Form No. 3444-866 Rev B Reelmaster® 3105-D Traction Unit Model No. 03174—Serial No. 400000000 and Up Register at www.Toro.com.
Visit www.Toro.com for more information, including safety tips, training materials, accessory information, help finding a dealer, or to register your product. This product complies with all relevant European directives. For details, please see the separate product specific Declaration of Conformity (DOC) sheet. Whenever you need service, genuine Toro parts, or additional information, contact an Authorized Service Dealer or Toro Customer Service and have the model and serial numbers of your product ready.
Contents Lifting the Front of the Machine ......................... 42 Lifting the Back of the Machine ......................... 42 Lifting the Back of the Machine ......................... 43 Removing the Battery Cover ............................. 43 Opening the Hood ............................................ 43 Lubrication .......................................................... 44 Greasing the Bearings and Bushings ................ 44 Checking the Sealed Bearings..........................
Safety Preparing the Engine ........................................ 62 Storing the Battery ............................................ 62 Troubleshooting ...................................................... 63 Using the Standard Control Module (SCM) ........................................................... 63 This machine has been designed in accordance with EN ISO 5395 (when you complete the setup procedures) and ANSI B71.4-2017.
Safety and Instructional Decals 99-3444 Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal99-3444 99-3444 decalbatterysymbols 1. Transport speed—fast Battery Symbols Some or all of these symbols are on your battery. 1. Explosion hazard 6. Keep bystanders away from the battery. 2. No fire, open flame, or smoking 7.
decal136-3717 136-3717 5. 11-blade reel adjustment 2. Reel height of cut 6. Slow 3. 5-blade reel adjustment 7. Fast 4. 8-blade reel adjustment decal136-3702 136-3702 1. Warning—Read the Operator’s Manual; wear a seatbelt; do not remove the roll bar. 1. Reel speed 2. Warning—Do not modify the roll bar. decal140-7463 140-7463 Note: This machine complies with the industry standard stability test in the static lateral and longitudinal tests with the maximum recommended slope indicated on the decal.
decal136-3678 136-3678 1. PTO—Disengage 5. Lock 2. PTO—Engage 6. Engine—Shut off 10. Fast 9. Lights 3. Lower the cutting units. 7. Engine—Run 11. Slow 4. Raise the cutting units. 8.
decal106-9290 106-9290 1. Neutral 5. High temperature shutdown 9. Outputs 13. Engine—Start 14. PTO 2. Parking brake—Off 6. Reels—active 10. Power 3. PTO 7. High temperature warning 11. Engine—Start 4. In seat 8. Inputs 12.
decal121-3623 121-3623 1. Warning—read the Operator's Manual; do not operate the machine unless you have received training. 5. Thrown object hazard—keep bystanders away. 2. Warning—read the Operator's Manual before towing the machine. 3. Tipping hazard—slow the machine before turning; when driving on slopes, keep the cutting units lowered and your seatbelt fastened. 4.
decal136-3716 136-3716 1. Reel speed 8. Engine coolant 15. Check every 8 hours. 2. Tire pressure 9. Fuses 3. Diesel fuel 10. Engine-oil level 16. Read the Operator’s Manual for lubrication information. 17. Read the Operator’s Manual. 4. Fuel/water separator 11. Belt tension 18. Fluids 5. Engine air filter 12. Hydraulic fluid 19. Capacity 6. Engine oil 13. Parking brake 20. Fluid interval (hours) 7. Radiator screen 14. Battery 21.
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Use Qty. Front wheel assembly Rear wheel assembly Steering wheel Steering-wheel cap Large washer Jam nut Screw 2 1 1 1 1 1 1 3 No parts required – Charge and connect the battery. 4 Roll-bar assembly Flange-head bolt Locknut Hose clamp 1 4 4 1 Install the roll bar. 5 Lift arm kit (optional kit—order separately) 1 Install the front lift arms.
Media and Additional Parts Description Use Qty. Ignition key 2 Start the engine. Operator's Manual Engine operator's manual 1 1 Read before operating the machine. Operator training material 1 View before operating the machine. Pre-delivery checklist 1 Check to ensure that the machine has been properly set up. Certificate of compliance 1 Ensure CE compliance. Note: Determine the left and right sides of the machine from the normal operating position.
3. 4. Secure the steering wheel to the shaft (Figure 3) with a jam nut and tighten it to 27 to 35 N∙m (20 to 26 ft-lb). WARNING Charging the battery produces gasses that can explode. Install the cap to the steering wheel and secure it with a screw (Figure 3). • Keep sparks and flames away from battery. 3 • Never smoke near the battery. Charging and Connecting the Battery 4. When the battery is charged, disconnect the charger from the electrical outlet and battery posts. 5.
4 Installing the Roll Bar Parts needed for this procedure: 1 Roll-bar assembly 4 Flange-head bolt 4 Locknut 1 Hose clamp g011213 Figure 5 1. Positive (+) battery cable Procedure 2. Negative (–) battery cable WARNING Important: If you ever remove the battery, Operating the machine with a modified or damaged roll bar may not adequately protect you, causing possible injury or death in a rollover. • Do not install a damaged or modified roll bar on the machine.
CAUTION Starting the engine with the fuel line vent hose disconnected from the vent tube will cause fuel to flow from the hose, increasing the risk of fire or explosion. A fire or explosion from fuel can burn you and others and can cause property damage. Connect the fuel line vent hose to the vent tube prior to starting the engine. 5 g011161 Figure 8 1. Pivot-shaft link Installing the Front Lift Arms Assembling the Lift Arms to the Machine Parts needed for this procedure: 1 2.
g346438 Figure 10 1. Grease fitting 4. Mounting pin 2. Lift arm flange (left) 5. Lift cylinder (cap end) g346440 Figure 12 3. Snap ring 1. Straight swivel fitting (return hose) 2. Assemble the cylinder to the flanges with the mounting pin and 2 snap rings (Figure 10). 3. Apply No. 2 lithium grease to the grease fittings of the lift arm and the hydraulic cylinder (Figure 10). 2. 90° swivel fitting (lift hose) 3. Wrap a rag around the hose fittings. 4.
7. Torque the swivel fittings of the return and lift hoses to 37 to 45 N∙m (27 to 33 ft-lb). g346476 g353162 Figure 14 1. Straight swivel fitting (return hose) 8. Figure 15 2. 90° swivel fitting (lift hose) Clean hydraulic fluid from the machine. 6 1. Pivot tube (front-carrier frame) 4. Washer 2. Carriage bolt (3/8 x 2-1/4 inches) 5. Link (cutting unit) 3. Plate (front carrier frame) 6. Flange locknut (3/8 inch) 2.
g353163 Figure 17 g353110 Figure 16 1. Carriage bolt (3/8 x 2-1/4 inches) 4. Link (cutting unit) 2. Plate (rear carrier frame) 5. Flange locknut (3/8 inch) 3. Washer 2. 1. Pivot tube (front-carrier frame) 4. Spacer 2. Carriage bolt (3/8 x 1-1/4 inches) 5. Mounting plate (cutting unit) 3. Plate (front carrier frame) 6. Flange locknut (3/8 inch) 2.
g012016 Figure 19 1. Thrust washer 3. Lynch pin 2. Carrier frame 3. g353096 Figure 18 1. Carriage bolt (3/8 x 1-1/4 inches) 4. Mounting plate (cutting unit) 2. Plate (rear carrier frame) 5. Flange locknut (3/8 inch) Important: Ensure that the hoses are free of twists or sharp bends and that the rear cutting unit hoses are routed as show in (Figure 20). Raise the cutting units and shift them to the left (Model 03171). The rear cutting unit hoses must not contact the traction cable bracket.
3. Remove the plug from the bearing housing on the outside end of the right cutting unit and install the weights and gasket. 4. Remove the shipping plug from the bearing housings on the remaining cutting units. 5. Insert the O-ring (supplied with the cutting unit) on the flange of the drive motor (Figure 23). g011218 Figure 21 1. Tipper chain 8 Installing the Cutting Unit Drive Motors No Parts Required g012025 Figure 23 Procedure 1. O-ring 1.
to Adjusting Lift Arm Clearance (page 21) and Adjusting the Lift Arm Stop Bolts (page 22). Important: A lack of clearance at the front plate bracket could damage the lift arms. g353278 Figure 25 g353279 1. Bumper strap Figure 24 1. Lift arm 3. 5 to 8 mm (3/16 to 5/16 inch) gap 3. 0.51 to 2.54 mm (0.02 to 0.10 inch) gap 2. Wear bar (rear cutting unit) 2. Floor plate bracket 5. 4.
g008878 Figure 27 1. Front lift cylinder 2. Jam nut 3. Remove the pin from the rod end and rotate the clevis. 4. Install the pin and check the clearance. 5. Repeat steps 1 through 4 if necessary. 6. Start the engine, raise the cutting units, shut off the engine, remove the key and wait for all moving parts to stop. 7. Measure the distance between the left and right lift arms and the floor plate brackets. 3. Repeat step 2 at the stop bolt for the other lift arm.
the rear cutting unit wear bar and the bumper stop. The correct clearance is 0.51 to 2.54 mm (0.02 to 0.10 inch). 5. Repeat steps 1 through 4 as needed. 6. Lower the cutting units, shut off the engine, remove the key, and wait for all moving parts to stop. 7. Tighten the jam nut. 10 g012628 Figure 30 1. Hood-latch bracket 2. Rivets Adjusting Tire Air Pressure 3. No Parts Required Procedure While aligning the mounting holes, position the CE lock bracket and the hood-latch bracket onto the hood.
12 Installing the Exhaust Guard CE Machines g354465 Figure 32 Parts needed for this procedure: 1. Hood latch 7. 1 Exhaust guard 4 Self-tapping screw Screw the bolt into the other arm of hood-lock bracket to lock the latch in position (Figure 33). Procedure Note: Tighten the nut and bolt until the bolt no longer moves forward and backward in the CE lock bracket. 1. Position the exhaust guard around the muffler while aligning the mounting holes with the holes in the frame (Figure 34).
13 2. Remove the backing and apply the Year of Production decal to the frame near the serial plate as shown in Figure 36. 3. Wipe clean the left frame near the hood lock with alcohol, and allow the frame to dry (Figure 37). Applying the CE Decals Parts needed for this procedure: 1 CE tilt danger decal (140-7463) 1 Production year decal 1 CE decal Applying the CE Tilt Danger Decal 1. Wipe clean the steering-arm bracket with alcohol, and allow the bracket to dry (Figure 35). g352025 Figure 37 1.
Product Overview g016925 Figure 38 1. Frame bracket 4. 2. Tipper bracket Lower the cutting units and mount the tipper bracket to the frame with the 2 carriage bolts and 2 nuts supplied with the kit (Figure 38). g365312 Figure 39 1. Engine hood 4. Steering wheel 2. Operator's seat 5. Front cutting units 3. Control arm 6. Rear cutting unit Controls g336509 Figure 40 1. Tilt steering lever 3. Forward traction pedal 2. Mow/transport slide 4.
• The cutting units only operate when the • Oil Pressure Warning Light mow/transport slide is in the MOW position. The cutting units do not lower when the mow/transport slide is in the TRANSPORT position. The oil pressure warning light (Figure 41) glows if the engine oil pressure drops below a safe level. Engine Coolant Temperature Warning Light Tilt-Steering Lever The temperature warning light (Figure 41) illuminates if the engine coolant temperature is high.
Note: The engine shuts off if you press the traction pedal with the parking brake engaged. Mower Manifold The mower manifold is located under the control-console cover (Figure 42). g353382 Figure 43 1. Seat adjustment lever 2. Fuel gauge g353378 Figure 42 1. Backlap control 2. Reel speed control Seat Adjustment Lever Move the lever (Figure 43) on the side of the seat outward, slide the seat to the desired position, and release the lever to lock the seat into position.
Specifications Operation Note: Specifications and design are subject to Note: Determine the left and right sides of the machine from the normal operating position. change without notice.
Filling the Fuel Tank • Do not store the machine or fuel container where there is an open flame, spark, or pilot light, such as on a water heater or other appliance. Fuel tank capacity: approximately 28 L (7.5 US gallons) • If you spill fuel, do not attempt to start the engine; avoid creating any source of ignition until the fuel vapors have dissipated. Fuel Specification 1. Park the machine on a level surface, lower the cutting units, engage the parking brake, shut off the engine, and remove the key.
Checking the Parking Brake and Seat Run-Interlock Checking the Interlock System Service Interval: Before each use or daily CAUTION 1. Sit in the operator’s seat. 2. Engage the parking brake. 3. Press the cutting unit drive switch to the DISENGAGE position. If safety interlock switches are disconnected or damaged, the machine could operate unexpectedly, causing personal injury. 4. Keep you foot off the traction pedal. 5. Start the engine. • Do not tamper with the interlock switches. 6.
During Operation During Operation Safety • General Safety • The owner/operator can prevent and is responsible • • • • • • • • • • • • • • • – Wait for all movement to stop. – Allow the machine to cool before adjusting, servicing, cleaning, or storing it. Operate the machine only in good visibility and appropriate weather conditions. Do not operate the machine when there is the risk of lightning. Rollover Protection System (ROPS) Safety for accidents that may cause personal injury or property damage.
– Use extreme caution when operating the machine near drop-offs, ditches, embankments, water hazards, or other hazards. The machine could suddenly roll over if a wheel goes over the edge or the edge caves in. Establish a safety area between the machine and any hazard. CAUTION Checking for oil leaks, loose parts, and other malfunctions could result in injury. Shut off the engine and wait for all moving parts to stop before checking for oil leaks, loose parts, and other malfunctions.
Driving the Machine in Transport Mode 1. Move the cutting unit drive switch to the DISENGAGE position. 2. Raise the cutting units to the transport position. 3. Move the mow/transport slide left to the TRANSPORT position. g352480 Figure 45 1. Transport 2. Mow/transport slid Important: Be careful when driving between objects so that you do not accidentally damage the machine or the cutting units. Use extra care when operating the machine on slopes.
Clip Rate (Reel Speed) To achieve a consistent, high quality of cut and a uniform after-cut appearance, it is important that the reel speed be matched to the height of cut. Important: If the reel speed is too slow, you may notice visible clip marks. If the reel speed is too fast, the cut may have a fuzzy appearance. Reel Speed Selection Chart 5-Blade Reel Height of Cut 8-Blade Reel 11-Blade Reel 8 km/h (5 mph) 9.6 km/h (6 mph) 8 km/h (5 mph) 9.6 km/h (6 mph) 8 km/h (5 mph) 9.6 km/h (6 mph) 63.
Adjusting Reel Speed 1. 2. The reel speed knob may be set 1 position on either side of the reel-speed number indicated on the chart to account for differences in grass condition, grass length removed, and personal preference. Verify the height-of-cut setting on the cutting units. Use the column of the Reel Speed Selection Chart listing either 5-blade, 8-blade, or 11-blade reels, and find the height-of-cut listing nearest the actual height-of-cut setting.
After Operation cutting units are over the mowing area, lower the cutting units. • To achieve the professional straight-line cut and General Safety striping that is desirable for some applications, find a tree or other object in the distance and drive straight toward it. • Park the machine on a level surface. • Disengage and lower the cutting units.
Hauling the Machine • Use full-width ramps for loading the machine onto a trailer or truck. • Tie the machine down securely. g352601 Figure 49 1. Bypass valve 3. Close and latch the hood. 4. Connect the tow vehicle to the machine at the tie-down points; refer to Identifying the Tie-Down Points (page 38). 5. Sit in the operator’s seat, and if needed, use the parking brake to control your machine while being towed. Important: Do not start the engine while the bypass valve is open. 6.
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Note: Download a free copy of the electrical or hydraulic schematic by visiting www.Toro.com and searching for your machine from the Manuals link on the home page. Important: Refer to your engine owner’s manual and cutting unit Operator's Manual for additional maintenance procedures. Maintenance Safety Maintenance Safety • If possible, do not perform maintenance while the engine is running.
Maintenance Service Interval Maintenance Procedure Every 400 hours • Check the fuel lines and connections. • Replace the fuel filter canister. Every 500 hours • Grease the bearings in the rear axle. Every 800 hours • If you are not using the recommended hydraulic fluid or have ever filled the reservoir with an alternative fluid, change the hydraulic fluid. • If you are not using the recommended hydraulic fluid or have ever filled the reservoir with an alternative fluid, replace the hydraulic filter.
Daily Maintenance Checklist Duplicate this page for routine use. For the week of: Maintenance Check Item Mon. Tues. Wed. Thurs. Fri. Sat. Check the safety interlock operation. Check the brake operation. Check the fuel level. Check the engine-oil level. Check the cooling system fluid level. Drain the water/fuel separator. Check the air filter, dust cup, and burp valve. Check for unusual engine noises.1 Check the radiator and screen for debris Check for unusual operating noises.
Notation for Areas of Concern Inspection performed by: Item Date Information 1 2 3 4 5 Pre-Maintenance Procedures Lifting the Back of the Machine Using a Hoist Preparing for Maintenance 1. 2. 3. 4. 5. Park the machine on a level surface. Lower the cutting units. Engage the parking brake. Shut off the engine, and remove the key. Wait for all parts to stop moving. 1. Chock the tires. 2. Secure the hoist to the tie-down loop of the rear-wheel fork (Figure 52). Lifting the Front of the Machine 1. 2.
Lifting the Back of the Machine Opening the Hood 1. Release the latches at the left side and right side of the hood (Figure 54). Using a Jack 1. Chock the tires. 2. Jack the back of the machine under the rear wheel motor. (Figure 63). g336542 Figure 55 1. Hood latch 2. Rotate the hood up and back (Figure 55). g363503 Figure 53 1. Frame 3. Tie-down loop (rear-wheel fork) 2. Rear wheel motor 3.
Lubrication Greasing the Bearings and Bushings Service Interval: Every 50 hours (lubricate all bearings and bushings daily when conditions are dusty and dirty). Every 500 hours/Yearly (whichever comes first) g190873 Grease Specification: No. 2 lithium grease Figure 59 The machine has grease fittings that must be lubricated regularly. Dusty and dirty operating conditions could cause dirt to get into the bearings and bushings, resulting in accelerated wear.
g008900 Figure 62 g008903 Figure 65 • Neutral adjust mechanism (Figure 63) Checking the Sealed Bearings Bearings rarely fail from defects in materials or workmanship. The most common reason for failure is moisture and contamination working its way past the protective seals. Bearings that are greased rely upon regular maintenance to purge harmful debris from the bearing area.
Engine Maintenance Engine Safety • Shut off the engine before checking the oil or adding oil to the crankcase. • Do not change the governor speed or overspeed the engine. Engine Oil Specification g008881 Figure 66 Use high-quality, low-ash engine oil that meets or exceeds the following specifications: 1. Dipstick Service Category 4. Push the dipstick down into the dipstick tube and ensure that it is seated fully, then pull the dipstick out and check the oil level. 5.
1. Prepare the machine for maintenance; refer to Preparing for Maintenance (page 42). 2. Unlatch and open the hood, and wait for the engine to cool. 3. Remove either drain plug (Figure 68) and let the oil flow into a drain pan; when the oil stops flowing, install the drain plug. Removing the Air Filter • Check the air cleaner body for damage which could cause an air leak. Replace it if it is damaged. Check the whole intake system for leaks, damage, or loose hose clamps.
8. Fuel System Maintenance Clean the ejection and outlet valve, and install the outlet valve to the port. Installing the Air Filter 1. 2. Inspect the new filter for shipping damage and check the sealing end of the filter and the body. Servicing the Fuel Tank Important: Do not use a damaged element. Service Interval: Every 2 years—Drain and clean the fuel tank. Insert the new filter by applying pressure to the outer rim of the element to seat it in the canister.
Bleeding Air from the Injectors Note: Use this procedure only if the fuel system has been purged of air through normal priming procedures and the engine does not start; refer to Bleeding the Fuel System (page 36). g336554 Figure 71 1. Water separator/filter canister 2. Vent plug 1. When possible, preform each step in Preparing for Maintenance (page 42). 2. Unlatch and open the hood, and if the engine is hot wait for it to cool. 3. Loosen the tube nut for the fuel line to the No.
Electrical System Maintenance Note: Do not fill the cells above the bottom of the split ring inside each cell. Electrical System Safety 5. Install the filler caps with the vents pointing to the rear (toward the fuel tank). 6. Clean the top of the battery by washing it periodically with a brush dipped in ammonia or bicarbonate of soda solution. Flush the top surface with water after cleaning. • Disconnect the battery before repairing the machine.
4. Replace the fuse with the same type and amperage fuse. 5. Assemble the cover onto the control arm (Figure 73). Drive System Maintenance Checking the Tire Pressure Service Interval: Before each use or daily DANGER Low tire pressure decreases machine side hill stability. This could cause a rollover, which may result in personal injury or death. Do not under-inflate the tires. Note: Maintain the recommended pressure in all tires to ensure a good quality of cut and proper machine performance. 1.
Cooling System Maintenance WARNING If the machine is not supported adequately, it may accidentally fall, injuring anyone under the machine. Cooling System Safety Raise a front wheel and the rear wheel off the ground; otherwise, the machine will move during adjustment. 3. • Swallowing engine coolant can cause poisoning; keep out of reach from children and pets. • Discharge of hot, pressurized coolant or touching Loosen the locknut on the traction adjustment cam (Figure 74).
• Preferred option: If distilled water is not available, until the coolant level is midway between the marks on the side of the tank, and assemble the cap to the tank. use a pre-mix coolant instead of a concentrate. • Minimum requirement: If distilled water and pre-mix coolant are not available, mix concentrated coolant with clean drinkable water. Important: Do not overfill the expansion tank. 5. Close and latch the hood.
Brake Maintenance Belt Maintenance Adjusting the Parking Brake Servicing the Engine Belts Service Interval: After the first 10 hours—Check the condition and tension of all belts. Service Interval: Every 200 hours—Check the adjustment of the parking brake. 1. Prepare the machine for maintenance; refer to Preparing for Maintenance (page 42). 2. Loosen the setscrew securing the knob to the parking-brake lever (Figure 77). Every 100 hours—Check the condition and tension of all belts.
Replacing the Hydrostat Drive Belt 1. Controls System Maintenance Insert a nut driver or small piece of tubing onto the end of the belt tensioning spring. WARNING Adjusting Mow Ground Speed When you replace the hydrostat drive belt, you must release the tension on the spring, which is under a heavy load. Releasing the tension on the spring improperly may result in serious personal injury. Be careful when releasing the tension on the spring. 2. 1.
Hydraulic System Maintenance Hydraulic System Safety • Seek immediate medical attention if fluid is injected into skin. Injected fluid must be surgically removed within a few hours by a doctor. • Ensure that all hydraulic-fluid hoses and lines are in good condition and all hydraulic connections and fittings are tight before applying pressure to the hydraulic system. • Keep your body and hands away from pinhole g008918 Figure 81 leaks or nozzles that eject high-pressure hydraulic fluid. 1.
Note: Toro does not assume responsibility for damage caused by improper substitutions, so use products only from reputable manufacturers who will stand behind their recommendation. High Viscosity Index/Low Pour Point Anti-wear Hydraulic Fluid, ISO VG 46 Material Properties: Viscosity, ASTM D445 cSt @ 40°C (104°F) 44 to 48 g341294 Figure 82 140 or higher Viscosity Index ASTM D2270 1.
If the fluid becomes contaminated, contact your authorized Toro distributor because the system must be flushed. Contaminated fluid looks milky or black when compared to clean oil. 1. Prepare the machine for maintenance; refer to Preparing for Maintenance (page 42). 2. Disconnect the hydraulic hose (Figure 83) or remove the hydraulic filter (Figure 84) and drain the hydraulic fluid into a drain pan. g341294 Figure 85 1. Cap 3. Dipstick 2. Filler neck (hydraulic-fluid reservoir) g353456 Figure 83 1.
Cutting Unit System Maintenance Blade Safety A worn or damaged blade or bedknife can break, and a piece could be thrown toward you or bystanders, resulting in serious personal injury or death. • Inspect the blades and bedknives periodically for excessive wear or damage. • Use care when checking the blades. Wear gloves and use caution when servicing them. Only replace or backlap the blades and bedknives; never straighten or weld them.
3. Lift the magnetically mounted console cover (Figure 87) to expose the mower manifold. 2. Press the cutting unit drive switch to the ENGAGE position. 3. Apply lapping compound to the reel with a long-handle brush. DANGER Contacting the cutting units when they are moving could cause personal injury. To avoid personal injury, be certain that you are clear of the cutting units before proceeding. Important: Never use a short-handled brush. 4.
5. Wash all lapping compound off from the cutting units. Cleaning 6. For a better cutting edge, run a file across the front face of the bedknife after lapping. Washing the Machine Note: This removes any burrs or rough edges that may have built up on the cutting edge. Wash the machine as needed using water alone or with a mild detergent. You may use a rag when washing the machine. Important: Do not use brackish or reclaimed water to clean the machine.
Preparing the Engine Storage 1. Drain the engine oil from the oil pan and install the drain plug. 2. Remove and discard the oil filter. Install a new oil filter. 3. Fill the engine with specified motor oil. 4. Start the engine and run it at idle speed for approximately 2 minutes. – Engage the parking brake. 5. Shut off the engine and remove the key. – Shut off the engine and remove the key. 6. Flush the fuel tank with fresh, clean fuel. – Wait for all movement to stop. 7.
Troubleshooting Using the Standard Control Module (SCM) The Standard Control Module is a potted electronic device produced in a one-size-fits-all configuration. The module uses solid state and mechanical components to monitor and control standard electrical features required for safe product operation. The module monitors inputs including neutral, parking brake, PTO, start, backlap, and high temperature. The module energizes outputs including PTO, Starter, and ETR (energize to run) solenoid.
Each row (across) in the logic chart that follows identifies input and output requirements for each specific product function. The product functions are listed in the left column. The symbols identify the specific circuit condition including energized to voltage, closed to ground, and open to ground.
EEA/UK Privacy Notice Toro’s Use of Your Personal Information The Toro Company (“Toro”) respects your privacy. When you purchase our products, we may collect certain personal information about you, either directly from you or through your local Toro company or dealer.
California Proposition 65 Warning Information What is this warning? You may see a product for sale that has a warning label like the following: WARNING: Cancer and Reproductive Harm—www.p65Warnings.ca.gov. What is Prop 65? Prop 65 applies to any company operating in California, selling products in California, or manufacturing products that may be sold in or brought into California.
The Toro Warranty Two-Year or 1,500 Hours Limited Warranty Conditions and Products Covered Parts The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for 2 years or 1,500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
