Installation Instructions

ManualsBrandsToro ManualsAttachmentsFloating 200mm (8in) Cutting Unit, 5-Plex Mower

FormNo.3412-332RevA

Floating200mm(8in)CuttingUnit

5-PlexMower

ModelNo.02821

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

Introduction

Readthisinformationcarefullytolearnhowtooperateand

maintainyourproductproperlyandtoavoidinjuryand

productdamage.Youareresponsibleforoperatingthe

productproperlyandsafely.

YoumaycontactTorodirectlyatwww .Toro.comforproduct

safetyandoperationtrainingmaterials,accessoryinformation,

helpndingadealer,ortoregisteryourproduct.

Wheneveryouneedservice,genuineToroparts,oradditional

information,contactanAuthorizedToroDistributoror

ToroCustomerServiceandhavethemodelnumberofyour

productready.

ThisproductcomplieswithallrelevantEuropeandirectives.

Fordetails,pleaseseetheDeclarationofIncorporation(DOI)

atthebackofthispublication.

Contents

Introduction..................................................................1

Setup............................................................................1

PreparingtheMachine.............................................2

PreparingtheCuttingUnits......................................2

InstallingtheKit.....................................................3

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

Description

Qty.

Use

Nut(16mm)

Washer(16mm)

Pin(8mm)

Greasetting

Washer(10mm)

Hexnut(10mm)

Pin(25mm)

Splitpin

Float-castingpivot

Bushing(30x20mm)

Bushing(25x25mm)

Carriagebolt(M10x8.8mm)

Roller2

Rightwing-headstop1

Leftwing-headstop

Bolt(M16x120mm)

Installthekit.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3412-332*A

Summary of content (4 pages)

PAGE 1
Form No. 3412-332 Rev A Floating 200 mm (8in) Cutting Unit 5-Plex Mower Model No. 02821 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Introduction This product complies with all relevant European directives. For details, please see the Declaration of Incorporation (DOI) at the back of this publication.
PAGE 2
Preparing the Machine 1. Park the machine on a level surface. 2. Lower the cutting units. 3. Engage the parking brake. 4. Shut off the engine and remove the key from the key switch. g196985 Figure 1 Preparing the Cutting Units 1. Release the cutting unit from the arm by removing the locknut (24 mm) and plain washer from the cutting unit pivot pin. Refer to the relevant machine Operator’s Manual. g196882 Figure 2 2. Remove the cutting unit from the pin.
PAGE 3
Installing the Kit g199808 Figure 3 9. Float-casting pivot 1. Nut (16 mm) 2. Washer (16 mm) 10. Bushing (30 x 20 mm) 3. Pin (8 mm) 11. Bushing (25 x 25 mm) 4. Grease fitting 12. Carriage bolt (M10 x 8.8 mm) 5. Washer (10 mm) 13. Roller 6. Hex nut (10 mm) 14. Right wing-head stop 7. Pin (25 mm) 15. Left wing-head stop 8. Split pin 16. Bolt (M16 x 120 mm) Note: The instructions below refer to the conversion of the cutting unit from a fixed configuration to a floating configuration.
PAGE 4
Declaration of Incorporation The Toro Company, 8111 Lyndale Ave. South, Bloomington, MN, USA declares that the following unit(s) conform(s) to the directives listed, when installed in accordance with the accompanying instructions onto certain Toro models as indicated on the relevant Declarations of Conformity. Model No. 02821 Serial No.