Form No. 3433-706 Rev B Road Light Kit including Brake Lights LT-F3000 Series Traction Unit Model No. 02918—Serial No. 401330001 and Up Installation Instructions This product complies with all relevant European directives. For details, please see the Declaration of Incorporation (DOI) at the back of this publication. Installation Loose Parts Use the chart below to verify that all parts have been shipped.
Procedure 5 6 Description Use Qty. Light switch Hazard switch Direction-indicator switch Connector lead Adhesive reflector Cable tie Serial number label 1 1 1 1 2 20 1 Install the switches. Complete the installation. 1 Preparing the Machine No Parts Required Procedure 1. Park the machine on a level surface, engage the parking brake, lower all cutting units, shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operator’s seat. 2. Open the hood. 3.
4. 2 Assemble the existing washer and new locknut (16 mm) onto the bolt, and torque the nut to 15 N∙m (11 ft-lb). Note: Do not overtighten the locknut; doing so Installing the ROPS Area Components makes the roll bar difficult to lower.
g028922 Figure 3 View on cable entry g295696 Figure 5 1. Connector lead 5. Number plate connector 2. Black and red connector 6. Indicator light connector 1. Relay socket 2. Relay 3. Black and green connector 7. Stop/taillight connector 4. Black, red, and orange connector 8. Installing the Number Plate and Plate Light Repeat steps 2 through 7 at the right side of the machine. WARNING When drilling or carrying out other operations, always wear eye protection.
g035919 Figure 7 g028931 1. Number-plate bracket 3. Hex-head screw (6 x 35 mm) Figure 9 1. Socket-head screw (3 x 16 3. Number plate light mm) 2. Washer (1/4 x 7/8 inch) 2. Washer (3 mm) 4. Assemble the number plate to the number plate bracket using 2 hex-head screws (6 x 20 mm), 4 washers (6 mm), and 2 locknuts (6 mm) as shown in Figure 8. 6. 4. Locknut (3 mm) Insert the red wire terminal and the black wire terminal into the connector shell as shown in Figure 10. g293577 Figure 10 1.
3 Installing the Brake-Pressure Switch Parts needed for this procedure: 1 Pressure-switch connector 1 Pressure switch g295754 Assembling the Brake Pressure Switch Connector 1. Figure 12 At the right side of the transmission manifold, remove the 2 cable ties that secure the branch of the machine wire harness for the brake pressure switch (Figure 11). 1. Wire harness branch 3. Compression nut 2. Shell (pressure-switch connector) 4. Connector body 4.
g293533 g293532 Figure 14 g295755 Figure 13 1. Pin–1 hole 5. Green/yellow wire 2. Pin–2 hole (not used) 6. Blue wire 3. Pin–3 hole 7. Connector body 4. Pin–4 hole 8. Brown wire 1. Port PS (transmission manifold) 3. Plug 2. Seal 4. Back of the machine 2. Note: Discard the plug and seal. 3. 6. Secure the wires with the terminal screw in the connector body. 7. Assemble the connector body and the compression nut to the shell. Remove the plug and seal (Figure 14).
4. Install the pressure-switch connector onto the electrical connector of the pressure switch (Figure 16). g293531 Figure 16 1. Pressure switch g234606 Figure 17 2. Pressure-switch connector 4 1. Use this hole (right light support). 3. Existing hole 2. Use this hole (left light support). 4. Drill a (9 mm) hole here. 2. Installing the Front Lights Install the left and right light supports to the machine with 4 bolt (8 x 35 mm), 8 washers (8 mm), and 4 locknuts (8 mm) as shown in Figure 18.
g235647 Figure 19 1. Locknut (8 mm) 4. Hex-head screws (8 x 25 mm) 2. Washer (8 mm) 5. Front light bracket assembly 3. Washer (5/16 inch) 4. Remove the nut and washer from each light and use them to install the lights to the front light bracket (Figure 20). g235648 Figure 20 1. Nut 3. Light 2. Washer Connecting the Wires 1.
2. Plug the headlamp into the connector. 3. Insert the red wire terminal and the black wire terminal into the connector shell as shown in Figure 22. g028967 Figure 24 Front light harness 1. Front marker light — black wire (top), red/white wire (bottom) 3. Headlamp — black wire (top), blue wire (bottom) 2. Front indicator light — black wire (top), green wire (bottom) g293577 Figure 22 1. Connector shell 2. Black wire 3. Red wire 4.
5. At the rear face of the control console above the key switch, remove the switch blank panels between the auto limited lift and beacon switches (Figure 27). g028968 Figure 25 g028971 1. Screw 2. Control panel 2. 3. Figure 27 3. Control console 1. Auto limited lift switch 2. Lights switch Carefully lift off the panel, ensuring that the connectors to the existing switches are not separated. Feed the longest end of the connector lead down the control arm (Figure 26). 3. Hazard switch 4.
6 Completing the Installation Parts needed for this procedure: 2 Adhesive reflector 20 Cable tie 1 Serial number label Procedure 1. Secure the wire harnesses for the front lights, rear lights, and the pressure switch to the chassis with cable ties to prevent the harnesses from becoming trapped or chafed. 2. Connect the negative cable to the battery. 3.
Brake Lights Operation The brake lights automatically turn on when the machine is decelerating (when the control pedal is returning to neutral, when travelling in a forward direction only). Position the marker lights (front and rear). Press the top of the switch—the switch will illuminate and the red (rear) and white (front) marker lights will turn on. Adjusting the Headlights Maintenance Adjust the headlights so that the horizontal part of the cut-off of the beam is tilted downward at 2.0%. 1.
Declaration of Incorporation The Toro Company, 8111 Lyndale Ave. South, Bloomington, MN, USA declares that the following unit(s) conform(s) to the directives listed, when installed in accordance with the accompanying instructions onto certain Toro models as indicated on the relevant Declarations of Conformity. Model No. 02918 Serial No.
European Privacy Notice The Information Toro Collects Toro Warranty Company (Toro) respects your privacy. In order to process your warranty claim and contact you in the event of a product recall, we ask you to share certain personal information with us, either directly or through your local Toro company or dealer. The Toro warranty system is hosted on servers located within the United States where privacy law may not provide the same protection as applies in your country.
The Toro Warranty Two-Year or 1,500 Hours Limited Warranty Conditions and Products Covered Parts The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for 2 years or 1,500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).