Installation Instructions

ManualsBrandsToro ManualsAttachments12V Electrical Accessory Port Kit, CT Series Turf Mowers or Groundsmaster 3400 Traction Unit

FormNo.3423-981RevB

12VElectricalAccessoryPortKit

CTSeriesTurfMowersorGroundsmaster

3400TractionUnit

ModelNo.02902

InstallationInstructions

Introduction

Thiskitprovidesa12VpoweroutletforaMP3player,mobiledevice,2-wayradio,orsimilarlow-powerdevice.

UsethiskitontheCTseriesandGM3400machines.

WARNING

CALIFORNIA

Proposition65Warning

UseofthisproductmaycauseexposuretochemicalsknowntotheStateofCalifornia

tocausecancer,birthdefects,orotherreproductiveharm.

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Nopartsrequired

–

Disconnectthebattery.

Nopartsrequired

–

Openthecontrolconsole.

Accessory-portbracket1

Accessoryport1

Countersunk-headscrews(3x20mm)

Installtheaccessoryport.

Nopartsrequired

–

Installthefuse(15A).

Nopartsrequired

–

Connectthenegativebatterycable.

Seriallabel

Completetheaccessoryportinstallation.

Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3423-981*B

Summary of content (8 pages)

PAGE 1
Form No. 3423-981 Rev B 12V Electrical Accessory Port Kit CT Series Turf Mowers or Groundsmaster® 3400 Traction Unit Model No. 02902 Installation Instructions Introduction This kit provides a 12V power outlet for a MP3 player, mobile device, 2-way radio, or similar low-power device. Use this kit on the CT series and GM3400 machines.
PAGE 2
1 3 Preparing the Machine Accessing the Console No Parts Required No Parts Required Procedure Procedure 1. Park the machine on a level surface. 1. 2. Shut off the cutting units. 3. Lower the cutting units. 4. Engage the parking brake, shut off the engine, remove the key, and wait for all movement to stop before leaving the operator’s seat. Remove the 6 screws and 6 washers that secure the control panel to the console (Figure 2). 2 Disconnecting the Battery No Parts Required Procedure 1.
PAGE 3
4 Installing the Accessory Port Parts needed for this procedure: g274354 Figure 5 1 Accessory-port bracket 1 Accessory port 1. (+) spade connector 4. (-) spade connector 3 Countersunk-head screws (3 x 20 mm) 2. Socket-terminal connector (white/red wire) 5. Socket-terminal connector (black wire) 3. Accessory port Procedure 1. Cut a hole in the decal at the rear of the console arm (Figure 3). 4.
PAGE 4
5 6 Installing the Fuse Connecting the Negative Battery Cable No Parts Required No Parts Required Procedure 1. Remove the cover from the fuse block (Figure 7). Procedure 1. Assemble the negative battery cable onto the negative battery post (Figure 9). g274376 Figure 9 g037069 Figure 7 1. Cover (fuse block) 2. 2. Align the insulator cover of the battery-cable terminal and close the cover (Figure 9). Insert the fuse (15 A) into the 2nd slot from the left side of the fuse block (Figure 8).
PAGE 5
g274526 Figure 11 1. Serial decal (machine) 2. Serial decal (accessory-port kit) 2. Remove the backing from the serial decal from the accessory-port kit. 3. Affix the serial decal to the surface adjacent to the serial plate for the machine (Figure 11). Operation The 12 VDC socket is permanently powered through the fuse (15 A). g274375 Figure 10 1. Console 2. Control panel 2. Connecting Low-Power Device to the Accessory Port 3.
PAGE 6
Disconnecting Low-Power Device from the Accessory Port 1. Remove the power cord of the 12 VDC device from the accessory port. 2. Install the protective rubber cap onto the port; refer to Figure 12 in Connecting Low-Power Device to the Accessory Port (page 5). Maintenance Maintaining the Accessory Port Service Interval: Monthly • Check the socket for moisture and dirt. – Dry and clean the socket as needed. – Check the condition of the rubber cap.
PAGE 7
EEA/UK Privacy Notice Toro’s Use of Your Personal Information The Toro Company (“Toro”) respects your privacy. When you purchase our products, we may collect certain personal information about you, either directly from you or through your local Toro company or dealer.
PAGE 8