Form No. 3394-155 Rev A Mauser KS-534 Full Safety Cab CT2240/LT3340 and Groundsmaster® 3400 Mowers Model No. 02890—Serial No. 315000001 and Up Register at www.Toro.com.
This product complies with all relevant European directives. For details, please see the Declaration of Incorporation (DOI) at the back of this publication. Figure 2 1. Safety alert symbol Introduction This manual uses 2 words to highlight information. Important calls attention to special mechanical information and Note emphasizes general information worthy of special attention. This manual provides instructions for the operation and operator maintenance of the Full Safety Cab.
Maximum Slope Angles of Mowers with Cab Safety WARNING This cab can be fitted to the mowers listed at the front of this document. When fitted with a cab, each mower model has a different maximum slope angle and this is stated on the decal located on the lid of the storage pod on the left of the machine. Refer to Safety and Instructional Decals (page 4) for the correct maximum slope angle decal for your machine when fitted with a cab.
Sound Pressure Level Sound pressure level was determined according to the procedures outlined in EN ISO 5395. Model CT2240 Model GM3400 These units have a sound pressure level at the operator’s ear of 83 dBA, which includes an Uncertainty Value (K) of 2 dBA. This unit has a sound pressure level at the operator’s ear of 86 dBA, which includes an Uncertainty Value (K) of2 dBA. Sound pressure level was determined according to the procedures outlined in EN ISO 5395.
111-8164 Groundsmaster 3400 (Model 30651) 3. Warning—always wear a seatbelt. 1. Tipping hazard—always perform slow turns; go slowly up inclines. 2. Tipping hazard—do not drive up slopes greater that 15 degrees. 4. Warning—read the Operator's Manual; remove the key from the ignition before performing maintenance; thrown object hazard; keep bystanders away from the machine.
111-8165 CT2240 (Model 30654) 3. Warning—always wear a seatbelt. 1. Tipping hazard—always perform slow turns; go slowly up inclines. 2. Tipping hazard—do not drive up slopes greater that 17 degrees. 4. Warning—read the Operator's Manual; remove the key from the ignition before performing maintenance; thrown object hazard; keep bystanders away from the machine.
111-8237 LT3340 (Model 30657) 3. Warning—always wear a seatbelt. 1. Tipping hazard—always perform slow turns; go slowly up inclines. 2. Tipping hazard—do not drive up slopes greater that 18 degrees. 4. Warning—read the Operator's Manual; remove the key from the ignition before performing maintenance; thrown object hazard; keep bystanders away from the machine.
Product Overview Controls Heater/Blower Controls The controls are mounted on the right side in the roof lining. Figure 5 2 1. Interior light switch 1 Front Widow Handle (2) The front window can be opened for ventilation. There are two handles (Figure 6). 1 g020347 Figure 3 1. Blower speed switch 3. Air conditioner switch (Air Conditioning Optional) 2. Temperature controller g018406 Figure 6 Screen Wiper and Washer Switch 1.
Operation WARNING If you operate your machine in temperatures below 5 degrees C (40 degrees F), use washer fluid with antifreeze protection. Failure to use washer fluid with antifreeze protection in cold weather could result in impaired windscreen vision and increase the risk of injury or accident. Note: Determine the left and right sides of the machine from the normal operating position. Operating the Heating System 1. Set the air conditioner switch to Off. 2.
To open the door from inside the cab, pull back on the door lock release lever while opening the door (Figure 10). Figure 10 1. Door lock 2. Release lever Adjusting the Mirrors While the sitting in the seat, have a helper adjust the side view mirrors to attain the best view around the side of the machine (Figure 11). 1 g020380 Figure 11 1.
Maintenance 4. Once the cab has been fully raised, install the safety support bracket as follows: • Remove the safety support bracket from the WARNING storage pod. Working on the machine without the safety support bracket increases your risk of injury. • Using either of the 2 cross beam brackets, place the safety support bracket within the cross beam brackets and insert the appropriate locking lever through both brackets and rotate downwards.
Figure 14 1. Cab fuse block Washing the Machine and Cab When washing the machine and the cab, do not direct water into the roof area.
Notes: 13
Declaration of Incorporation The Toro Company, 8111 Lyndale Ave. South, Bloomington, MN, USA declares that the following unit(s) conform(s) to the directives listed, when installed in accordance with the accompanying instructions onto certain Toro models as indicated on the relevant Declarations of Conformity. Model No. 02890 Serial No.
International Distributor List Distributor: Country: Phone Number: Distributor: Phone Number: 57 1 236 4079 Colombia Japan 81 3 3252 2285 Czech Republic 420 255 704 220 420 255 704 Slovakia 220 Argentina 54 11 4 821 9999 Russia 7 495 411 61 20 Ecuador 593 4 239 6970 Finland 358 987 00733 Agrolanc Kft Balama Prima Engineering Equip. B-Ray Corporation Hungary Hong Kong Korea 36 27 539 640 852 2155 2163 82 32 551 2076 Maquiver S.A. Maruyama Mfg. Co. Inc. Mountfield a.s.
The Toro Total Coverage Guarantee A Limited Warranty Conditions and Products Covered The Toro® Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
