners. 2 19. If the hydraulic pump by-pass valve was opened so the power unit could be pushed, close the by-pass valves, but do not over tighten.