-~ ...to the TOR Owner This Owner Manual has been especially prepared for your information and guidance in the operation and care of your new Toto mower. Properly adjusted, operated and maintained, this Toto mower will respond quickly and easily to every reasonable demand and give years of reliable service. Toto mowers are manufactured by an organization of winnowing machinery specialists for over titty years. Each machine is carefully inspected and tested before leaving the factory.
KNOW YOUR MOWER 7 REEL DRIVE LEVER TRACTION DRIVE LEVER AIR CLEANER THROTTLE OlL LEVEL OlL Fill OlL DRAIN ' HEIGHT OF cur ADJUSTMENT REEL ADJUSTMENT OPERATING and SAFETY INSTRUCTIONS BEFORE STARTING 1. Thoroughly inspect the area where the equipment is to be used and remove al} stones, wire, bones, pieces of metal and other foreign objects. 2. Wipe up any gasoline spilled, and avoid spilling on hot engine. 3. Know how to $top equipment and engine quickly, DURING OPERATIONS 4.
LUBRICATION 3. Perk fitting use good grade of gun grease every eight hours of operation, There are seven zero fittings in all, NOTE: This zero tilting is located behind and in the center of the main {mare (see inset) and can be serviced by (silting the mower forward. * Four inch black required under wheel, 2. Linkage « apply a lew drops of a good grade of lubricating oil every eight hours of operation. 3. Engine use a good grade of SAE 30 engine oil. {Capacity 15 1] pints).
OPERATION The front cutting units are put into transport position or returned to mowing position by pressing transport lever "E' while lifting on reel guard "F, TIRE INFORMATION Tire pressure should be maintained at 12 pounds, Electric start model of this mower utilizes calcium chloride in the sulky tire as a counter-balance. CAUTION: DO NOT CHECK TIRE PRESSURE ON THE GRASS, ROTATE VALVE STEM TO TOP WHEN CHECKING TIRE PRESSURE.
L9 OPERATION With the 38" Professional on i level surface, remove the ail filler cap, (see photo above. | Fill crankcase to Lie full mark (Ion the dipstick. Fill engine to proper revel want Carefully foil the fuel tank with 2 good grade of regular, hires gasoline, Never use gasoline that has been standing for months. Do nof mix o1l with #as for this engine, Turn in & counterclockwise dir Fashion (6 open, Crosswise w case, Keep fuel tank full for maximum parer.
ADJUSTMENTS TRACTION DRIVE CONTROL REEL DRIVE BELT AT & Fig, 1 O, TRACTION DRIVE CONTROL ADJUSTMENT: Clevis yoke 'A' has been adjusted for proper position when belts and pulleys are new. As these wear after a prolonged pried, the clevis yoke 'A" will position itself closer to roll pin ‘B'. Contact between the inner sur.
ADJUSTMENTS HEIGHT OF CUT PIVOT FRAME A Fig. 6 HEIGHT OF CUT ADJUSTMENT: Mowers are shipped from the factory set at 1-1/2 inch besought of cut, K another setting is devised, Remove hair pin cotter'd’ and move appropriate hole; up for lower cut and down for higher cut. Be sure all reels are set in the same relative height-of-cut position, FRONT COUNTER BALANCE Fig.
REPLACING REEL DRIVE BELT -~ WOODEN BLOCKS HERE *Fig, 13 Fig, 12 & When replacing the Reel Drive Belt, begin by placing Remove bolt and washers “A¢ from the left wheel hub; wooden blocks under frame members at points shown pull the left wheel assembly 'B' from the axle, being in Figure, A piece equivalent should be careful to remove washers 'C' along with the wheel sufficient.
CHAIN ADJUSTMENTS Whenever a chain adjustment is made on this making, the attitude of the cutting units is also effected, Attitude is the relationship of the cutting unit to a level surface, Proper attitude occurs when all three cutting units are level at the outboard edges with reels 'Y, Be sure distance is equal on bath front cutting units 80 that the eels are posit iced at a right angle 1o the main frame of the riding unit, FRONT REEL DRIVE Fig 17 FRONT REEL DRIVE CHAIN ADJUSTMENT: First loosen stabilize
ADJUSTMENTS REAR REEL DRIVE CHAIN Fig. 18 REAR REEL DRIVE CHAIN ADJUSTMENT: When chain adjustment becomes necessary care must be taken to maintain horizontal attitude of mower unit, There are three (3) rod which must be adjusted to the same relative position. Loosen nuts 'A’ on upper and the two end adjusting rods. To adjust upper rod turn DIFFERENTIAL DRIVE CHAIN nut 'B' clockwise, To adjust end reds rotate rod (on each end of .
ADJUSTMENTS SEAT ADJUSTMENT SEAT ADJUSTMENT: The seat can be adjusted fore and alt by loosening white handle adjusting resew, {see arrow on photo at Thief. (1) Remove screw ana sift awr cleaner from carburetor. (2) Take oif cover and lift support-cup out of foam clement. (3) Remove foam element, {4) A. Wash element in & solvent such as kerosene. B. Squeeze it dry, and re-oil with 3 tablespoons of engine oil, Squeeze again to spread gl . throughout foam. C.
MAIN FRAME and COUNTER BALANCE ASSEMBLY PARTS LIST Ret No, Ref. No. No. {Part Mo Description Used Wo, | Part No.
DIFFERENTIAL and COUNTER SHAFT ASSEMBLY PARTS LIST Ret. No. Rel, o, No. | Part No. Description Used No. | Part No. Description Used Axis 1 47 | 3-6535 | Chain T Braces 1 » | 2710-6 | Connecting Link 1 Hub, Right Side 1 48 | 3-6558 | Thrust Washer -1 Pin ! 49 | 3-6561 | Thrust Washer 05 Belt, Reel Drive 1 50| 3219-2 | but i Lire, Reel 1 51 | 3256-23 | Washer 2 Ring, Tolerance 1 52 | 3-7388 spindle 1 Bushing 2 53 | 249275 |Sprocket, Tidier w/Bearing 1 Sprocket w/ Bushing Ref.
58’ PROFESSIONAL SULKY Assembly PARTS LIST Ret. No. Ref. No. No. |part No. Description Used No. | Part No. Description Used: 1 | 5-0470 | Steering Wheel 1 23 | 242-82 | Nut 3 2 | s2123-6 | Pin 1 24 | 36506 | Bracket 1 3 | 3-6501 | shaft, Steering 1 25 | 242-38 | Wheel Disc Assembly 1 4 | 3-8498 | Washer, Thrust 2 27 | 28939 | Hub w/Bushing 1 5 1 3290-239] Spring Washer 1 28 | 30211 | Perk Pitting 1 § | 3-7138 | Clamp Assembly i 30 | 323-8 | Screw 5 7 | 256-136 | Bushing 4 31 | 3285-9 | Dishwasher 4 8 | 256.
58" PROFESSIONAL ENGINE ASSEMBLY PARTS LIST Ret. Ko, Ref. No. No. | Part No Description Used No. | Part No. Description sed 1 5-1008 Deflector 3-7464 Sip 1 2 221-244§ Engine 1 %5 F-7187 Guide 1 3| 3-7196 | Dip Stick Assembly 1 28 | 3374-15 | Socket Head Caseworker 2 4 1 3-7731 | Pipe.
58" PROFESSIONAL WING MOWER REEL ASSEMBLY PARTS LIST Ref. i No. Ref. Part No, Description Used WNo. | Part No. Description Used 1820-¢ | Resew 3 27 | 3.6625 | Block, Adjusting 2 2 |3254-2 | Lock washer 1 28 | 3-662¢ | Spring 2 3 2256.23 | Washer 9 20 | 3-0623 | Screw, Reel Bearing 2 4 38671 | Hitch, Leif Hand 1 0 | 32102 | Resew 12 * 13-6678 | Hitch, Right Hand 1 31| 3256-3 | Washer t 5 |3.667¢ | Spacer 2 32 |3-7174 | Guard, Reel 2 § |3283.
58" PROFESSIONAL REAR MOWER ASSEMBLY The parts list shown below is used on Rear Mower Assembly only, for parts not shown see Wing Mower Drawings. Ref, No. Ref. No. No. | Part No. Description Used No. {Part No, Description Used.
58" PROFESSIONAL ELECTRICAL SYSTEM ASSEMBLY Ref. No. Rel, No. No. | Part Mo Description Used No. {Part No. Description Used| 1 | 5-118% | Fender, Right Hand 1 20 | 3256-22 | Washer 2 2 | 5-1181 | Shroud & Insulation Says, L 21 | 3219-1 13-7427 | Pad, Foot Rest 1 22 | 322.5 |Screw 1 3+ | 1116988 | Voltage Regulator 1 23 | 3225 |Screw 1 4 | 321047 Screw 17 24 | 4-2390 |Spacer 1 5 | 218-251 | Switch 1 25 | 3217-6 | Nut 2 8 |3-7433 | Bracket Switch & Gen.
ENGINE MODEL 100202 TYPE NUMBER 0220 [s82 g Ble sgef227 @ 358 GREET SEY A SPECIAL TOOLS REQUIRED FOR INSTALLING ASSEMBLIES INCLUDE ALL PARTS SHOWN IN FRAMES [Few gy FEL mg-o// e WAREHOUSES SPECIAL TF TR 700LE Fom estrange LEASE] 2% ASSEMBLIES INCLUDE ALL PARTS SHOWN IN FRAMES W
ENGINE MODEL 100202 TYPE NUMBER 0220 w0t iy eI das, e e ASSEMBLIES INCLUDE ALL PARTS SHOWN IN FRAMES ENGINE PARTS LIST TYPE NUMBER 0220 Ret. Part No. Description No. | Part o, Description 1 | 207566 |Cylinder Assembly 25 208168 | Piston Assembly Standard 2 | 297565 |Bushing Cylinder 288169 | Piston Assembly . 010" 0.5, Note: Requires special tools for 298170 | Piston Assembly .020" 0.3, installation, 286171 | Piston Assembly .030" O.5. 3 189660 |Seal Of 26 298174 |Ring Set 5id.
ENGINE PARTS LIST TYPE NUMBER 0220 Ref, Ref, No.| Part No. Description Nea. | Part No. Description 298177 | Ring Set . 030" O.S. Piston, 202 | 260878 Link « Throttle consists of: 203 | 297718 | Crank Bell 211361 Ring, Piston, Comp., 204 | 23688 Bushing Governor Lever Top, . 030" 0. 8., 5/64" wide 205 | 230754 | Screw Bell Crank Mtg. 211360 Ring, Piston, Compress 208 | 230737 Rod Contort soon, Center, .030" 0.S., 5/64" 209 | 260695 | Spring Governor wide 216 | 260689 Link ~ Choke 211359 Ring, Piston, Oil, .
ENGINE PARTS LIST TYPE NUMBER 0220 Ret. Ref, No. | Part No. Description No. | Bart No. Description 562 | 92613 Bolt Governor Lever 815 | 93307 | Retainer E-Ring 592 | 90356 | Nut Hex. 1024 616 | 230723 | Crank Governor 809 | 260694 | Spring Throttle Link 621 | 207472 | Switch Stop 812 | 298811 | Pipe Fuel 626 | 230740 | Spacer Governor Crank 613 | 93377 Resew Puffier Mtg.
GENERAL INFORMATION This machine uses a single~cylinder Head, air. All fuel should be removed from fuel tank, run the cooed engine, engine until it stops from lack of fuel. The small ES 00 amount of fuel that reaming in the bottom of the tank MODEL SIRE 1002 should then be removed by absorbing it with a clean Bore. . Lee Be1/2m dry cloth. Stroke .. . Displacement While engine is still warm, drain oil from crank Horsepower. -4 HP max. @ 3600 RPM case, Refill with fresh oil. Torque (Ft. -Lbs. ) . 5.93 max.